How To
How To
1217 results
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.Was this helpful? Thank you for your feedback! -
To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
On the soundbar, press and hold the power and source button for more than
10 seconds.
Please note this procedure will revert ALL settings back to factory default.Was this helpful? Thank you for your feedback! -
You can reach out to the Under Armour Customer Service in the USA by phone at 1.800.377.9952 or by e-mail at ua.jblsupport@harman.com.Was this helpful? Thank you for your feedback!
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)