How To
How To
1217 results
-
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
To ensure the best accuracy, it is important that you are using the proper size and the headphones securely fit in the ear. Please reference FAQ: How do I find the proper fit? to make sure you are wearing them correctly. You should also make sure that the enhancers are properly installed on the ear buds so that material is fully stretched over the bud and the window for the heart rate (HR) sensor is not covered. Please reference FAQ: How do I switch enhancer sizes? for more guidance. Once you've found your ideal size and ensure they're installed correctly, make sure the HR sensor is on. When it is on, you will see a green light on the LEFT ear bud and should hear the audio prompt stating, “Heart Rate sensor on”. For best results, insert the earphone into your ear so that the green heart rate sensor on the LEFT ear bud is fully hidden inside the ear (behind your tragus). Double check that the ear bud is touching the back of the bowl of your ear for the most accurate signal - this is often times achieved by using the largest size that fits comfortably in your ear. Lastly, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone loop and your ear. You should hear the audible alert telling you if the ear bud needs to be adjusted if it is unable to retrieve a proper reading on your heart rate. Heart Rate accuracy can vary depending on the type of exercise you are performing; it is recommended for steady state endurance-oriented activities to ensure best accuracy. While the technology is state-of-the-art, there are limitations that may cause some readings to be inaccurate under certain circumstances. These circumstances include physical characteristics, fit, and the type of activity as outlined above. The heart rate monitor data is not intended to be used for medical purposes, nor is it intended to diagnose, treat, cure or prevent any disease or condition.Was this helpful? Thank you for your feedback!
-
During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to activate pairing mode. Now set your device to scan for Bluetooth devices. It will find the BOOST TV and allow you to pair to it.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to open for new pairing.Was this helpful? Thank you for your feedback!
-
Swift Pair is the newest way to pair your Bluetooth peripherals Windows 10, version 1803 or above.
Steps:
1. Put the Bluetooth peripheral in pairing mode
2. When the peripheral is nearby, your Windows device will show a notification
3. Selecting “Connect” starts pairing the peripheral
4. When the peripheral is no longer in pairing mode or is no longer nearby, your Windows device will remove the notification from the Action Center
Was this helpful? Thank you for your feedback! -
Simply hold Bluetooth button on the remote and once its start flashing, on your device go to your Bluetooth settings and look for the gtr amp and pair it.Was this helpful? Thank you for your feedback!
-
The SB450 soundbar is paired to the subwoofer right out of the box. If the 2 parts are not already paired together, simply press the Pairing buttons on the rear panel of both products and they will connect with each other.Was this helpful? Thank you for your feedback!
-
Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.Was this helpful? Thank you for your feedback!
-
Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show "DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.Was this helpful? Thank you for your feedback!
-
To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.Was this helpful? Thank you for your feedback!
-
Power on the Soundgear and press and hold the Bluetooth located next to the power button on the right arm. Once you press the the bluetooth button, you will see a fast blinking LED light as it attempts to pair to a different device. You will also hear the audible chime as it attempts to Make sure the device you are attempting to connect to is on and in pairing mode. The JBL Soundgear should be displayed on your discoverable devices within a few seconds. Choose the JBL Soundgear and you should now be connected!Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)