How To
How To
1217 results
-
The UA Sport Wireless Heart Rate must be charged with a micro USB charger that is provided in the packaging. You will find the USB outlet located on the bottom left side of the inline microphone. There will be a small rubberized window that you can slide up and over to expose the outlet. After plugging in the headphones, you will see a solid red light appear at the bottom of the inline microphone. Once the headphones are fully charged, the red light will turn off. It typically takes less than 2 hours of charging time to receive the 5 full hours of audio playback.Was this helpful? Thank you for your feedback!
-
Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.Was this helpful? Thank you for your feedback!
-
The firmware version of the headphone will be displayed in the settings page of the app.Was this helpful? Thank you for your feedback!
-
We recommend cleaning the earphones with audio or electronic wipes.Was this helpful? Thank you for your feedback!
-
You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.Was this helpful? Thank you for your feedback!
-
To clean yurbuds, remove the enhancers (tips) from earphones and wash with warm, soapy water. Do not use anything containing alcohol. Completely dry the enhancers and reposition on the earphones, as shown in the Quick Start guide: Left bud between 3:00 and 4:00 position Right bud between 8:00 and 9:00 positionWas this helpful? Thank you for your feedback!
-
• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.Was this helpful? Thank you for your feedback!
-
• Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.Was this helpful? Thank you for your feedback!
-
To set up and enjoy all the features of your UA Sport Wireless Heart Rate, you’ll need to connect it to your phone using the UA Record™ mobile app. Select the UA Sync icon in the upper right hand corner of the dashboard. Tap on “UA Sport Wireless Heart Rate”. Follow the on-screen instructions to finish setup. Once connected, the headphones will live under My Apps and Devices. Here, you can access your headphones' settings to check your battery level, current heart rate, and help.Was this helpful? Thank you for your feedback!
-
- Visit App store and download ‘Amazon Alexa’ App.
Was this helpful? Thank you for your feedback! -
To pair the JBL LIVE headphones the first time, switch the headphone on, look for the blinking blue light indicating pairing mode. Switch on Bluetooth on your source device, find the JBL LIVE headphones in Settings > Bluetooth and confirm pairing. To pair the JBL LIVE headphones from the second time onwards, or to link them with a different device, press and hold the power button until the blue flashing light is visible.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are completely shut off and proceed to press and hold the power button for 4-6 seconds. You will see the LED indicator light flash red and blue when the headphones are in paring mode. Make sure that Bluetooth is enabled on your listening device and look for “JBL Reflect Response” in the Bluetooth device list. Select “JBL Reflect Response” to connect. After the headphones are connected with a listening divine you will not need to reconnect them, your device should automatically connect to the headphones when both items are on.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)