Replacement parts are available from authorized dealers and Service Centers. Please contact our customer service department for more information and contact details.

At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.

You can view stats from your past workouts by going to your dashboard and tapping the Fitness quadrant. Tap the workout you would like to view. Your average and peak heart rate, heart rate distribution through your training session, and a graph of your real-time heart rate, will all be shown.

For headphones with version 4.0 of the firmware, updates will be available via jbl.com/app. For headphones with firmware version 5.0 or higher, update notification will be pushed via the app

The sensor is located in the LEFT ear bud. The left enhancer will feature a cut out for the sensor and should be fully exposed.

The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.

The microphone is located on the remote small hole on the right side

Under the little hole next to the phone reciever button.

On the BT and ELITE NXT series over-ear and on-ear models, the serial number sticker is on the inside of the headband left side, visible when the size adjustment is pulled all the way out. Serial numbers are also shown on the boxes. On ELITE 100 in-ear, it is on the box only.

The Serial Number is located on the strap hook (see image below), it may be necessary to remove the strap to see it clearly.

It is a tiny white sticker, located on the inside of the left-hand size adjustment slider on E35.

Our LINK BAR supports the following:
MP3, AAC-LC, HE+ACC, FLAC, Vorbis, Wav, CELT/opus via Wi-Fi streaming, and with Bluetooth SBC and AAC.

JBL Charge 3 is available in 5 fashionable finishes: Teal, Gray, Black, Blue and Red.

Connecting a USB stick

1. You can enjoy music from your USB Stick directly into the Partybox device.
2. Insert the Stick into theport, located on the back of your Partybox.
3. The USB Stick has to be formatted FAT16 or FAT 32 and supports MP3, WAVE and WMA Music files.
4. It will start automatically playing the content on your USB stick.

AUX Connection

1. You can connect any devices through the analog connection
2. Use an analog cable (Not included in the box) and connect your device.
3. Press play on your external device and enjoy the music!

RCA Connection (*Partybox 200/300/1000 Only)

1. The Partybox features both Input and Output RCA connection.
2. Connect your RCA cable (not included) to either one of the ports.
3. You can use it with your DVD/BlueRay player or AVR system.

Guitar and Microphone

1. Connect your to the dedicated port or connect your electric   to the
2. You can mix sound or make your own karaoke party with your Partybox.
3. Sing or play through your devices.
   1. To adjust the volume of the audio source, press volume+ or volume- buttons.
   2. To adjust the volume of the microphone or guitar, rotate the or

 

Charging external devices

1. Whenever your mobile device needs some extra power, the Partybox can help you!
2. Featuring a USB Charging port for both Music (USB on a stick) or when you need to charge your device.
3. Simply connect your device to the port and start charging.
   1. NOTE: The Partybox 200 needs to be connected to AC power all the time to charge or function as a speaker.
   2. The Party 300/310 has a battery and can charge any device without needing AC power (unless the product's battery is depleted then you need to recharge via AC power).

There are many ways to enjoy your JBL Partybox On-The-Go, 100, 200, 300, 310 & 1000. The options are endless and you are in control of the party

All of our in-wall/in-ceiling speakers are designed to be used in a wall without the need for a back-box. The specs provided are based on no back-box. However, when adding a back-box (really only possible when doing new construction), you will improve the low frequency response a bit, getting a tighter bass response.

JBL Xtreme, JBL Pulse 2, JBL Charge3, JBL Flip 3, Pulse 3, and Flip 4 Android, Google Now, Google Play are trademarks of Google Inc. Siri, iTunes, and Apple Music are trademarks of Apple Inc. Spotify is a registered trademark of Spotify AB. IOS is a registered trademark of Cisco in the US and is used by Apple under license.

The first JBL speakers featuring the JBL Connect technology are: JBL Flip 3, JBL Pulse 2, JBL Xtreme, JBL Boost TV and JBL Charge 3, SB 450 A firmware upgrade is available for the JBL Charge 3 ,which will upgrade Connect to JBL Connect+. After this fw upgrade, it is no longer possible to connect the Charge 3 with other products which have JBL Connect ( Flip 3, Boost TV, Pulse 2, Xtreme )

JBL Quantum 300, 350, 400, 600, 610, 800, 810 ONE, TWS and Stream are working with the QuantumENGINE

It is a model made for vocal use.

The “Speaker” mode allows the JBL QuantumENGINE to receive more than two channels of audio. It also prevents some applications from adding extra signal processing intended for other headphones, which would negatively impact the performance of the JBL QuantumSURROUND or JBL QuantumSPHERE 360 technology.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 400 Game, right-click, and select "Set as Default Device".  Check on the top bar of the JBL QuantumENGINE whether your headset's game-chat balance dial is set correctly. Check the JBL Quantum 400 Game device and make sure it is not muted or turned all the way down.

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 910 Wireless Game, right-click, and select "Set as Default Device".  Check your headset's game audio chat balance dial and ensure that the balance is correct. Check the JBL Quantum 910 Wireless Game device and make sure it is not muted or turned all the way down.

Make sure the volume is turned up and that the correct device has been selected in the system sound settings. Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default communication device is selected under Control Panel > Sound > Playback. Select JBL Quantum ONE Chat, right-click, and select "Set as Default Commuication Device". Check your headset's game audio chat balance dial, and ensure that the balance is correct. Check the JBL Quantum ONE Chat device and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up and your microphone is unmuted. Check that only one voice chat application is in use while in-game. If you're connected to the PC, make sure that the communication device is selected under Control Panel > Sound > Recording. Select the JBL product and select "Set as Default Device". Check on the top bar of the JBL QuantumENGINE whether your headset's game-chat balance dial is set correctly.

-       Alexa is not available in all languages and countries. For countries without Amazon Alexa, you can double tap to activate the native voice assistant on your mobile device.

-       The Google Assistant isn’t available in certain languages and countries. For countries without Google Assistant, you can double tap the left ear cup on the headphone to activate the native voice assistant on your mobile device.

Please check your OS version. If you are using an iPhone with OS version of 8.3 or lower , please upgrade your system to the latest version.

The BT module takes approximately 3 seconds to activate and connect with the headphones.

If your Micro II does not sense an audio signal on its input, it goes into Standby to save power. It should wake up again when audio is sensed. Since Micro II senses audio on its input, not on the speaker volume, always turn up the volume on the source, then control speaker volume on the Micro II. This way it will not go into Standby unless music stops.

There is a known issue that Spotify Connect and Amazon Music are not stable over a wired connection. If you primarily use these services, it is recommend to connect to the home network via Wi-Fi.

When not connected to AC power, the speaker will be automatically switch off after 1 hour of inactivity to save battery consumption. You can adjust the auto standby time on JBL One app.

This speaker has an auto calibration feature, which measures the space around the speaker and adjusts the sound quality based on the room around it. Auto calibration will automatically work when you power on the speaker and begin playing music. For the best sound, we recommend placing the speaker at least 18 inches (0.5 meters) away from any walls.

Orange cable is JBL signature color!

Vehicles that have an Active Noise Cancelling system are prone to encounter sound issues when an after-market subwoofer is installed. The sound issue can be described as a hum or low-frequency tone. To understand why this is happening it's important to understand how the ANC system in a vehicle works.

 

The ANC system's main job is to pick up on any internal/external low-frequency sound, such as engine/road noises, and block them out. The signal is sent to its ANC processor to produce a reverse phase audio signal and is sent back to the speaker system. The inverted phase signal will cancel out the internal/external low-frequency sound, blocking out any unwanted noise.

 

When you add an aftermarket subwoofer into the mix the ANC system hears the subwoofer output as being part of the engine/road noise. The ANC system believes the low-frequencies being emitted by the subwoofer are part of the unwanted noise and this leads to the ANC system producing an out-of-phase low-frequency signal to block the sub's output.

 

To identify if your vehicle has an ANC system you can do one of two things.

 

1. Look up your vehicle's specifications online and verify if an ANC system is installed.
2. Drive your vehicle, play music, put your vehicle in park, and then either turn off the engine or open your door. If the subwoofer plays as it should you'll know you have an ANC system.

To fix the sound issue you'll need to disable the ANC system. You can accomplish this by doing one of three things.

 

1. Contact your dealership to see if they can disable the ANC system
2. Use an ANC Bypass Harness
3. Disable the ANC system yourself

 

There is a setting in the JBL One app called Bluetooth reconnection. You can change the behavior to enable it to automatically reconnect every time the speaker is turned on, if this is the behavior you want.

We believe the baseline performance of the QuantumSPHERE technology is cutting edge in terms of localization. The calibration feature improves upon this performance by calibrating the system to your individual anatomy.

If the preset DAB/FM station signal is not strong enough the alarm will go off in buzzer mode instead. Make sure the signal is strong enough, by checking that the station plays without static or distortion (FM).

If you have a mesh network (more commonly seen in Eero Mesh networks), it is possible that you may experience your satellite speakers or subwoofer intermittently disconnecting from the soundbar. This is similar to normal interference that occurs with products on a similar wireless frequency. The special thing about Eero mesh networks is that they do not allow you to move a device to the 5Ghz or 2.4Ghz band. The system will automatically decide which devices should be on which band and will move them accordingly (switching whenever needed). Some of our soundbars run on a 5Ghz frequency which is where the interference can occur. Since we cannot change the signal in which they operate and we cannot change the band they are connected to via their Eero mesh network, there are a few things you can do to try and stop this from occurring. 

  

1. Move the mesh nodes far away from the soundbar 
2. Use the 2.4Ghz band instead of the 5Ghz band (if your mesh system allows this) 
3. Ensure to enable/utilize the MU-MIMO setting (not applicable to all mesh systems). Please refer to your router's website to see if MU-MIMO is being utilized by default. 

  

What is MU-MIMO? 

MU-MIMO stands for Multi-User, Multi-Input, Multi-Output. This allows for the router to send a signal to multiple devices at one time vs. the previous version in which the router would be able to connect to multiple devices, but only send the signal to one device at a time. 

  

NOTE: You may notice that when the soundbar is turned on, there may be a dip in the immediate internet speed, but it will go back to normal within less than a minute.

This speaker has a USB-C charging protection safety feature. This safety feature will play an alert sound & cause the LED indicators to flash when the charging port has detected water, salt, or other chemical. When you encounter the alert you will need to remove the charging cable, wipe down any excessive moisture on or around the charging port, and leave the speaker in a area to completely dry off. Once it is completely dry, you'll be able to plug the USB-C cable back in and charge your speaker.

The internal cable is about 5 cm long, including the micro-USB plug. The flexible part is about 2.4 cm. This length has been chosen to permit the case to be closed without the cable being in the way, or be closed with a pair of in-ear headphones inside the box. In-ear types with big battery boxes or remote controls may not fit inside the closed case. On-ear or over-ear types will often have the charging socket placed in such a manner that you can arrange the cable to reach the socket.

This is because standard USB charging is possible from so many sources and chargers, and also from computers. There is a charging cable in the box, which permits charging from all USB chargers of at least 1A capacity.

In the ANC on mode, we take advantage of advanced signal processing to finely tune, and personalize the audio performance. In passive and in ANC off mode, that signal processing is not running, so you may hear a difference in audio performance

Using Wi-Fi allows you to listen to your music in a higher sound quality since Bluetooth protocol compresses the audio signal, where Wi-Fi data easily stream HD Audio content. Take calls without interrupting your current audio music, where Bluetooth will interrupt the stream, because it is a one-way protocol. Control your music from anywhere in the house, where Bluetooth have a limited range. Play the same music across multiple speakers and when using the newest connect features, such as Spotify Connect or Chromecast built-in, then you don't have to worry about battery life, since the devices playing is doing all the data transmission compared to Bluetooth, where it is data between source and device.

This speaker will go to standby mode after 10 minutes inactivity. It turn on when you start playing to it again.

Only if you have pressed the button on the remote or Boost TV itself.

No - it is not designed to work with a wireless microphone.

Yes, when casting music to your JBL Playlist, your speaker is connected to Google Cloud, which will turn your smart device into a remote control, rather than streaming music directly to the Playlist. You can easily do other things with your phone while using Chromecast, such as gaming, texting, make calls, watch Youtube etc. This will not interrupt the music that you are casting.

Yes, after 10 minutes of no audio activity, the soundbar will enter standby-mode automatically. Or you can do it yourself by short pressing the Power button.

No, the re-broadcast signal is in stereo. Stand alone speakers will play both Left and Right channels.

Yes, if no audio is present and no buttons are pressed, DUET will go into standby after approx. 10 minutes.

Yes, it will only go back to default volume if the power is switched off or if the device is reset. The standard volume is set to 50%.

The core settings: EQ, smart button, auto features will be recalled from the headphone when recharged. Ambient aware settings will default to off when the headphone is restarted after charging.

There is no plan for adding JBL Connect support for Playlist speaker. But you can group any speaker together that support Chromecast built-in for multi-room experience.

No, it will not change the TruNote autocalibration results. TruNote equalizes the acoustics of the headphones to the specific fit to your head As is the case with any supplemental equalization setting, it will change how the audio sounds to the user

No, you can certainly take off the front grill if you like the design of the speaker without the grill. However, do not touch the tweeters or woofers, as they can be damaged if you touch them. For ourdoor purposes, we do not recommend taking off the front grill.

The speaker is not intended to play under water, but it will continue to play even though it is submerged under water.

Yes. This product has battery power save features.

 All JBL Quantum headset models work only through 3.5mm audio jack (aux) connected to the Xbox controller. You cannot connect to any Xbox Series console via Bluetooth. 

Please note: JBL QuantumENGINE is only available on PC.
 

XTREME 4

Software Update Release Notes

------------------------------------------------------------------------

Version:  0.6.4.0

Release Date: November 18th, 2024

Release Media: OTA (over the air) Update through JBL Portable App

 

What’s New

1. Add ability to retain stereo group set up permanently even after speaker is turned off
2. Performance improvements

------------------------------------------------------------------------

Version:  0.5.5.0

Release Date: May 23, 2024

Release Media: OTA (over the air) Update through JBL Portable App

 

What’s New

1. Add PartyBoost Tone
2. Auracast Mode support across platforms
3. Bug fixes