In-Ear

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The True Adaptive Noise Cancelling technology is a features which adjusts noise-cancelling levels in real-time, 50,000 times per second to account for environmental ambient noises and personal attributes such as movement, hair and eyeglasses to deliver best-in-class Noise Cancelling and immersive sound in any environment.  
With the help of Feed Forward and Feed Backward microphones, the Adaptive Noise Cancelling technology fully monitors exterior sounds picking up low-frequencies and neutralizing them before they reach the ear. The headphones generate a sound that's phase-inverted by 180 degrees to the unwanted noise, resulting in the two sounds cancelling each other out. 
In addition, all headphones allow the listener to adapt or adjust the level of ambient noise through features like Ambient Aware and TalkThru.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

The JBL Tour Pro 2 allows you to find your preferred control method in any scenario. When you want to control your headphones, you no longer need to take your phone out, open the JBL Headphones app and wait for the headphones to connect in the app. All features are accessible directly on the Smart Case, where you can easily select any key feature, you know from the app.

Some of the features you can access on the Smart Case includes playing and pausing your music, skip to the next/previous track, volume adjustment, answer/reject calls, customize the EQ settings, Spatial audio, ANC and Ambient Sound Control, timer & clock, receive notifications, screensavers, and a battery indicator. 

The JBL Tour Pro 2 is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth. 

As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

 

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

 

TUNE FLEX
Software Update Release Notes
------------------------------------------------------------------------
Software Version:  V3.1.0 (global)
Release Date:  September 14, 2022
Release Media:  OTA (over the air) via JBL Headphone App


What’s New

1. Improved the connectivity between left and right earbud.
2. ANC (active noise cancelling) can be activated more quickly.
3. Optimized the APP user experience for better flow.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

This unit is fully dust-proof, and can withstand continuous immersion in water (up to 1.5 meters / 4.9ft for 30 minutes). 

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

LIVE FREE 2 TWS
Software Update Release Notes
------------------------------------------------------------------------
Software Version:  V6.9.8
Version (iOS):  V5.7.9
Version (Android):  V5.7.9
Release Date:  July 8, 2022
Release Media:  OTA via JBL Headphone App


What’s New

1. Added Microsoft Swift Pairing feature.
2. Fixed a few minor software bugs for better user experience.

If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

After setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.

Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones

Get your notifications
Double-tap the Action button.

Stop your Google Assistant
Touch the Action button.

Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.

For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones

 

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

There are several easy ways to prevent damage to your headphones, and please follow the steps below.

1. If the USB port has a cover, please always have it covered, except when charging.

2. Always be sure the USB port and connector are dry before connecting to charge.

3. Do not allow any oils, stains, sweat, or corrosive materials to contact the charging port. It will eventually damage the port.

4. Do not damage or block the USB port. For example, do not force it in if you have trouble inserting the USB connector into the port. Instead, examine the port and remove foreign substances that might be inside or blocking the port.

If you need more assistance, please contact the Customer Service team.
 

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

 

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

This headphone is supported by the My JBL Headphones App.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

Visit the App Store and download the ‘Amazon Alexa’ App.

 

1. Click the Plus(+) button on the top right of the screen.
2. Then select ‘Add Device‘.
3. Select headphones from the list and then choose your Headphones from the list of available devices.
4. Follow the rest of the instructions in the Alexa App to complete the setup.

If you are experiencing issues with your headphones' Bluetooth disconnecting and reconnecting while on standby, there is a new Firmware Update app to resolve this issue. Start by downloading the app  "JBL Firmware Update" (see links below).
Google Play Store: https://play.google.com/store/apps/details?id=com.jbl.tune.update
App Store: https://apps.apple.com/gb/app/jbl-firmware-update/id1548227663

Once downloaded, you can update your headphones firmware from there. 
Below you can see step by step images of the update process.

      

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 

In case one of the earbuds loses its connection, you can do a manual pairing process by following the instructions below.

1. You can manually pair your earbuds by placing both back into the charging case and closing the lid.
2. Open the lid again, take them out of the charging case, and tap 3 times on each earbud simultaneously until you see the purple LED flash.
3. You will see the earbuds enter into Bluetooth pairing mode, and the connection between the Left and Right earbud is successful.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

Visit the App Store and download the ‘Amazon Alexa’ App.

 

1. Click the Plus(+) button on the top right of the screen.
2. Then select ‘Add Device‘.
3. Select headphones from the list and then choose your Headphones from the list of available devices.
4. Follow the rest of the instructions in the Alexa App to complete the setup.

This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

Visit the App Store and download the ‘Amazon Alexa’ App.

 

1. Click the Plus(+) button on the top right of the screen.
2. Then select ‘Add Device‘.
3. Select headphones from the list and then choose your Headphones from the list of available devices.
4. Follow the rest of the instructions in the Alexa App to complete the setup.

After setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.

Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones

Get your notifications
Double-tap the Action button.

Stop your Google Assistant
Touch the Action button.

Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.

For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones

 

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

There are several easy ways to prevent damage to your headphones, and please follow the steps below.

1. If the USB port has a cover, please always have it covered, except when charging.

2. Always be sure the USB port and connector are dry before connecting to charge.

3. Do not allow any oils, stains, sweat, or corrosive materials to contact the charging port. It will eventually damage the port.

4. Do not damage or block the USB port. For example, do not force it in if you have trouble inserting the USB connector into the port. Instead, examine the port and remove foreign substances that might be inside or blocking the port.

If you need more assistance, please contact the Customer Service team.
 

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

This headphone does not feature volume control. You must manually control volume from your device.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.

This headphone does not feature volume control. You must manually control volume from your device.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

If you are experiencing issues with your headphones' Bluetooth disconnecting and reconnecting while on standby, there is a new Firmware Update app to resolve this issue. Start by downloading the app  "JBL Firmware Update" (see links below).
Google Play Store: https://play.google.com/store/apps/details?id=com.jbl.tune.update
App Store: https://apps.apple.com/gb/app/jbl-firmware-update/id1548227663

Once downloaded, you can update your headphones firmware from there. 
Below you can see step by step images of the update process.

      

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

There are several easy ways to prevent damage to your headphones, and please follow the steps below.

1. If the USB port has a cover, please always have it covered, except when charging.

2. Always be sure the USB port and connector are dry before connecting to charge.

3. Do not allow any oils, stains, sweat, or corrosive materials to contact the charging port. It will eventually damage the port.

4. Do not damage or block the USB port. For example, do not force it in if you have trouble inserting the USB connector into the port. Instead, examine the port and remove foreign substances that might be inside or blocking the port.

If you need more assistance, please contact the Customer Service team.
 

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

Visit the App Store and download the ‘Amazon Alexa’ App.

 

1. Click the Plus(+) button on the top right of the screen.
2. Then select ‘Add Device‘.
3. Select headphones from the list and then choose your Headphones from the list of available devices.
4. Follow the rest of the instructions in the Alexa App to complete the setup.

As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

 

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

This headphone does not feature volume control. You must manually control volume from your device.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
 

1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
 

As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

 

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.

This headphone does not feature volume control. You must manually control volume from your device.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
 

Things to try

• “What’s the weather?”
• Play Niall Horan
• Play NPR on iHeartRadio
• Set a timer for 5 minutes
• What new skills do you have?

Stop Alexa when she talks
While Alexa is talking, press and release the Action button then say “Stop”.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices

Visit the App Store and download the ‘Amazon Alexa’ App.

 

1. Click the Plus(+) button on the top right of the screen.
2. Then select ‘Add Device‘.
3. Select headphones from the list and then choose your Headphones from the list of available devices.
4. Follow the rest of the instructions in the Alexa App to complete the setup.

To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.


Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings  once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.

After setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.

Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones

Get your notifications
Double-tap the Action button.

Stop your Google Assistant
Touch the Action button.

Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.

For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones