JBL Tune 110BT
Trådløse ørepropper
Sold from 2017 until now
Getting started with your JBL Tune 110BT
Documents & Downloads
Product Specifications
- Driver size (mm)
- 8.6
- Driver sensitivity at 1kHz/1mW (dB)
- 96dB SPL/1m@1kHz dB v/pa
- Dynamic frequency response range (Hz)
- 20 Hz - 20 kHz
- Impedance (ohms)
- 16.0
- Number of drivers per ear
- 1.0
- Headphone cable length (cm)
- 80.8
- Headphone cable length (ft)
- 2.65
- Weight (g)
- 16.2
- Weight (oz)
- 0.57
- Bluetooth profiles
- HFP v1.5, HSP v1.2, A2DP v1.2, AVRCP v1.5
- Bluetooth frequency
- 2.402GHz-2.48GHz
- Bluetooth transmitted modulation
- GFSK, DQPSK, 8-DPSK
- Bluetooth version
- 4.0
- Charging time (hours from empty)
- 2.0
- Maksimum spilletid (timer)
- 6.0
- Maximum talk time (hours)
- 6.0
- Bluetooth
- Ja
- Built-in Microphone
- Ja
- Flat Cable
- Ja
- Hands Free Call
- Ja
- JBL Pure Bass Sound
- Ja
- Rechargable battery
- Ja
- Speed charge
- Nei
- Wireless
- Ja
En enkel løsning med fantastisk lyd.
JBL TUNE110BT ørepropper har JBL Pure Bass-lyd og er en enkel trådløs løsning for hverdagsbruk, kombinert med muligheten til å ringe eller ta imot anrop handsfree, samt seks timers batterilevetid. Tenk deg ørepropper som lades opp på bare to timer, leveres i seks flotte farger, har en flat, flokebestandig kabel og er lette nok til å ha på uten ubehag i time etter time. Og når du kombinerer det med magneter som sikrer at øreproppene ikke dingler når de ikke er i bruk, den flokebestandige kabelen og behagelige ergonomiske ørepropper og nakkebånd, er det lett å forstå at JBL TUNE110BT kan bli en uunnværlig del av din musikkelskende hverdag.
FAQs & How-Tos
-
This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.Was this helpful? Thank you for your feedback!
-
Yes, the T110BT features a three button inline microphone which allows you to pause/play skip tracks, answer calls and control the volume.Was this helpful? Thank you for your feedback!
-
There are several easy ways to prevent damage to your headphones, and please follow the steps below.
-
If the USB port has a cover, please always have it covered, except when charging.
-
Always be sure the USB port and connector are dry before connecting to charge.
-
Do not allow any oils, stains, sweat, or corrosive materials to contact the charging port. It will eventually damage the port.
-
Do not damage or block the USB port. For example, do not force it in if you have trouble inserting the USB connector into the port. Instead, examine the port and remove foreign substances that might be inside or blocking the port.
Was this helpful? Thank you for your feedback! -
-
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.Was this helpful? Thank you for your feedback! -
To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.Was this helpful? Thank you for your feedback!
-
This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+47 21 93 29 30
Monday - Friday: 09.00-17.00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00