JBL Vibe 300TWS
Aidosti langattomat nappikuulokkeet
Sold from 2022 until now
Getting started with your JBL Vibe 300TWS
Documents & Downloads
Product Specifications
- Elementin koko (mm)
- 12
- Elementin herkkyys @ 1kHz/1mW (dB)
- 105
- Dynaaminen taajuusvaste (Hz)
- 20 Hz – 20 kHz
- Impedanssi (ohmia)
- 32
- Elementtien määrä per korva
- 1
- Paino (g)
- 7.7
- Paino (oz)
- .27
- Bluetooth profiilit
- A2DP V1.3 AVRCP V1.6 HFP V1.7
- Bluetooth-taajuus
- 2.4 GHz - 2.4835 GHz
- Bluetooth-lähettimen modulaatio
- GFSK, π/4–DQPSK, 8–DPSK
- Bluetooth-lähettimen teho
- <12 dBm
- Bluetooth-versio
- 5.2
- Charging case battery life (max hours)
- 20
- Latausaika (tuntia, kun akku on tyhjä)
- 2
- Maksimi toistoaika (tuntia)
- 6
- Bluetooth
- Kyllä
- Charging cable
- Kyllä
- Puheääniavustaja
- Kyllä
- Sisäänrakennettu mikrofoni
- Kyllä
- Latauskotelo
- Kyllä
- Hands-free-puhelut
- Kyllä
- Ladattava akku
- Kyllä
- Pikalataus (5 min = 1 tunnin soittoaika)
- Kyllä
- Hikeä hylkivä
- Kyllä
- Kosketusohjaimet
- Kyllä
- Aidosti langaton
- Kyllä
- Langattomat
- Kyllä
- IPX-luokitus
- IPX2
Aidosti langattomat nappikuulokkeet
Pysy ajan tasalla maailmastasi. JBL Vibe 300TWS -nappikuulokkeet tuovat musiikkisi esiin ja pitävät samalla yhteyttä ympäristöösi ilman johtoja. Nauti 26 tunnin tehokkaasta äänentoistosta, johon on lisätty JBL Deep Bass. Pysy yhteydessä matkalla stereopuheluiden avulla ilman häiritsevää taustamelua. Kätevien kosketuspainikkeiden ansiosta voit hallita ääntä ja puheluita ilman käsiä jommasta kummasta kuulokenapista tai molemmista. Ergonomisesti suunnitellut kuulokkeet istuvat korviin tiiviisti ja huomaamattomasti. Olosi pysyy mukavana ja ne pitävät sinut yhteydessä koko päivän, joten et jää koskaan paitsi tahdista – tai keskustelusta.
FAQs & How-Tos
-
As with all in-ear headphones, our range of True Wireless Stereo headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.
If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). This should remove the wax and resolve the volume/balance issues.
Was this helpful? Thank you for your feedback! -
Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off).
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.Was this helpful? Thank you for your feedback! -
If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.
https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Call us
Call us now at:
+358 972 522 301
Monday - Friday: 10:00 - 18:00
Chat with us
Monday - Friday: 10:00 - 19:00
Saturday - Sunday: 11:00 - 17:00