How To
How To
1217 results
-
Press the power button located on the bottom of the Right Ear cup. If this is your first time using the headphones, it should immediately start looking for a device to connect to. Make sure that the device that you are trying to connect to is in pairing mode. The JBL JR300BT should display on your discoverable devices within 2-5 seconds. If the headphones have not successfully connected to the device, press and hold the Bluetooth button located next to the Power button on the Right Ear Cup for 2 seconds. As the headphones go into pairing mode, they should connect to your device within 2-5 seconds.Was this helpful? Thank you for your feedback!
-
The Synchros Chrome is actually the Synchros S500 in chrome-plated version. On the right ear cup, you will find two ridges. These are there to make it possible to remove the disc that covers the batteries. You just position your fingernails against the ridges, to turn the disc counter-clockwise, against a small notch resistance. The Chrome is not painted, but plated. This means that the material is now thicker, and the lid can be rather difficult to remove, because the locking notches are squeezed into position. There is no other way than to put pressure on the ridges, press downward and in a counter-clockwise direction at the same time, and press until the notches, or claws, finally let go, and the lid rotates into open position, when it will fall off. If the lid does not budge, it may be necessary to use some kind of tool, but that can damage the chrome surface. In extreme cases, it may have to go to service.Was this helpful? Thank you for your feedback!
-
The track control button is located in the center of the inline microphone in between the volume control. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward.Was this helpful? Thank you for your feedback!
-
The REFLECT MINI BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
The Reflect Contour BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
-
If you want to skip your track forward, simply press and hold the top button on the inline microphone. If you want to skip the track backward, press and hold the bottom button until you hear the track skip backward. You typically hold the button for 1-2 seconds to advance to the next track or to go backwards.Was this helpful? Thank you for your feedback!
-
Press and hold the RIGHT center button for 1-2 seconds.Was this helpful? Thank you for your feedback!
-
Tap and hold the left earpiece for 2 secondsWas this helpful? Thank you for your feedback!
-
The E65BTNC noise cancellation button is located on the bottom Right ear cup. To turn the Active Noise Cancellation on, press and hold the button (Located next to the Bluetooth button) for 2-3 seconds or until you hear the confirmation audio tone. To turn off the noise cancellation, press and hold for 2 seconds or until you hear the audio tone powering off. A white LED next to the button lights up when NC is on.Was this helpful? Thank you for your feedback!
-
The DUET NC noise cancellation button is located on the bottom Right ear cup. To turn the Active Noise Cancellation on, press and hold the button (Located next to the Bluetooth button) for 2-3 seconds or until you hear the confirmation audio tone. To turn off the noise cancellation, press and hold for 2 seconds or until you hear the audio tone powering off. A white LED next to the button lights up when NC is on.Was this helpful? Thank you for your feedback!
-
By pressing and holding the Bluetooth and the Volume PLUS buttons at the same time. The software version is shown in the display.Was this helpful? Thank you for your feedback!
-
When playing music: one click is Pause or Play. Two clicks skips to next track. Three clicks skips back to start of track or previous track. At all times, hold the button to start voice-activated phone functions. For telephone use: one click to accept a call, two clicks to end the call.Was this helpful? Thank you for your feedback!
-
Unplug the power cord from soundbar. While holding down the VOLUME + button, plug the power cord into the soundbar. A green LED, followed by a blue LED will light up, after which the soundbar will go into standby. The SB150 is now reset.Was this helpful? Thank you for your feedback!
-
For headphones with Version 4.0 of the Firmware, the first update will be done via USB cable, and after the first update, all subsequent updates will be delivered over the air. For headsets with version 5.0 of the firmware, all updates will be delivered over the air, via the appWas this helpful? Thank you for your feedback!
-
When docked and connected to the harness, the BASSPRO GO can be used as a powered subwoofer or a full-range car audio speaker. It receives it’s audio source from the head unit via the wiring harness and it’s power from the car battery. Bluetooth is not active.
When undocked/portable and removed from the harness, it can no longer be used as a powered sub. It is strictly a full-range portable Bluetooth speaker system. It receives it’s audio source from the Bluetooth input only, and receives it’s power from the internal battery.
Was this helpful? Thank you for your feedback! -
You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of musicWas this helpful? Thank you for your feedback!
-
Approximately 2.5 hours. This depends on the actual charger used, and its capacity in Amperes.Was this helpful? Thank you for your feedback!
-
The surround speaker takes up to 4 hours to fully charge.Was this helpful? Thank you for your feedback!
-
Any conversation or search history is stored in the cloud via your Google account and is saved until you choose to delete it. JBL LINK speakers do not keep or store any data locally.Was this helpful? Thank you for your feedback!
-
The cable is approximately 125 cm long.Was this helpful? Thank you for your feedback!
-
You can have 3 smart devices connected at the same time and by pressing play on either one of the sources (smart devices) will start streaming music. The speaker can remember up to 8 paired smart devices and when this buffer is full it will release the first added device in connected sequences. Resetting the speaker will also clear this buffer.Was this helpful? Thank you for your feedback!
-
All three devices supports up to 3 Bluetooth connections at the same time. However, only one can play music while connected, if one of the other paired devices starts playback, it will interrupt the music that is currently playing, and begin playing from the second or third connected device.Was this helpful? Thank you for your feedback!
-
Up to 3 devices can be paired to the BOOST TV at one time.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)