How To

Support Overview / How To

How To

1096 results

Sort

Page size

How do I power on and pair the Everest 750NC headphones?

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

Was this helpful? Thank you for your feedback!
How do I power on and pair the Everest 310/710 headphones?

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

Was this helpful? Thank you for your feedback!
How do I power on and pair the Everest 110 headphones?

Press and hold the center button located on the inline microphone. It helps to have one or both ear inserts in the ear to hear the audio voice prompts. Once you press and hold the power button, you will hear the audio voice stating, "powering on". If this is your first time pairing the device, it will automatically go into pairing mode and will be looking for the device. Make sure the device you are trying to connect to is in search mode. It should recognize the Everest 110 within 2-3 seconds. If you would like to connect to a different device. Make sure the unit is off and proceed to press and hold the center button on the inline mic from 4-6 seconds until you hear "powering on......JBL Everest is ready to pair. Go to the pairing menu on your device" You will now be able to pair to a different device. The device should recognize the Everest 110 within 2-3 seconds and will connect.

Was this helpful? Thank you for your feedback!
How Do I Power On and Pair the E65BTNC?

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure the E65BTNC headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

Was this helpful? Thank you for your feedback!
How do I power on and pair the E45BT/E55BT headphones?

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

Was this helpful? Thank you for your feedback!
How do I power on and off UA Sport wireless headphones?

Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.

Was this helpful? Thank you for your feedback!
How do I power on and off the headphones?

Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.

Was this helpful? Thank you for your feedback!
How do I pair to a different device when using the UA Sport Wireless Flex?

In order to pair to a different device, make sure the headphones are turned off. Proceed to press and hold the power button located on the LEFT arm of the neckband. You will hear the audio voice prompt state, “powering on” Continue to press and hold the power button for 3-5 seconds or until you hear the voice prompt state, “looking for device.” Make sure that the device you are attempting to connect to is in the Bluetooth search mode and within range. UA | JBL Flex should appear on your device within 3-8 seconds. Once you choose this option on your discoverable devices, it will connect and the voice prompt will state “Connected”

Was this helpful? Thank you for your feedback!
How do I pair to a different device on the Endurance Series headphones?

To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.

Was this helpful? Thank you for your feedback!
How do I pair the subwoofer to my JBL BAR soundbar if pairing does not happen automatically?

Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show "DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.

Was this helpful? Thank you for your feedback!
How do I pair the Flip 3 SE with a different device?

Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.

Was this helpful? Thank you for your feedback!
How do I pair my subwoofer?

The SB450 soundbar is paired to the subwoofer right out of the box. If the 2 parts are not already paired together, simply press the Pairing buttons on the rear panel of both products and they will connect with each other.

Was this helpful? Thank you for your feedback!
How do I pair my phone with this amplifier?

Simply hold Bluetooth button on the remote and once its start flashing, on your device go to your Bluetooth settings and look for the gtr amp and pair it.

Was this helpful? Thank you for your feedback!
How do I pair my device via Microsoft Swift Pairing?

Swift Pair is the newest way to pair your Bluetooth peripherals Windows 10, version 1803 or above.

Steps:
1.     Put the Bluetooth peripheral in pairing mode
2.     When the peripheral is nearby, your Windows device will show a notification
3.     Selecting “Connect” starts pairing the peripheral
4.     When the peripheral is no longer in pairing mode or is no longer nearby, your Windows device will remove the notification from the Action Center

Was this helpful? Thank you for your feedback!
How do I pair an additional Bluetooth device to SB 250?

Short-press the Bluetooth Button to open for new pairing.

Was this helpful? Thank you for your feedback!
How do I pair an additional Bluetooth device to Boost TV

Short-press the Bluetooth Button to activate pairing mode. Now set your device to scan for Bluetooth devices. It will find the BOOST TV and allow you to pair to it.

Was this helpful? Thank you for your feedback!
How do I mute the microphone?

During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.

Was this helpful? Thank you for your feedback!
How do I make sure to get the best heart rate reading and accuracy?

To ensure the best accuracy, it is important that you are using the proper size and the headphones securely fit in the ear. Please reference FAQ: How do I find the proper fit? to make sure you are wearing them correctly. You should also make sure that the enhancers are properly installed on the ear buds so that material is fully stretched over the bud and the window for the heart rate (HR) sensor is not covered. Please reference FAQ: How do I switch enhancer sizes? for more guidance. Once you've found your ideal size and ensure they're installed correctly, make sure the HR sensor is on. When it is on, you will see a green light on the LEFT ear bud and should hear the audio prompt stating, “Heart Rate sensor on”. For best results, insert the earphone into your ear so that the green heart rate sensor on the LEFT ear bud is fully hidden inside the ear (behind your tragus). Double check that the ear bud is touching the back of the bowl of your ear for the most accurate signal - this is often times achieved by using the largest size that fits comfortably in your ear. Lastly, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone loop and your ear. You should hear the audible alert telling you if the ear bud needs to be adjusted if it is unable to retrieve a proper reading on your heart rate. Heart Rate accuracy can vary depending on the type of exercise you are performing; it is recommended for steady state endurance-oriented activities to ensure best accuracy. While the technology is state-of-the-art, there are limitations that may cause some readings to be inaccurate under certain circumstances. These circumstances include physical characteristics, fit, and the type of activity as outlined above. The heart rate monitor data is not intended to be used for medical purposes, nor is it intended to diagnose, treat, cure or prevent any disease or condition.

Was this helpful? Thank you for your feedback!
How do I lock my JBL Endurance DIVE before going into the water?

Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.

Was this helpful? Thank you for your feedback!
How do I know which voice assistant does what?

After you set up Alexa and Google Assistant via the JBL One app, you will see examples of what you can do with each assistant. For more information on what each voice assistant does, visit Alexa Features or Explore Google Assistant .

Was this helpful? Thank you for your feedback!
How do I know when the headphone is fully charged?

When the headphones are charging, you will see a solid red light at the top of the inline microphone. When the headphones are fully charged, the red light will shut off. You should expect 8 hours of playback time. Please keep in mind that the level of volume can effect the longevity of the battery life.

Was this helpful? Thank you for your feedback!
How do I know when the battery in the Flip 3 SE needs charging?

The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.

Was this helpful? Thank you for your feedback!
How do I know the battery level of my Under Armour Sport Wireless Heart Rate headphones?

Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.

Was this helpful? Thank you for your feedback!
How do I know that I have the best fit with the 500 Series headphones?

By habit, we try to shove earbuds into our ear canals in attempts to get them to stay in. The 500 Series headphone is a completely different concept. The tip of the enhancer (ear tip) should funnel gently down into the ear canal and the base of the enhancer should fill the entire concha (bowl) of your ear. If there is still quite a bit of space between the back of the enhancer, and the back of the bowl of the ear, there is nothing to support it and it will eventually fall out. Typically larger sizes will fill the extra space inside the concha. We recommend trying both sizes featured in the packaging. If you are still experiencing fit issues, please reach out to your local JBL Customer Support for information regarding different sizing options.

Was this helpful? Thank you for your feedback!
How do I know if the Heart Rate sensor is in the correct position?

You will hear an audio prompt to readjust the position of the left ear piece stating “heart rate not detected, adjust ear bud position”. The sensor is also in the correct position when the green LED light is not visible from the outside of your ear.

Was this helpful? Thank you for your feedback!
How do I know if the headphones are fully charged on the UA Train headphones?

As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.

Was this helpful? Thank you for your feedback!
How do I keep the radio playing after having been awakened by radio?

After the wake-up process is finished, and the radio alarm has been turned off by pressing the alarm button, it is necessary to press the radio button to keep the radio playing.

Was this helpful? Thank you for your feedback!
How do I get the best audio performance of the JBL Authentic 300?

For the best performance, connect the speaker to a power outlet.

Was this helpful? Thank you for your feedback!
How do I get Hi-Res audio on my JBL Tour One M3?

The built-in Digital-to-Analog Converter (DAC) makes it possible to enjoy lossless high sound quality with low distortion and accurate conversion.
Connect the headphones with the included USB-C cable or 3.5mm aux cable to any audio source to enable Hi-Res audio. If you want to have Hi-Res audio wirelessly you need to connect an Android device with at least Android OS 13 or higher and use streaming sources such as Apple Music, Tidal or Amazon Music.

Was this helpful? Thank you for your feedback!
How do I get a secure fit with the UA Sport Wireless?

First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional earbuds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. These headphones come with 5 sizes of fit enhancers (4, 5, 6, 7 & 8) and 3 sizes of ear tips (small, medium & large). The fit enhancers sit in the bowl of your ear and are essential for a secure fit, while the ear tips are inserted in the inside of the ear canal and provide sound occlusion. The size 7 fit enhancer and large ear tip comes pre-installed on the headphone. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size.

Was this helpful? Thank you for your feedback!
How do I get a secure fit with the Headphones?

First, it is very important that you use the correct size enhancers (rubber tips). While the tips may appear too large, these do not go all the way into your ear canal. The enhancers are supposed to fill the entire bowl (concha) of your ear, so please be sure to try both sizes to ensure a comfortable fit. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. Next, gently insert the enhancer into your ear with a forward motion towards the jaw, twist and lock into place. If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email us from our Support Page at https://www.jbl.com/support-contact.html to request yours today.

Was this helpful? Thank you for your feedback!
How do I get a copy of my invoice?
You can download a copy of your invoice on our website. Go to "Order Status" under "Order Support" in the menu bar. To access your order details and download your invoice, you will need the following details:
- Order number
- Surname
- Billing postal code
Once directed to your order details, there is an option to download your invoice.

The details on your invoice is a direct reflection of your order details. We are unable to amend the details on your invoice.
Was this helpful? Thank you for your feedback!
How do I fix AirPlay not streaming music to my speaker/soundbar?

If you cannot stream music with AirPlay, use the JBL One App;
(1) Go to Settings.
(2) Select 3rd Party Service.
(3) Select the Airplay tile.
(4) Select Reset AirPlay.

Was this helpful? Thank you for your feedback!
How do I find the proper fit with my Under Armour Sport Wireless Heart Rate headphones?

First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional ear buds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left ear bud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. After the enhancers are securely locked in the ear, we recommend wrapping the ear loop up and over the ear for the most comfortable fit. Please note, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone and your ear. The size 7 will be featured on the model; two smaller sizes (5 & 6) and one larger (8) will be included in the packaging. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size. If you’re unable to find a secure fit, one our fit specialists can assist you with a different size or guidance on how to properly wear these headphones. For any questions or concerns regarding fit and sizing, please contact your local JBL Customer Support or please email us from our Support page at https://www.jbl.com/support-contact.html.

Was this helpful? Thank you for your feedback!
How do I enable Sidetone on JBL Quantum Stream?

Sidetone is off by default.

To enable sidetone on your JBL Quantum Stream microphone, install and start JBL QuantumENGINE, and head to the "Microphone" tab.

Here you can select sidetone level from 0 to 3 (0 = off).

Was this helpful? Thank you for your feedback!
How do I disconnect 2 speakers using JBL Connect?

Simply turn off one of the products.

Was this helpful? Thank you for your feedback!
How do I disable Sidetone on JBL Quantum Stream Studio?

Sidetone is by default enabled for the JBL Quantum Stream Studio. You can lower the sidetone volume or mute it by pressing the multifunction knob until you are at the audio/voice balance function. Turn the knob towards the voice (microphone icon) to increase the audio volume and lower down the sidetone volume at the same time. Turn the knob towards the headphone icon to increase the sidetone volume and reduce the audio volume.

Was this helpful? Thank you for your feedback!
How do I connect to a different device?

Press and hold the power button located on the neck band for 3-5 seconds or until you hear the audible voice stating, "powering on.......JBL Everest is ready to pair. Go to the pairing menu on your device" While it is in pairing mode you should see the LED light on the neckband alternate between white and red. The device that you are trying to connect to should recognize the Everest Elite 100 within a few seconds. Once connected, you should see a flashing LED white light on the neckband.

Was this helpful? Thank you for your feedback!
How do I connect to a different device?

Make sure that the headphones are turned off. Press hold the power button for 3-5 seconds until you hear the audible voice stating “looking for device” You will see the LED lights flash red and blue as it is searching for a new device to connect to. Make sure the device you are trying to connect to is in search mode and it should recognize the device within a few seconds.

Was this helpful? Thank you for your feedback!
How do I connect the JBL Stadium GTO 20M midrange dome in my car system?

The Stadium GTO 20M is intended for use with the Stadium GTO two-way systems, or to replace existing midrange speakers in systems that are already three-way from the start. The Stadium GTO two-way component systems are 3-way upgradeable. The crossovers are gap-switchable to accommodate a midrange upgrade. The optional Stadium GTO 20M midrange includes a bandpass crossover to convert a two-way system into a threeway system with perfect tonal balance. You simply connect both crossovers to the speaker wires from your car amplifier in parallel, and set the existing GTO two-way crossover to GAP function. Stadium GTO 20M is designed to also fit into many factory three-way applications. Please note that you cannot use this add-on midrange with coaxial car speakers, unless you can access the crossover networks to establish the midrange gap that the extra midrange is meant to occupy.

Was this helpful? Thank you for your feedback!
How do I connect the inputs and outputs of the Club 5501 car amplifier?

The Club 5501 is a mono amplifier for subwoofer use in cars. It can be confusing to see that it has two inputs, marked left and right, as well as two speaker output pairs. But it is still a mono amplifier, with only one channel. The two inputs are there to make it easier to connect to a normal car radio/head unit, where you will often have two normal full-range connectors, left and right. You can insert both into the 5501. However, if you only have one signal lead going to the 5501, you can use either of the inputs. They are combined into one inside the amplifier anyway. Also, the two sets of speaker connections are there to make it easier to connect two subwoofers simultaneously. The two sets are completely identical, so you can use either one for a single subwoofer, or both. If you connect two, they will be in parallel.

Was this helpful? Thank you for your feedback!
How do I connect my UA BT headphones to a different device?

To pair a different Bluetooth device, make sure that the unit is turned off. You then must press and hold the center button for about 3-5 seconds. You should see the light blink red and blue while it is in pairing mode and the audible voice should state, “looking for device”. You should see UA BT Wireless pop up on the device that you are attempting to pair it with. Choose that option and wait for the audible voice to state, “connected”

Was this helpful? Thank you for your feedback!
How do I connect my TV to my boost TV?

First connect your audio/video sources to your TV inputs. Then connect the provided optical or analog audio output from your TV to the Boost TV.

Was this helpful? Thank you for your feedback!
How Do I connect my T450BT via Bluetooth?

In normal use, T450BT pairing mode is automatic. First time it is switched on, it goes into pairing mode at once, shown by the blue LED blinking. After first pairing, if the last used source is not on when the T450BT is switched on, it will wait about 10 seconds with the LED showing white light, then it will switch to pairing mode, with the LED turning blue, and blinking. If you want to start pairing mode manually, make sure that the headphones are switched off, then press and hold the on/off button for more than 5 seconds. The headphones will now switch on in pairing mode, shown by the blue LED blinking.

Was this helpful? Thank you for your feedback!
How do I connect my JBL LIVE headphones to my device via Bluetooth?

To pair the JBL LIVE headphones the first time, switch the headphone on, look for the blinking blue light indicating pairing mode. Switch on Bluetooth on your source device, find the JBL LIVE headphones in Settings > Bluetooth and confirm pairing. To pair the JBL LIVE headphones from the second time onwards, or to link them with a different device, press and hold the power button until the blue flashing light is visible.

Was this helpful? Thank you for your feedback!
How do I connect my headphone to Amazon Alexa on my device (iOS and Android)?

- Visit App store and download ‘Amazon Alexa’ App.

Was this helpful? Thank you for your feedback!
How do I connect my headphones to UA Record?

To set up and enjoy all the features of your UA Sport Wireless Heart Rate, you’ll need to connect it to your phone using the UA Record™ mobile app. Select the UA Sync icon in the upper right hand corner of the dashboard. Tap on “UA Sport Wireless Heart Rate”. Follow the on-screen instructions to finish setup. Once connected, the headphones will live under My Apps and Devices. Here, you can access your headphones' settings to check your battery level, current heart rate, and help.

Was this helpful? Thank you for your feedback!
How do I connect JBL DRG to my smartphone and head unit both via Bluetooth?

• Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.

Was this helpful? Thank you for your feedback!
How do I connect JBL DRG to my head unit via FM?

• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.

Was this helpful? Thank you for your feedback!
How do I clean my yurbuds?

To clean yurbuds, remove the enhancers (tips) from earphones and wash with warm, soapy water. Do not use anything containing alcohol. Completely dry the enhancers and reposition on the earphones, as shown in the Quick Start guide: Left bud between 3:00 and 4:00 position Right bud between 8:00 and 9:00 position

Was this helpful? Thank you for your feedback!
How do I clean my product?

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.

Was this helpful? Thank you for your feedback!
How do I clean my JBL Quantum 910 Wireless headset?

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.

Was this helpful? Thank you for your feedback!
How do I clean my Earphones?

We recommend cleaning the earphones with audio or electronic wipes.

Was this helpful? Thank you for your feedback!
How do I check my heart rate on the JBL Reflect Fit headphones?

Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.

Was this helpful? Thank you for your feedback!
How do I charge the Under Armour Sport Wireless Heart Rate headphones?

The UA Sport Wireless Heart Rate must be charged with a micro USB charger that is provided in the packaging. You will find the USB outlet located on the bottom left side of the inline microphone. There will be a small rubberized window that you can slide up and over to expose the outlet. After plugging in the headphones, you will see a solid red light appear at the bottom of the inline microphone. Once the headphones are fully charged, the red light will turn off. It typically takes less than 2 hours of charging time to receive the 5 full hours of audio playback.

Was this helpful? Thank you for your feedback!
How do I charge the T110BT headphones?

The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.

Was this helpful? Thank you for your feedback!
How do I answer calls on the JBL Soundgear?

To answer and hang up calls, press the pause/play button located on the left arm of the Soundgear.

Was this helpful? Thank you for your feedback!
How do I adjust the volume on the UA Heart Rate Wireless?

To increase the volume, quickly press the top button located on the inline microphone with several quick clicks. If you want to decrease the volume, quickly press the bottom button with several quick clicks until desired volume is achieved.

Was this helpful? Thank you for your feedback!
How do I activate voice command?

Tap and hold the right earpiece for 4 seconds.

Was this helpful? Thank you for your feedback!
How do I activate the SIRI® and Google Now™ voice assistant integration on my JBL Boombox?

1) Download and run the latest JBL Connect app on your phone 2) The JBL Connect app will begin discovering your JBL Boombox (please make sure your speaker is connected via Bluetooth first) 3) Use the toggle switch in the JBL Connect App to change the phone button to now have the voice assistant function 4) Simply press the “Play” button on your JBL Boombox (you will hear a brief tone) and begin speaking your commands via SIRI and Google Now. 5) Please check the below links for more information regarding SIRI and Google Now available voice commands: SIRI: https://support.apple.com/HT204389 Google Now: https://support.google.com/websearch/answer/2940021

Was this helpful? Thank you for your feedback!