How To

Support Overview / How To

How To

1217 results
  • DSP 4086 Tuning Software Crashing/Not Responding

    If your DSP Tuning Software is not responding properly or is crashing, it is likely because the proper USB driver has not yet been installed.  There is an easy fix for this, and it does not require you to uninstall anything.

     
    1. If the tuning software is open, close it.
    2. Go back to your software install files and double-click on “USB Driver”.

    NOTE: Make sure to allow it to make changes to your computer if your anti-virus software requests it.

    1. After the driver is installed, reopen the software.  Your problem should be resolved.
  • Do you have to be connected bluetooth for the calling features to work?
    Yes. Pair your device with the speaker via bluetooth.
  • Do you have replacement cables available for my Everest headphones?
    Cables and other spare parts for EVEREST can be obtained from either the distributors or from authorized service centers. Please contact Harman Customer Support to get the necessary contact details.
  • Do you deliver overseas?
    We do not ship internationally.
  • Do the UA Train headphones support AptX low latency?
    No. UA Train does not support AptX™ and AptX HD™ audio codecs.
  • Do these headphones have volume control?
    Yes, the Reflect Aware features a three button inline microphone that allows you to control the volume.
  • Do the normal BT models have voice prompt, or can it be changed?
    Yes , all 5 models have voice prompts. The Elite models have the added option of turning off the voice prompts in the settings menu of the app. The Everest 300 and 700, as well as the successors 310 and 710, have the option of choosing between voice prompts and tone prompts. This is how you do it: Switch the headphones ON. Press and hold the Shareme and the Volume Plus buttons for about two seconds. Switch the headphones OFF. You will now hear the OFF prompt having changed to the prompt you did not use before, and you will hear this one until you change it again.
  • Do the Flip 4 and Charge 3 float in water?
    No, the IP waterproof specification means that these speakers can be immersed in water 1 m deep for 30 minutes. It does not mean that they can float, so please be careful. If dropped, they will sink to the bottom.
  • Do the Everest Series headphones support AAC or aptX?
    Sorry, neither AAC nor aptX are supported.
  • Do the Everest headphones need to be fully charged before attempting the update?
    It is not a bad idea to have the headphone charged before updating, but only if it is completely empty will there be any difference. To update via cable, a USB cable connection must be established between the headphone and the computer, and since the cable is also used for charging, there will be power to the headphone as long as it is connected to the computer. If the battery is depleted, it may be necessary to wait a little while, until a basic level of charging has been reached. Please note that the ELITE models with the most recent software permit wireless upgrade, directly from the control app on a smartphone. In this case, it is of course necessary to have power enough in the battery to sustain the whole upgrading process, since it takes place without cable.
  • Do the Everest headphones have to be powered on before you connect them to the computer?
    No, the tool will tell you to switch them ON when necessary.
  • Do the Everest and Everest Elite headphones support AAC or aptX?
    Sorry, neither AAC nor aptX are supported.
  • Do JBL Club Headphones Support aptX?
    JBL Club headphones do not support aptX. There are a number of different platforms available and our choice was driven by the one that provides the combination of best sound quality and user experience. The platform that we have selected perfectly fits the requirements of the JBL Club series including voice integration and audio customization whilst supplying the Hi Res-certified headphones with the quality of audio they deserve.
  • Do I need to link my Google account to my JBL LINK 10, 20, 300 or 500?
    JBL LINK speakers require a Google account to operate. Your search history on the JBL LINK speaker will appear in your Google account's search history. Also, if you give the JBL LINK speaker permission, it may access your data saved in other Google services, like Calendar and Gmail to answer questions you ask.
  • Do I need to close the USB cap for the speaker to be waterproof?
    Yes, it is needed to close the USB cap completely for waterproof.
  • Do I need to charge from a certain kind of charger, or can I use all USB sockets?
    Each headphone is shipped with a micro USB charging cable. USB is the only way to charge the headphones, and all normal USB chargers may be used.
  • Do I need to calibrate the head tracker sensor?
    The head tracker in the Quantum ONE uses your movements to calibrate the sensors. You can speed up the calibration process by doing the following: * Imagine that the headphone is a standard cube with 6 faces (Front, Back, Left, Right, Top, Bottom) * Orient the headphone so that it is sitting on each face of "the cube" sequentially. For example, start with the headphone positioned normally (bottom face of the cube down). Then rotate it so that the right side of the cube is facing down. Then continue through the rest of the faces of the cube. * Hold the headphone in each position for 1 second * Once all the faces of the device have been rotated, set the headphone down on a stationary surface for 2 or 3 seconds.
  • Do I need the App to update the software in the Everest Elite headphones
    For headphones with Version 4.0 of the Firmware, the first update will be done via USB cable, and after the first update, all subsequent updates will be delivered over the air. For headsets with version 5.0 of the firmware, all updates will be delivered over the air, via the app
  • Do I have the option to control the volume from the detachable inline remote cable?
    Unfortunately, there is no volume control on the inline microphone. You have the options to answer phone calls, skip tracks and pause and play.
  • Do I get charged for delivery of each item?
    You will not be charged for ground shipping. Expedited shipping costs are based upon total weight and service availability.
  • Does Trunote work only when ANC is ON?
    Yes, ANC needs to be ON.
  • Does Trip have to be plugged into power to work?
    No. This product has a rechargeable battery.
  • Does this speaker have an Aux Input?
    This speaker does not have an Aux Input, so no analog connection is possible.
  • Does this headphone support JBL QuantumSURROUND?
    The JBL Quantum 100 is not equipped with JBL QuantumSURROUND. You can consider to purchase the JBL Quantum 300, which comes with a USB dongle and access to JBL QuantumENGINE. 
  • Does this headphone support JBL QuantumSURROUND?

    The JBL Quantum 200 is not equipped with JBL QuantumSURROUND. You can consider to purchase the Quantum 300, which comes with a USB dongle and access to JBL QuantumENGINE. 

  • Does this headphone have a microphone?
    The Inspire 100 series does not feature a microphone.
  • Does this headphone feature volume control?
    Yes, this headphone features a three button microphone that features volume control, track control, and can receive phone calls.
  • Does this headphone feature the automatic shut off?
    No, the Reflect Mini BT does not feature the automatic shut off.
  • Does the Xtreme has the same sound with and without AC power connected?
    If you are playing on battery only, you may experience slightly lower bass level and dynamics near maximum volume. If you are AC connected and playing via your Xtreme speaker, you will hear an increase in bass performance. The reason that bass performance is lowered when playing on battery is to reduce power consumption for you to have longer playing time from your Xtreme speaker.
  • Does the Wi-Fi indicator on the front of JBL Playlist, has to be at full signal to work?
    If the Wi-Fi indicator has all 3 LED lights on, then the signal to the speaker is extremely good, and if only 2 LED light up, then the signal will be good. If you only have 1 LED light or No LED light we suggest moving the speaker to a different location for a better Wi-Fi signal and better audio experience.
< 1 ... 30 31 32 33 34 ... 42 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a support agent
Call us now at: (800) 336-4525

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat With Us

Chat With Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)