JBL Tune 520BT

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.

The way you remove and change the ear cushions on your headphones varies from on-ear headphones to over-ear headphones and also from product to product.

When removing and replacing the ear pads you will see the following examples:

 

Removing on-ear headphones

Pull the ear cushion as you see on the below picture.

 

The ear cushion will slide out of the hole when you have pulled it enough, which is the case with the picture below.

 

When the earpad is completely removed it will look like the picture below.

 

Removing over-ear headphones

Pull the entire earpad off. You need to pull the material that is placed on your ear. Pull carefully so the plastic hooks does not snap off or break. When you have pulled the earpad of it will look like the picture below.

 

Replacing new on-ear earpads

Align the cushion with the hole all the way around the ear pads.

 

Replacing new over-ear earpads

Align the plastic hooks which are marked on the left side on the picture below with the holes that are marked on the right side of the picture.

If not pre-installed on your Android device, visit your App store to download the ‘Google Assistant’ App.

After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.

Step 1

 
Follow the steps to connect and pair “JBL XXXX-LE” (depends on your model) with your devices.
Once set up is complete, you will see the below screen:

Step 2

PLEASE NOTE: In order to verbally interact with your Google Assistant via the headphone you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under: Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.

Visit your App store to download the ‘Google Assistant’ App.

After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.

Step 1

 
Follow the steps to connect and pair “JBL XXXX-LE” with the Google Assistant App, the name will depend on your model.
Once set up is complete, you will see the below screen:

Step 2

PLEASE NOTE: To verbally interact with your Google Assistant via the headphone, you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.
 

This product features Multi-Point Connection which allows you to be connect to two devices at the same time. Effortlessly switch from listening to music on your portable device to a call from your phone.

To connect to two devices at the same time:

1. Power on your product.
2. Make sure that the device you wish to connect to has the BT settings on and within range.
3. If this is the first time connecting your product, you will notice a flashing LED to indicate that it is searching for a device to connect to. (If this is not your first time, your product will automatically reconnect to the last device it was connected to)
4. Under your BT settings, go to discoverable devices and the product name should pop up within a few seconds. Depending on the device you are using, you may have to tap on the product to complete the connection. 
5.Now that you are connected to the first device, push the BT button on the product to connect to the second device. The product should start searching for the second device by displaying a flashing LED.
6. Go to your BT settings on your second device. The product should pop up on your discoverable devices should pop up within a few moments.

(Please Note: If the product does not show up on your discoverable devices while it is in pairing mode, quickly turn off your BT settings and turn it back on. This will typically result in resetting the BT search in which your product should pop up on discoverable devices within a few moments)


 

This headphone is supported by the My JBL Headphones App.