How To

How To

1090 results
  • As with all in-ear headphones, our range of True Wireless Stereo headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

    If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). This should remove the wax and resolve the volume/balance issues.

  • The top panel LEDs are flashing because the OTA firmware update is in progress, the product should work after the upgrade is completed. It may have been caused by a previous interruption to an update.


    It should be possible to resolve the issue by doing the following:

    • Plug in the power cable and wait for at least 5 minutes for the Partybox Ultimate to complete the update.
    • If the Partybox Ultimate stops flashing, but cannot power on, then perform a factory reset by pressing the two buttons below for more than 10 seconds: Moment (heart symbol) and Play (or through the JBL One app). After this has been done, press the Power button. 
  • Yes, it's 14 hrs with RGB off. You can also find the details on the box.
  • To configure the 7.1 Surround feature on your PC, please follow the guide below:

    1. In the left corner on your screen right next to the Windows logo, click on the spy-glass to start a search on your PC.
    2. Type in Sound --> then select Change System Sounds:

    3. Make sure that your the Quantum Headphones is your Default Device for both Speakers ( Game ) and Earphone ( Communication device )

    4. To configure the 7.1 Surround feature, right click on the Speakers --> then select Configure Speakers

    5. Select 7.1 Surround and click on Next
    6. Make sure that all boxes are selected, then click Next
    7. Make sure both boxes are selected, and then click Next
    8. Click on Finish. Now your Quantum headphones is configured for 7.1 Surround sound. The configuration will remain after rebooting PC or reconnecting headphones.
    Enjoy your sound experience #SoundIsSurvival #DareToListen
  • If you have already setup your JBL BAR 5.1 SURROUND with Google Home or AirPlay, you can now sign into your Amazon account via the JBL BAR Setup App.  Just download the app and follow the instructions.
  • No. Alexa notifications must be set up in the Alexa app and you can control the notification via Alexa voice only.

  • Yes, you can use the universal command “ Stop”, “Dismiss”, “Cancel” and “Quiet” to stop the current music playback, alarm and timer.

  • No, unless you have set up devices with both voice assistants, you cannot use Alexa to control devices you set up only in the Google Home app, or use Google Assistant to control devices you set up only in the Alexa app.

  • The Bluetooth connection will not keep playing once you have switched the source. Simply press play again on your Bluetooth device to start streaming once again.
  • This is because most Windows do not support A2DP stereo audio streaming via Bluetooth, the standard for music-listening through Bluetooth. The system will support keyboards, mice, printers etc. via Bluetooth, but not audio. It is necessary to download the proper drivers, either from the computer manufacturer, the software manufacturer or the manufacturer of the Bluetooth chip in the computer. Help to do this must be sought with the companies that supply one or more of these computer features.
  • On backup battery power, please wait 50 seconds for the alarm to turn off automatically.

  • You must first set a radio preset by tuning to a radio station and holding down the 1, 2, or 3 button to save it. After this, the preset will be an option when setting up a new alarm.

    When setting up the alarm, the options will be displayed in the following order:

    ​​​​​​1. Set Alarm Hour.
    2. Set Alarm Minute.
    3. Set Recurrence - Weekday/Once.
    4. Set Ringtone - 4 built-in alarm tones or radio preset 1/2/3 (see information above).
    5. Set Light - On/Off.

    If the light is set to 'On' when the alarm is set up, once it goes off it will gradually increase in brightness over 10 seconds.

  • You can easily adjust the volume to your choosing while setting your alarm on the Horizon 2. When setting your alarm, choose the Alarm Bell 1 or the Alarm Bell 2 on the top of the speaker. As you go through your settings when choosing an alarm time, it will give you the option to adjust the volume setting you wish to have on the alarm. Just simply adjust the volume by turning the volume knob on the top of the speaker. After you choose the volume, press the volume knob once to move to the next settings option. 
    Please note: the alarm volume will gradually increase until you choose to either snooze or turn the alarm off completely. 
  • Yes, you may charge your speaker from your desktop or laptop, but the charging time will be longer than using the supplied power adapter.
  • This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.
  • The JBL Bar series soundbars supports three CEC commands: - System Standby - One Touch Play - Audio Return Channel.
  • No, shipping is on us. You can send your order back within 30 days for a full refund.


    To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.

  • No. Although the Control X Wireless have a rugged exterior and are portable, they are not all-weather speakers. Any direct exposure to harsh weather condition (rain, snow, extreme hot/cold temperatures) will damage the speakers.
  • The product is Water Resistant and Sweat Resistant, but you cannot swim with these headphones.
  • No. The Everest 110 are not sweat proof and do not have an IPX rating that protects the headphones from sweat and water. Over exposure to sweat and water can cause significant damage to the headphones.
  • No. The Everest 150NC do not feature an IPX rating and are not designed to be overexposed to moisture. Overexposure can compromise the controls and sound.
  • The ear pads on the three second-generation Everest headphones are fixed to a plastic plate, held in place on the ear pods with small claws. It is not very easy to remove it, and sometimes one or more of the claws may break off. This means that it is usually best to have a service technician do the replacement, but if you have new pads at hand, and is handy with tools, you may do it yourself.
  • Yes, you can control the amount of outside noise to let in with our Ambient Aware options offered exclusively through the JBL app.
  • No. The ear pads are made from a synthetic protein leather.
  • Yes, both of them are rated IPX7, which means they can be submerged in clear water for up to 30 minutes at up to 1 meter of depth. Make sure the charging cover is closed, or water will get into the product and damage it.
  • While the Partybox Encore does not have a Microphone Input, it does have an internal receiver for the wireless microphone that comes with the product.


    It is possible to pair one of the microphones from the Partybox Wireless Mic * (sold separately from the Partybox Encore, containing 2 x Wireless Microphones and 1 x Receiver/Dongle for connection with 6.3 mm microphone jack inputs) - however, a maximum of 2 wireless microphones can be connected to the receiver at a time.


    As an alternative, a spare part accessory is available (dependent on stock levels), which includes just 1 x Microphone for Partybox Encore - search for the aforementioned product name or "FG7261JMJ100114" in our online store.


    To connect an additional Wireless Microphone to the Partybox Encore, follow these steps:

    Switch off the Partybox & both microphones.

    Once off, switch on both microphones only, then switch on the Partybox and both microphones should connect to the receiver.

    If not, please try the same instructions as above expect with a Factory Reset (Press and hold the "Play" and "Light" buttons for > 10 seconds) instead of the restart above, then follow the microphone pairing procedure:

    1. Turn off the speaker.

    2. Make sure that the distance between the new wireless microphone and speaker is within 1 meter. Turn on the microphone.

    3. Turn on the speaker. The microphone will pair and connect with the speaker automatically within 3 minutes.


    *Please note that regarding the older version of the JBL Partybox Wireless Mic - the JBL Wireless Microphone Set - the microphones are not compatible with the Partybox Encore whatsoever, as they use UHF instead of 2.4 GHz for communication between the microphones and receiver (and the Partybox Encore does not have a Microphone Input).

  • Yes. Our Everest series headphones are made with synthetic protein leather which is a non-animal leather.
  • Yes. Our E series headphones are made with synthetic protein leather.
  • Yes. Our E series/Duet headphones are made with synthetic protein leather.
  • No. Our Everest series headphones are made with synthetic protein non-animal leather.
< 1 2 3 4 5 6 ... 37 >

Can’t find what you’re looking for?

Call us

Call us

Call us now at: +45 32712498

Monday - Friday: 09:00 - 17:00

E-mail us

E-mail us

We are here Monday – Sunday to answer you as fast as we can!

Email us
Chat with us

Chat with us

Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00


WhatsApp Us

Send us a message here 

Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00