How To
How To
1203 results
-
To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.Was this helpful? Thank you for your feedback!
-
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.Was this helpful? Thank you for your feedback! -
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The red charge light turns off when charging has finished.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. The feature is switched on by default, but you can SHORT press the multi function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
When the earbuds are connected to the USB wireless dongle and Bluetooth connection at the same time, triple tab on the left earbud to switch between the two connections. You'll hear a tone after you triple tab the left earbud signaling the switching is in progress. If you receive an incoming call from your mobile device, you can double tap either earbud and the earbuds will automatically switch over to that connection while answering the call.Was this helpful? Thank you for your feedback!
-
All updates will happen over-the-air, meaning that your device just needs to be connected via your Wi-Fi network with at least 30% battery and plugged into the charger, then it will update during the night if there are any new updates available.Was this helpful? Thank you for your feedback!
-
By using Google Home app, and if a software is available then the app will notify you about the newest software available. Google Home app can be downloaded from Apple Play Store or Google Play Store.Was this helpful? Thank you for your feedback!
-
If your JBL Link 10 or Link 20 is out of range, setting up a personal hotspot from your mobile device will allow your Google Assistant to answer again. However, this process requires two mobile smartphones, one as the "mobile hotspot" and the second to connect the JBL Link 10 or Link 20 to your network.Was this helpful? Thank you for your feedback!
-
Switch the headphone ON, then press both volume buttons (VOL + and VOL-) at the same time, and hold them for 5-6 seconds. The headphones are now reset to factory default.Was this helpful? Thank you for your feedback!
-
The JBL Quantum TWS works on most mobile devices, however, some mobile devices restrict the utilization of it's audio and microphone functions via USB-C causing there to be no audio or microphone operation. In these cases we recommend connecting to the earbuds using their Bluetooth connection.Was this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
Let's say you have 4 LINK devices in your home and you start your day with "OK Google, How is the weather?".
All of your devices will "light up" and start listening to the command. However, only one of the speakers will give you the information (if they are under the same account).
The speaker with the best microphone reception will respond with an answer.
Please note: if you have muted all speakers or 3 out of 4 are muted, then only one will respond and the rest will not react.
If all speakers are muted, all will be silent.Was this helpful? Thank you for your feedback! -
For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.Was this helpful? Thank you for your feedback!
-
BT sources are volume controlled by the Primary Volume control. BT volume relative to other sources must be adjusted either on the BT source or on the mixer’s input volume controls. Bluetooth does not occupy any of the other inputs.Was this helpful? Thank you for your feedback!
-
Press the microphone button (located on the LEFT arm) to turn on the first RunSafe mode. The first mode blinks continually. When you press the microphone again, the second mode is initiated which features 2 blinks on followed by 2 seconds without. Pressing the microphone again is the third mode which is 3 blinks on followed by 3 seconds without.Was this helpful? Thank you for your feedback!
-
In our Quick Start Guide, there is a section under "One Touch Play Feature", where we explain how it works. We advise to take a look at it.Was this helpful? Thank you for your feedback!
-
After pressing the Play button, you must wait 3 seconds before you can press the Play button again when listening to videos over AirPlay.
Was this helpful? Thank you for your feedback! -
If you want to pair and connect to a different device, make sure the headphones are turned off. Proceed to turn the headphones on by pressing and holding the power button for 3- 5 seconds until you hear the audible voice stating “power on” followed by “looking for device.” You will see the LED alternate between blue and red as it searches for your new device. Make sure your device is in search mode. Within seconds your headphone should appear as one of your discoverable devices. You will then hear the audible voice stating, “audio connected” followed by a blinking blue LED light located on the inline microphone indicating that it is now connected to a device.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are turned on and connected to your smart device. Press and hold the Microphone button located on the LEFT arm of the neckband. You should be able to activate Siri/Google within 3 seconds after pressing the Microphone button.Was this helpful? Thank you for your feedback!
-
1) Download and run the latest JBL Connect app on your phone 2) The JBL Connect app will begin discovering your JBL Boombox (please make sure your speaker is connected via Bluetooth first) 3) Use the toggle switch in the JBL Connect App to change the phone button to now have the voice assistant function 4) Simply press the “Play” button on your JBL Boombox (you will hear a brief tone) and begin speaking your commands via SIRI and Google Now. 5) Please check the below links for more information regarding SIRI and Google Now available voice commands: SIRI: https://support.apple.com/HT204389 Google Now: https://support.google.com/websearch/answer/2940021Was this helpful? Thank you for your feedback!
-
Tap and hold the right earpiece for 4 seconds.Was this helpful? Thank you for your feedback!
-
To increase the volume, quickly press the top button located on the inline microphone with several quick clicks. If you want to decrease the volume, quickly press the bottom button with several quick clicks until desired volume is achieved.Was this helpful? Thank you for your feedback!
-
To answer and hang up calls, press the pause/play button located on the left arm of the Soundgear.Was this helpful? Thank you for your feedback!
-
To remove the enhancer, pinch the edge opposite of the sound tunnel between your thumb and forefinger and firmly pull up and off the ear bud. Replacement enhancers are specific to the left and right ear bud. An (L) or (R) and size indicator is located on the inside of the enhancer. When changing the enhancers, you must place the right enhancer on the right ear bud and the left enhancer on the left ear bud. Firmly grasp the earbud with one hand and align the sound tunnel of the enhancer with your other hand and stretch the enhancer up and over the top of the red earbud. Check the alignment of the sound tunnel to insure best sound performance. If sound is muffled or weak, check and rotate sound tunnel. Most people use the same size for Right and Left but it is possible to use different sizes because some ears are not symmetrical. - If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email ua.jblsupport@harman.com to request yours today.Was this helpful? Thank you for your feedback!
-
The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)