How To

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.

Microphone Cleaning (handheld mics)

There are two very important reasons to keep your microphone clean.

1. Hygiene/Germs, especially when a mic is used by multiple people, can unknowingly be spread.
2. Dried spit, dust, dirt and debris can build up in the screen and sponge, negatively affecting the microphones’ ability to accurately pick up and reproduce the voice or instrument.

 

To clean the microphone…

1. Remove/Unscrew the grille from the microphone, turning counter-clockwise.

2. Remove the foam from the inside of the grille.

3. Wash the foam with warm water and dish soap.
4. Clean the grille with any household non-abrasive disinfectant/cleaner.
5. Thoroughly dry both the grille and the foam.
6. Insert the foam into the grill.
7. Screw the grille back onto the microphone, turning clockwise.

 

NOTE: For quality purposes, it is recommended that the screen of the microphone be cleaned once per month when used on a regular basis. For hygienic purposes, when used by multiple people, cleaning is recommended more often, possibly even nightly.

Yes. This headphone has a built in microphone. To answer a call, press the power button which is located on the Left Ear Cup for 1 second. If you wish to hang up the call, press and hold the power button for 2 seconds.

If the wireless mic is out of signal range, you will experience drop outs or no sound. Once range is reestablished, the speaker should automatically detect the mic and resume connection within less than 3 sec. 

When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds. 

If one of the wireless mics is not working, we recommend the following: 

1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound 
 

Below you can see the placements of the microphones on some of our headphone models:

Live Pro+ TWS


Tour Pro+ TWS


Tour One

Make sure both the QuantumENGINE software and the headset's firmware is updated to the most recent version, and that the microphone is plugged all the way in.

While using the Wired Aux Connection, the microphone will be switched off. 

This product features Multi-Point Connection which allows you to be connect to two devices at the same time. Effortlessly switch from listening to music on your portable device to a call from your phone.

To connect to two devices at the same time:

1. Power on your product.
2. Make sure that the device you wish to connect to has the BT settings on and within range.
3. If this is the first time connecting your product, you will notice a flashing LED to indicate that it is searching for a device to connect to. (If this is not your first time, your product will automatically reconnect to the last device it was connected to)
4. Under your BT settings, go to discoverable devices and the product name should pop up within a few seconds. Depending on the device you are using, you may have to tap on the product to complete the connection. 
5.Now that you are connected to the first device, push the BT button on the product to connect to the second device. The product should start searching for the second device by displaying a flashing LED.
6. Go to your BT settings on your second device. The product should pop up on your discoverable devices should pop up within a few moments.

(Please Note: If the product does not show up on your discoverable devices while it is in pairing mode, quickly turn off your BT settings and turn it back on. This will typically result in resetting the BT search in which your product should pop up on discoverable devices within a few moments)


 

If you are experience connectivity problems with Wi-Fi connection, please try to reset all Wi-Fi settings. This can be done by pressing power button for 10 seconds, the power button will quickly flash to indicate it has been reset. After you have reset all Wi-Fi settings, please shutdown the device and pull out the power cable from the wall socket. Put back in the power cable into the wall socket and try do the Wi-Fi setup again.

Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.

1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
 

Try below steps. Attach the charger so the device is charging. While charging: First try to hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds (this resets the Flip 3 to factory settings). If this does not help, press and hold the "Volume +" and "Link" buttons for more then 10 seconds (this will exit demo mode). As a last step, short press on the "Volume -" & "Volume +" & "Phone" buttons. If the device will still not turn on, it has a defect.

Yes, rinse it under a faucet or under the shower, but not under full water pressure.

Voice commands can only be triggered by the user who registered them during setup.

A certain degree of sensitivity is necessary to make the response system function. In some cases, hair or a cap touching the sensor plates can activate the system, even if you do not want it. The solution is to lock the sensor system. Put your finger on the left sensor plate, and hold it there for more than 4 seconds. Now the sensors are locked, and the problem is solved. Unlocking is done the same way.

Tap-hold on the right ear bud forcefully to reconnect heart rate. If this does not work, Hold the middle button to turn off, then back on your headphones.

With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.

Some of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.

See the release notes for app version 4.10.9 below:
- Adding support for TOUR PRO+ TWS and TOUR ONE Global version
- Removing expired DJ’s signatures

This headphone is supported by the My JBL Headphones App.

To install your JBL LINK speaker using Apple iOS... 1. Download the Google Home app. 2. Activate your Bluetooth connection, as it is required for Apple devices. 3. Follow the instructions in the Google Home app.

Sounds like your JBL LINK 10 or LINK 20 has been connected to another Wi-Fi network. It is very simple to reconnect to your Wi-Fi by using the Google Home app. Simply select your Wi-Fi in the app, and you're all set. All information about the speaker and voice teaching is stored in the Cloud, so you do not have to do this again.

We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.

We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.

No, your subwoofer is not defective at all! This is normal and by design of the product after it has been paired for a longer period of time.

There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now. 

No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.

In order to get the earbuds to power on, please remove the plastic film to allow the pins in the charging case to make contact with the contact plates on the earbuds.

1. Ensure that your JBL One app device is less than 10m/33ft from the speaker during the initial set-up.
2. Ensure it is plugged into power and the power LED is illuminated.
3. Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
4. Temporarily relocate either the speaker or router so that they are closer together.  If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
5. Try using a different device with the JBL ONE app installed and connected to your home network.

It is usually not necessary to replace an unresponsive remote control. First, check to see if there is a small plastic tab extending out of the base of the remote control. This is a protective sleeve installed on new remote controls to prevent the battery from draining. Pull this tab to remove the plastic sleeve. The sleeve must be removed before the remote will operate. If the sleeve was removed or not present and the remote control is not working then a new battery should be installed before replacing the remote control. There is a small slide out drawer that houses the battery. The battery type will be either CR2025 or CR2032 for remotes of this size. Replacement batteries are commonly available from most electronic and convenience stores that sell small batteries. Check the number on the original battery and replace it with a battery that uses the same number. These steps will typically solve the problem.

This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.

There are two ways to blow speakers. The first is the one we all know and understand. If you pump 500 watts into a speaker that is only rated at 100 watts, kaboom, it blows up. As a result, very few of us do this. So then why are all of these poor, helpless speakers blowing up? Because of the second reason, under-powering. It's really a misleading term, but let's try to explain. First let's take it to the maximum. Example: You have a 1000 watt speaker and a 100 watt amplifier. The way you like to listen to music requires 300 watts. Typically, you will ask your amp to put out that 300 watts that you want to hear. The amp will do it, but it will clip and distort. Unfortunately, the human ear can't hear distortion until it reaches almost 10%. By that time it's usually too late. The speaker keeps trying to reproduce this distortion that it's not capable or reproducing and eventually it blows (usually the tweeter fails first). If you are blowing speakers with an amp that has a power rating lower than your speakers, you are pushing your amp too far, causing it to clip, and blowing speakers. If you are pushing your system too hard, it is suggested that you realize your systems limitations or recommend that you get a more powerful amplifier. Please realize, if you only buy speakers that will handle more power and not a more powerful amplifier, you won't solve the problem. The speakers will still blow, because it is distortion that is blowing them, not too much power.

Our Control X Wireless speaker has two different patterns for switching on, when using either battery or AC power. When using battery, turning on one speaker in either stereo mode or association mode (4 speakers connected), all will turn on simultaneously, no matter which is primary or secondary. When connected to AC power, switch on the primary speaker in stereo or associated mode, and the secondary speakers will follow. If you have associated speakers stereo or 4 speakers connected, then you have to press primary speaker's power button for more than 2 seconds, then the primary will send signal to secondaries, and they will wake up. It takes approx. 30-60 seconds before all are switched on. If your press it too short (less than 2 seconds), the primary speaker will not "pair" the secondary speakers together. Switch off the primary and start over again.

Some mobile phones, tablet computers or laptop computers will react to the powerful magnetic field from the loudspeaker drive units that are right beneath the top panel. Some have magnetic sensors built in, which means that covers with magnets in the lid can turn the phone ON when the cover lid is opened, and turn it OFF again when the lid is closed. Such phones may turn off if placed on certain portions of the top panel. Other devices are simply sensitive to magnetic fields. You can move the device around on the top of your L8 or L16 speaker, to check if some locations are better than others. The magnetic fields are most powerful near the front panel, where the speaker units are mounted. If you cannot find a location which works, your particular phone, tablet or laptop cannot be used while resting on the top panel of your speaker. There are no reports of damage to any devices because of this phenomenon.

This is most likely due to CEC function. Some our soundbars supports CEC commands from your TV, and if some CEC commands will make the speaker react in a way you do not like, we suggest you disable all CEC functions from your TV. Please note, that your Soundbar will not turn on when your TV is turned on, due to disabling the CEC function.

When you are installing new apps or adding content to your LINK BAR, the system may be a bit slower when dealing with multiple things.
Here is a couple of things you should know.

1. You need a speedy internet connection to download all the content you added.
2. Wait for everything to be finished, then you can enjoy the system without any issues.
3. Reboot LINK BAR after installing all apps. A fresh reboot can help and enhance performance.

If you find yourself encountering audio dropouts or interference coming from your surround speakers when they are not docked on the main unit, here are a couple of tips to try to remedy that.

1. Try moving any wireless routers that are near the sound bar further away.

2. Reboot router so it can auto select a new frequency channel, since the sound bar and router may be on the same channel resulting in audible interferences

3. Re-position the surround speakers so they are closer to the main unit.

4. Re-calibrate the surround speakers

5. Adjust the volume on the sound bar and gradually raise the volume, if driven to hard the sound bar speakers can distort

Yes, rinse it under a faucet or under the shower, but not under full water pressure.

If you are having difficulty with the noise cancelling feature while on your PS4, please check your side tone setting in QuantumENGINE by connecting your Q800 to your PC. Please note that ANC will not work properly if the mic is on and sidetone is greater than 0. We recommend either muting the mic or change the sidetone in the JBL QuantumENGINE to 0. 

We've intentionally designed the flip-up boom mic to stay affixed to the headset. We know from experience that losing or breaking the detachable mic is never fun. Therefore, we designed the mic to fold neatly into the headset - this design also allows the mic to automatically mute when elevated. If you're wanting a detachable mic, please check out the Quantum 100 or the Quantum ONE.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're using the USB dongle, check that the correct playback device is selected under Control Panel > Sound > Playback. Select the proper playback device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Ensure that the correct device is selected as the default device under Control Panel>Sound>Playback. Make sure the on headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.

The JBL Xtreme will no longer appear in the JBL Portable app while using Apple devices with iOS 14 or later installed, due to incompatibility. 
You can continue to use the speaker as normal with these devices through Bluetooth or Aux connection, but it will no longer appear in the app. 
There are currently no plans to release a new Firmware as the JBL Xtreme has been discontinued. 

Let's see what we can try to do to solve your problem.

1. Check if the Privicy-Switch button is OFF (the MUTE button on the LINK BAR).
2. Go to the settings menu, “Device preference --> Google,” check “OK Google” detection is enabled.
3. Make sure there is no objects place on top of the LINK BAR which may block the microphones.

Yes, this is correct. In order to minimize interference between speaker and microphone during telephone conversations, one speaker unit is deactivated.

While the speaker provides a single wireless microphone in the box, it has the ability to work with two wireless microphones. Some units will include Mic A, while others will have Mic B. If you are looking to order the second mic, you must first determine which mic you already have.

 

1. Power on the microphone.
2. Long press the Power button. The mic will power off. Keep pressing the button until the mic shows the version.
   1. 6A08 = Mic A. You will want to order Mic B. Part #050100-000014
   2. 6B08 = Mic B. You will want to order Mic A. Part #02-UMI033-XX0
3. Please call 1-800-336-4JBL (4525) to place your order.

Although both speakers have the same tweeter and woofer, because the Arena 170 has a larger cabinet, it will produce deeper bass. This also means that the Arena 170 can handle more power, versus the Arena 130 speakers. Please see product spec. sheet and/or manual for more details.

Every person has different preferences for wall mounting products. Nevertheless, we tried out varies options and found this to be the place for optimal sound performance.

1. Use the included "Wall-mount guide" that came with your LINK BAR.
2. From the down edge of your TV screen, measure 50mm (using the guide for the screws) or 5 cm or 2 inches depending on the country.
3. It will perfectly align the LINK BAR close to your TV and give the best performance.

Also, you won't have to deal with HDMI cables being too short!

These are our recommendation if you want to place it further down, be our guest!
The sound and performance will still be magnificent!

To power on and pair the headphones, remove the ear tips from the charging case. If this is your first time using the headphones, they will automatically go into pairing mode. You will see the blue and red LED light flash on the RIGHT and LEFT ear as it attempts to pair with your device. Make sure your device is in range and BT settings are ON. The JBL True Wireless Flash X should pop up on your list of discoverable devices within 3-5 seconds, tap and connect. Once connected, you will see a slow blinking blue light below the UA logo on the RIGHT and LEFT Ear. This headphone allows you to use the ear tips in Stereo or Mono mode. If you wish to just use the LEFT or RIGHT ear, simply place the ear tip you do not wish to use back in the charging case.

Try a manual pairing of the headset and the dongle.
Hold the power button in the "On" position for 5 seconds on the headset, and then hold the button on the dongle for 5 seconds. This should force a manual pairing, allowing the PC to again recognize the headset.
Be sure to check multiple USB ports (to confirm it’s not an issue with the USB port).
If the dongle can’t be manually paired either, please contact customer support.
 

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

First time you perform the pairing, it can take several minutes to establish connection. If more than five minutes go by with no result, please switch both units OFF and ON again.

If the two buds lose connection to each other, you can choose to force-pair the main/right bud to the secondary/left bud or the other way around.
For both buds, triple-click the button on one ear bud to pair with the other ear bud.

If you create a Stereo Pair using the JBL Portable App and you come within range of additional PartyBoost compatible speakers while they are ON, the app will find these speakers. This will break the stereo pair and create a mono PartyBoost group that includes all active speakers that are in proximity. This only happens when the JBL Portable App is actively running on the source device, including when it is running in the background, and when these other speakers are ON. To avoid this scenario, make sure the app is completely closed, without running in the background before coming near any additional PartyBoost speakers that happen to be ON.

NOTE: The Portable App does not need to be running in order to enjoy Stereo sound from two speakers

The new PartyBoost does not support the previous Connect and Connect+ features. For example: You will not be able to successfully connect the new PartyBoost enabled Flip 5 with a Connect+ enabled speaker like the Pulse 3 or Flip 4. You will not be able to connect the Boombox 2 to the original Boombox speaker.

If you are experiencing sound fading in and out (pumping) or volume levels changing while playing your instrument, this is known as limiting. The sound being sent into the PARTYBOX may be too loud which will cause the limiter in the speaker to kick in. This can cause the volume levels to dip. This is done to protect the speaker from playing louder than it’s rated output, and it likely means that the instrument input level on the PARTYBOX is set too high. Please perform these steps to calibrate your input level and to prevent pumping:

 

1.  While music is playing via BT or line input, set the volume on the PARTYBOX to a comfortable listening level.
2. Stop playing the music.
3. Turn the instrument/guitar input volume on the PARTYBOX all the way down.
4. Connect the instrument to the instrument/guitar input on the PARTYBOX.
5. Set the volume on your instrument to max.
6. Start playing the instrument and begin turning the instrument/guitar volume on the PARTYBOX up. The instrument should sound perfectly normal without any pumping or swelling. Continue to turn up the volume until you start to notice pumping or swelling. When you hear this, turn the volume back down a little bit until the pumping completely stops. You have now calibrated the input level for that instrument. During this step, as you are turning up, if it gets too loud, turn down the main volume on the PARTYBOX to a comfortable level, and then continue.

You should now use the main volume on the PARTYBOX to set the loudest volume for your instrument and can use the volume control on your instrument to adjust the level up or down.

 

NOTE: Whenever connecting a different instrument, you will likely have to repeat this process as all instruments (guitar pickups) have slightly different output levels. This is how you can ensure maximum performance out of your PARTYBOX.

Click here for a list of How To videos about the PartyBox 1000!

PARTYBOX 110
Software Update Release Notes
------------------------------------------------------------------------
Version:  1.35.0
Release Date:  September 19, 2022
Release Media:  OTA (over the air) Automatic Upgrade

What's New

What’s New:
The new Software version will enable Party mode across PartyBox 310 & PartyBox 110 series. 
Stereo mode will still only work when 2 PartyBoxes of the same model are connected.