How To

Support Overview / How To

How To

1202 results
  • Can I place my Flip3 in the bathroom, where it is humid, and it may be splashed with water?
    Yes, steam and drops of water in a bathroom are fine.
  • Can I place my Xtreme in the bathroom, where it is humid, and it may be splashed with water?
    Yes, steam and drops of water in a bathroom are fine.
  • Can I place or answer telephone calls with my JBL LIVE headphones?
    Yes, you can use them for telephone conversations in both Bluetooth and wired mode when paired with a smart device. 
  • Can I play and charge my headset at the same time?
    Yes, you can play game either wired or wirelessly while using USB-C charging cable.  
  • Can I program my TV remote to the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?
    Yes. Out-the-box the JBL Bar series soundbar recognizes volume and mute controls from the most common TV remote controls. The JBL Bar series has IR learning. You can use this feature to teach the soundbar to response to your TV's remote control as well.
  • Can I record directly from the 208P?
    Yes, use the MONITOR OUT sockets (1/4” and RCA are available on 208P, RCA on ONE) to feed into a recording device. Please note that these outputs are volume controlled, so set the volume correctly, depending on the sensitivity of the recording device.
  • Can I replace the ear pads on my Everest 700 or Elite 700 headphones?
    It is possible to replace the ear pads, but there are details to consider. On Elite 700: The ear pads are held in place by a plastic plate with claws, and some of the claws will most likely break off when you remove the pad. You do this by grabbing under the edge where the fabric ends, then pulling hard outward. The claws will eventually let go, and some of them will break off, rattling inside the ear pod. The only way to get them out is to unscrew the speaker plate, lift it up, and shake out the broken-off claws. The new pads are simply centered over the speaker plate, and the claws pressed into the holes with a firm pressure. On Everest 700: The ear pads are glued into position with double-adhesive tape. Pull the old pads off with a forceful, steady pull, until the glue lets go. Remove the protective layer on the new pads, and carefully position them correctly before pressing home all the way around the edge.
  • Can I replace the ear pads on my T-series headphone?
    Yes, the ear pads are replaceable by owner. The pads can be purchased as spare parts from the service center, or purchased directly from the JBL spare parts web shop, when opened.
  • Can I replace the ear pads on the Everest 310/710 headphones?
    No, the pads are glued to the headphone body, and must be replaced by a service technician.
  • Can I reset my Control X Wireless?
    Yes, on the master speaker (the one with playback buttons), simply press the Reverse and Forward Play buttons at the same time for 3 seconds. Please note that after you have performed the reset procedure, master and secondary speakers are no longer connected. Go to the owner's manual page 4, the section "speaker association", to pair the secondary and master again.
  • Can I reset my JBL Authentics L8 or L16, to factory settings?
    Yes it is possible to reset your speaker. The reset will remove all Bluetooth pairings and WiFi network settings. In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash. Your JBL Authentics L8 or L16, are now back to factory settings. Please reconnect the speaker to your WiFi network again.
  • Can I share TV sound through JBL Connect using SB450?
    You can only share the sound via JBL Connect through Bluetooth connected devices. TV sound is not permitted as it would cause lip-sync issues.
  • Can I still use my E45BT even if the battery is dead?
    Yes, the E45BT headphones also have an detachable audio cable that you can plug into the headphones. The plug is located at the bottom of the right ear cup.
  • Can I stream Google Chromecast via my PC to Control Xstream?
    Yes, Control Xstream is a Chromecast device that allows you to cast music content via your Chrome browser. However, the JBL Control Xstream is not made for video purposes, because there will be delay between sound and image.
  • Can I stream music via Bluetooth and Wi-Fi from my device simultaneously?
    Yes. The Google cast function works independent to that of Bluetooth, therefore you are able to Bluetooth connect to another device while casting audio to the JBL Playlist simultaneously. This feature is applicable on smartphones, tablets/iPad, and Bluetooth capable computers.
  • Can I submerge the speaker into water or any liquid?
    You should not submerge the speaker into any water or liquid.
  • Can I swim with these headphones?
    No. These headphones are not waterproof. Swimming with these headphones will cause significant and irreversible damage.
  • Can I switch the display completely off on Pulse 2?
    Yes, although this is not mentioned in the owner's manual, it can be done by pressing and holding the light effect button for more than two seconds.
  • Can I take phone calls with the E25BT headphone?
    Yes, the E25BT features a three button microphone which enables you to pause/play, skip tracks and answer and hang up phone calls.
  • Can I take phone calls with the JBL Duet Mini BT headphone?
    Yes, the JBL Duet Mini features a three button microphone which enables you to pause/play, skip tracks and answer and hang up phone calls.
  • Can I take phones calls with the E45BT headphones?
    Yes, the E45BT headphones allow you to switch seamlessly from your music on your portable device to your phone. The controls are located on the Right ear cup which features your volume control and pause and play which is located in the center of the controls. The center button will allow you to answer and hang up phone calls .
  • Can it be connected to a wall power outlet?
    Yes. A usb wall adapter would be required.
  • Can I turn the Heart Rate sensor off and still use the Under Armour Sport Wireless Heart Rate headphones for audio?
    You can turn the Heart Rate sensor off and still use the headphones for audio by placing your finger on the right earpiece for 3-4 seconds. You will hear an audio prompt stating, “Heart Rate disconnected” which will turn the Heart Rate sensor off. If you wish to turn the sensor back on, simply place your finger on the RIGHT earpiece again for 3-4 seconds until you hear the voice prompt stating that the Heart Rate sensor has been turned back on.
  • Can I use 2 JBL Boombox speakers in Stereo?
    Yes, from within the JBL Connect App, when you have 2 JBL Boombox speakers connected, set them in Stereo Mode. When you add a 3rd ( or more ) JBL Boombox speakers, they will automatically revert back to Party mode
  • Can I use a 3rd party wall-mounting system?
    Yes, just be aware that you are responsible for correct installation when using 3rd party wall mounts. The included wall-mounting kit in the box fits perfectly and is good for outdoor or indoor use.
  • Can I use an in-ceiling speaker as an in-wall unit or vice versa?
    No, in-ceiling speakers cannot be used in the wall due to speaker dimensions. A wall is not deep enough to accommodate the depth of an in-ceiling speaker. For in-wall speakers, you can install them in the ceilings without any depth issues. However, for quality listening, we recommend using architectural speakers according to their intended purpose.
  • Can I use Bluetooth for my JBL Playlist speaker?
    Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Playlist also offers a Bluetooth connection and an AUX input
  • Can I use Bluetooth with my Control Xstream
    Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Control Xstream also offers a Bluetooth connection and an AUX input
  • Can I use both Amazon Alexa and the Google Assistant with my JBL LIVE headphones?
    Yes, both voice assistants are supported by the JBL LIVE headphones.
    Amazon Alexa or Google Assistant must be selected as the default voice assistant through the My JBL Headphones app.
    The two voice assistants cannot be used simultaneously. You can always change your default voice assistant through the My JBL Headphones app.
  • Can I use both Windows and Apple computers to update my Everest headphones?
    The EVEREST models 100, 300 and 700 are all updated with the HID (Human Interface Device) tool, available in the download section for each model. This tool works with Windows computers only. The EVEREST ELITE models are updated with a USB tool available on the special Everest web page. This tool is available in both an Apple MAC OS version and a Windows version. This USB tool update is used for the first production run of ELITE models ONLY, and only once! All later production runs, and all updates after this first USB update, will take place wirelessly through the My JBL Headphone app, made for iOS and Android.
< 1 ... 3 4 5 6 7 ... 41 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a support agent
Call us now at: (800) 336-4525

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat With Us

Chat With Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)