JBL Boombox 3
Bærbar højttaler
Sold from 2022 until now
Getting started with your JBL Boombox 3
Documents & Downloads
Product Specifications
- Udgangseffekt (W)
- 1x80W RMS-subwoofer + 2x40W RMS-midrange + 2x10W RMS-tweeter (AC mode) 1x60W RMS-subwoofer + 2x30W RMS-midrange + 2x8W RMS-tweeter (Battery mode)
- Dynamisk frekvensområde (Hz)
- 40 Hz - 20k Hz
- Mål (cm)
- 48.2 x 25.7 x 20.0
- Mål (inch)
- 19.0 x 10.1 x 7.9
- Vægt (kg)
- 6.7
- Vægt (lbs)
- 14.7
- Bluetooth-profiler
- A2DP 1.3, AVRCP 1.6
- Bluetooth-frekvens
- 2.402GHz - 2.480GHz
- Bluetooth sender-modulation
- GFSK, π/4 DQPSK, 8DPSK
- Bluetooth sender-effekt
- ≤ 9 dBm (EIRP)
- Bluetooth-version
- 5.3
- Ladetid (timer)
- 6.5
- Spilletid (timer)
- 24
- 3,5 mm lydindgang
- Ja
- Bluetooth
- Ja
- Charging cable
- Ja
- JBL PartyBoost
- Ja
- Powerbank
- Ja
- Vandtæt
- Ja
- Wireless
- Ja
- Genopladeligt batteri
- Ja
- IPX-rating
- IP67
Kraftfuld lyd. Hele dagen.
Vi har lige gjort vores kraftigste bærbare Bluetooth-højttaler endnu bedre. JBL Boombox 3's ikoniske silhuet har fået en markant opgradering med et robust metalhåndtag med silikonegreb, to sidehætter og den ikoniske stofbeklædning, der både er vand- og støvtæt. Indvendigt er den fornyet med en ny subwoofer, der giver langt dybere bas og kraftfuld JBL Original Pro Sound med lavere forvrængning. 24 timers spilletid tager dig hele vejen fra morgentræningen til en aften med dine venner. Du får lyd uden grænser, når du forbinder flere højttalere med JBL Portable-appen.
FAQs & How-Tos
-
If you are having trouble with distortion or drop outs, try the following suggestions:
Move the audio source closer to the speakers
Move the speakers closer to each other
Make sure the streaming speaker (host) only connects to one audio source, disconnect the Bluetooth connection between the streaming speaker (host) and other audio source
Make sure the audio source only connects with one streaming speaker (host), disconnect the Bluetooth connection between the audio source and other speakers
Restart both your speakers and the audio source
Make sure speakers are away from other sources of wireless signal – you could be experiencing interference
Re-pair the audio source with your speaker
If you’re streaming audio content from the internet, the issue could be with the internet connection and not your speakerWas this helpful? Thank you for your feedback! -
BOOMBOX 3
Software Update Release Notes
------------------------------------------------------------------------
Software Version: V0.3.0.0
Version (iOS): N/A
Version (Android): N/A
Release Date: July 27, 2022
Release Media: OTA (over the air) via JBL Portable App
What’s New- Fixed Issue: Red LED keeps flashing after powering off the device
- Fixed Issue: Battery indicator LEDs do not change when charging an external device via USB-A port
- Fixed Issue: Charging LED keeps flashing after speaker is fully charged
- Other minor bug fixes and performance improvements
Was this helpful? Thank you for your feedback! -
You will need to dry the charging port completely before plugging in power for charging.
Was this helpful? Thank you for your feedback! -
This product does not feature speakerphone or voice assistant functionality as it does not have a microphone.Was this helpful? Thank you for your feedback!
-
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.Was this helpful? Thank you for your feedback! -
In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.Was this helpful? Thank you for your feedback!
-
This product is rated IP67, which is different from IPX7. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes. It is also resistant against dust. Dust accumulation around electronics can lead to hardware failure, so the IP67 rating is an extremely beneficial addition to this product.Was this helpful? Thank you for your feedback!
-
If you create a Stereo Pair using the JBL Portable App and you come within range of additional PartyBoost compatible speakers while they are ON, the app will find these speakers. This will break the stereo pair and create a mono PartyBoost group that includes all active speakers that are in proximity. This only happens when the JBL Portable App is actively running on the source device, including when it is running in the background, and when these other speakers are ON. To avoid this scenario, make sure the app is completely closed, without running in the background before coming near any additional PartyBoost speakers that happen to be ON.
NOTE: The Portable App does not need to be running in order to enjoy Stereo sound from two speakers
Was this helpful? Thank you for your feedback! -
The new PartyBoost does not support the previous Connect and Connect+ features. For example: You will not be able to successfully connect the new PartyBoost enabled Flip 5 with a Connect+ enabled speaker like the Pulse 3 or Flip 4. You will not be able to connect the Boombox 2 to the original Boombox speaker.
Was this helpful? Thank you for your feedback! -
1. Connect the first Partyboost speaker with your phone and keep music playing (for best results play music on this speaker for more than 20 seconds before proceeding with the next steps).
2. Press the Partyboost button on the first speaker.
3. Turn on the second speaker that you want to connect in Partyboost mode.
4. Now press the Partyboost button on the second speaker.
5. After a few seconds, both Partyboost speakers should connect and play together.
It can take a few seconds after music is started before sound will be heard from both speakers.
This is also the process for connecting more than two speakers in Party mode, simply turn on the other compatible speakers and press the Partyboost buttons.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09:00 - 17:00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00