How To
How To
-
There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now.Was this helpful? Thank you for your feedback!
-
No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.Was this helpful? Thank you for your feedback!
-
Try to move the microphone closer to the sound source and adjust it for a better angle. You should also try to decrease the microphone volume to an appropriate level by turning the volume down.
Finally, try to enable the Dynamic Range Compressor (DRC) option in the QuantumEngine to lower the chance of distortion.
Was this helpful? Thank you for your feedback! -
Try to move the microphone closer to the sound source and adjust it for a better angle. You should also try to increase the microphone volume to an appropriate level by turning the volume up.
Finally, try to increase or decrease the microphone gain level if the sound is distorted.Was this helpful? Thank you for your feedback! -
If your parcel is showing signs of damage upon delivery, we recommend that you refuse to accept it.
The parcel will then be returned to our warehouse, and you will automatically receive a refund.
If you already accepted your parcel, please take pictures of the damage(s) before opening the parcel.
We hope that the product(s) you have ordered are without any damage.
If the product(s) are damaged, please contact Customer Support as soon as possible, and no later than 2 days after receival of the parcel as we have a short window to process claims with our delivery partner.
Please note that you must keep all packaging, including the brown shipping box, while our Customer Support team is opening a claim with our delivery partner.
Was this helpful? Thank you for your feedback! -
We use a sophisticated vetting process to ensure that your image does not contain copyrighted, protected, sexual, suggestive, offensive or inappropriate elements. This includes words and messages. If these algorithms are triggered, your order is automatically cancelled. Please try again with a different image or wording.Was this helpful? Thank you for your feedback!
-
- Ensure that your JBL One app device is less than 10m/33ft from the speaker during the initial set-up.
- Ensure it is plugged into power and the power LED is illuminated.
- Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
- Temporarily relocate either the speaker or router so that they are closer together. If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
- Try using a different device with the JBL ONE app installed and connected to your home network.
Was this helpful? Thank you for your feedback! -
It is usually not necessary to replace an unresponsive remote control. First, check to see if there is a small plastic tab extending out of the base of the remote control. This is a protective sleeve installed on new remote controls to prevent the battery from draining. Pull this tab to remove the plastic sleeve. The sleeve must be removed before the remote will operate. If the sleeve was removed or not present and the remote control is not working then a new battery should be installed before replacing the remote control. There is a small slide out drawer that houses the battery. The battery type will be either CR2025 or CR2032 for remotes of this size. Replacement batteries are commonly available from most electronic and convenience stores that sell small batteries. Check the number on the original battery and replace it with a battery that uses the same number. These steps will typically solve the problem.Was this helpful? Thank you for your feedback!
-
This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.Was this helpful? Thank you for your feedback!
-
There are two ways to blow speakers. The first is the one we all know and understand. If you pump 500 watts into a speaker that is only rated at 100 watts, kaboom, it blows up. As a result, very few of us do this. So then why are all of these poor, helpless speakers blowing up? Because of the second reason, under-powering. It's really a misleading term, but let's try to explain. First let's take it to the maximum. Example: You have a 1000 watt speaker and a 100 watt amplifier. The way you like to listen to music requires 300 watts. Typically, you will ask your amp to put out that 300 watts that you want to hear. The amp will do it, but it will clip and distort. Unfortunately, the human ear can't hear distortion until it reaches almost 10%. By that time it's usually too late. The speaker keeps trying to reproduce this distortion that it's not capable or reproducing and eventually it blows (usually the tweeter fails first). If you are blowing speakers with an amp that has a power rating lower than your speakers, you are pushing your amp too far, causing it to clip, and blowing speakers. If you are pushing your system too hard, it is suggested that you realize your systems limitations or recommend that you get a more powerful amplifier. Please realize, if you only buy speakers that will handle more power and not a more powerful amplifier, you won't solve the problem. The speakers will still blow, because it is distortion that is blowing them, not too much power.Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speaker has two different patterns for switching on, when using either battery or AC power. When using battery, turning on one speaker in either stereo mode or association mode (4 speakers connected), all will turn on simultaneously, no matter which is primary or secondary. When connected to AC power, switch on the primary speaker in stereo or associated mode, and the secondary speakers will follow. If you have associated speakers stereo or 4 speakers connected, then you have to press primary speaker's power button for more than 2 seconds, then the primary will send signal to secondaries, and they will wake up. It takes approx. 30-60 seconds before all are switched on. If your press it too short (less than 2 seconds), the primary speaker will not "pair" the secondary speakers together. Switch off the primary and start over again.Was this helpful? Thank you for your feedback!
-
If your tracking has no updates for more than 3 days, please contact Customer Support for further assistance.
Please note that larger products, such as most party boxes, soundbars, and subwoofers will be delivered via a lorry on a pallet with our delivery partner for large shipments, DB Schenker. If so, you will receive an email from DB Schenker from which you need to schedule a delivery appointment. For more information about shipments via lorry on a pallet, see here: https://support.harmanaudio.com/gb/en/customer-service/large-shipments.htmlWas this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00