Try below steps. Attach the charger so the device is charging. While charging: First try to hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds (this resets the Flip 3 to factory settings). If this does not help, press and hold the "Volume +" and "Link" buttons for more then 10 seconds (this will exit demo mode). As a last step, short press on the "Volume -" & "Volume +" & "Phone" buttons. If the device will still not turn on, it has a defect.

1. Insert both earbuds into the charging case.
2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
 

Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.

If you are experience connectivity problems with Wi-Fi connection, please try to reset all Wi-Fi settings. This can be done by pressing power button for 10 seconds, the power button will quickly flash to indicate it has been reset. After you have reset all Wi-Fi settings, please shutdown the device and pull out the power cable from the wall socket. Put back in the power cable into the wall socket and try do the Wi-Fi setup again.

This product features Multi-Point Connection which allows you to be connect to two devices at the same time. Effortlessly switch from listening to music on your portable device to a call from your phone.

To connect to two devices at the same time:

1. Power on your product.
2. Make sure that the device you wish to connect to has the BT settings on and within range.
3. If this is the first time connecting your product, you will notice a flashing LED to indicate that it is searching for a device to connect to. (If this is not your first time, your product will automatically reconnect to the last device it was connected to)
4. Under your BT settings, go to discoverable devices and the product name should pop up within a few seconds. Depending on the device you are using, you may have to tap on the product to complete the connection. 
5.Now that you are connected to the first device, push the BT button on the product to connect to the second device. The product should start searching for the second device by displaying a flashing LED.
6. Go to your BT settings on your second device. The product should pop up on your discoverable devices should pop up within a few moments.

(Please Note: If the product does not show up on your discoverable devices while it is in pairing mode, quickly turn off your BT settings and turn it back on. This will typically result in resetting the BT search in which your product should pop up on discoverable devices within a few moments)


 

To connect and play music from a second source device using multi-point connection, simply press the Bluetooth button and connect to the product in the settings of the source device.

When using multi-point connection and switching between iOS, Android and Windows, there may be no music output or a delay in music playback. To resolve this issue, it is always recommended to pause or stop music playback on one Computer/PC/Laptop before multi-point switching to another device (Phones, Tablets) for music playback.

If the issue persists, we recommend to restart both the product and the Computer/PC/Laptop.

While using the Wired Aux Connection, the microphone will be switched off. 

Make sure both the QuantumENGINE software and the headset's firmware is updated to the most recent version, and that the microphone is plugged all the way in.

Below you can see the placements of the microphones on some of our headphone models:

Live Pro+ TWS


Tour Pro+ TWS


Tour One

If the wireless mic is out of signal range, you will experience drop outs or no sound. Once range is reestablished, the speaker should automatically detect the mic and resume connection within less than 3 sec. 

When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds. 

If one of the wireless mics is not working, we recommend the following: 

1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound 
 

Yes. This headphone has a built in microphone. To answer a call, press the power button which is located on the Left Ear Cup for 1 second. If you wish to hang up the call, press and hold the power button for 2 seconds.

Microphone Cleaning (handheld mics)

There are two very important reasons to keep your microphone clean.

1. Hygiene/Germs, especially when a mic is used by multiple people, can unknowingly be spread.
2. Dried spit, dust, dirt and debris can build up in the screen and sponge, negatively affecting the microphones’ ability to accurately pick up and reproduce the voice or instrument.

To clean the microphone…

1. Remove/Unscrew the grille from the microphone, turning counter-clockwise.

2. Remove the foam from the inside of the grille.

 

3. Wash the foam with warm water and dish soap.
4. Clean the grille with any household non-abrasive disinfectant/cleaner.
5. Thoroughly dry both the grille and the foam.
6. Insert the foam into the grill.
7. Screw the grille back onto the microphone, turning clockwise.

 

NOTE: For quality purposes, it is recommended that the screen of the microphone be cleaned once per month when used on a regular basis. For hygienic purposes, when used by multiple people, cleaning is recommended more often, possibly even nightly.

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.

Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”.

The Left and Right bud should sync together automatically when removed from the case. If the Left and Right bud do not sync together automatically within 15 seconds, you may manually sync the buds together. With the buds out of the case, press the center button on each bud 3x. This action does not have to be done simultaneously. You may start with either the L or R bud to initiate syncing.

LIVE FREE 2 TWS
Software Update Release Notes
------------------------------------------------------------------------
Software Version:  V6.9.8
Version (iOS):  V5.7.9
Version (Android):  V5.7.9
Release Date:  July 8, 2022
Release Media:  OTA via JBL Headphone App


What’s New

1. Added Microsoft Swift Pairing feature.
2. Fixed a few minor software bugs for better user experience.

If the left ear pod is silent, please perform a new pairing with the right pod like shown in the quick-start guide.
Take them out of the charging case and click the  center button on both the left and the right pod 3 times.
This forces a new pairing between the pods, and the left pod should automatically pair with the right pod from now on once you remove both pods from the charging case.

If you still cannot get the Left ear to play, please perform a factory reset by placing both pods in the charging case, while the charging case is charging. Now press the button on the right pod, and hold it for more than 5 seconds. You have now reset to factory settings. (Please note: If you have performed a factory reset, you will need to remove the headphones or "forget this device" from any smart phone or tablet they were once connected to. This will allow your device to now search for the newly restored headphones under BT devices)


The right pod is the primary, which is connected to your source, usually a smartphone.
The left pod is the secondary, which connects to the right pod.
 

The Checklist

Let us walk-through a list of things needed to ensure every requirement is met.

1. Check your mobile device if that is able to connect to same Wireless network.
2. Make sure you are within range of your Wireless router.
3. Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
4. Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
   1. You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
   2. You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
5. Try using a different mobile device, if you have one.
6. Reboot your Wireless network router and your mobile device.

Watch the video below for help with setting up your Google Assistant device.

Wireless Network Extender

Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.

1. Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
2. Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
3. Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
4. To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
5. In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).

One Wireless Network Name (SSID)

1. You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
2. If the speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
3. To solve this issue, using two different name for your extended network will help with the performance of the Speaker and Google Assistant request.

 

The JBL Xtreme will not be supported by the JBL Portable app while using Apple devices with iOS 14 or later versions due to incompatibility. 
You can continue to use the speaker through Bluetooth or Aux connection and manual pairing, but cannot stereo pair with another Xtreme through the JBL Portable App.  
There is no plan to release a new Firmware currently as the JBL Xtreme has been discontinued.

If you still wish to use JBL Xtreme with the JBL Portable app, please connect it with Apple devices with iOS 13 or below, or connect it with Android devices.

The JBL Trip visor mount is bi-directional. Mount the clip to the other side of visor as shown in the “quick start guide” section 8. This will help displace the weight differently and your issue should be solved.

JBL Quantum Headphones Upgrade tool redefines your headphones experience. Through your macOS device, you can now conveniently upgrade the headset.
Download from macOS app store: https://apps.apple.com/us/app/jbl-quantumengine/id1645040444

Supported models are:

- JBL Quantum 610

- JBL Quantum 810

- JBL Quantum 910

- JBL Quantum 910P

- JBL Quantum 910X

- JBL Quantum TWS

You can adjust Equalizer, Spatial Sound, RGB LED effects, change microphone settings and update the headset's firmware

The single ANC/TalkThru button accomplishes several tasks, turning the ANC on and off, and turning the TalkThru on and off.  It behaves slightly different than you might expect.  Here is a description of how to accomplish each task.

To turn ANC on and off
Short Press: ANC On (voice prompt states ANC On)
Short Press: ANC Off (voice prompt states ANC Off)

To turn TalkThru on and off
Long Press: TalkThru On (voice prompt states TalkThru On)
Short or Long Press: TalkThru Off, but ANC is now On (voice prompt states ANC On)
Short Press Again to turn ANC Off as well (voice prompt states ANC Off)

NOTE:  The voice prompt will never state that TalkThru is Off.
 

JBL PORTABLE App
Software Update Release Notes
------------------------------------------------------------------------
Version (iOS):  5.6.7
Version (Android):  N/A
Release Date:  September 13, 2022
Release Media:  App Store (iOS)


What’s New

1. Solved the issue that iOS 16 users could not use JBL PORTABLE App

You cannot download the JBL Portable App on a PC. This app is only available on mobile devices.

Rated Power Output

Partybox 110:
AC Power 160W
DC Power (battery) 100W

Partybox 200:
AC Power 120W
12V (car) 90W (PLEASE NOTE: NO BATTERY)

Partybox 300:
AC Power 120W
DC Power (battery) 90W
12V Power (car) 90W (PLEASE NOTE: DOES NOT CHARGE THE PARTYBOX, ONLY POWERS)

Partybox 310:
AC Power - 240W
DC Power (battery) - 140W
12V Power (car) - 140W (PLEASE NOTE: DOES CHARGE THE PARTYBOX)

Personi-Fi 2.0 is a new feature available through the JBL Headphones App. This feature helps to personalize the sound using the best possible sound curve based on your hearing capabilities. It will first ask a few questions, and then check your current ambient audio. You will be informed that this step should be completed in a quiet environment. It will play a series of test tones in all the different frequencies wherein after each frequency test tone is played, it will ask you what is the lowest volume setting you can hear. Nine different sounds will be played in each ear (18 in total).

Simply press and release the button when you hear a sound. After it goes through all the test tones, it then calculates the best sound for your ears based on the results. It allows you to demo the results by playing a track. You will be able to toggle it on/off to hear the difference.

PSAP (Personal Sound Amplification) is a new feature accessible within the JBL Headphones App. When this feature is turned on, it works similar to Ambient Aware, but it focuses on picking up vocal frequencies in front of you. 

 

1. GAIN: The Personal Sound Amplification function is designed to amplify sound in the vocal range, it can assist users with (limited) hearing loss to maintain conversations more easily, especially in noisy environments. It should then amplify the speech of the person sitting across from you, not the general ambient sound as with Ambient Aware. The algorithm uses beamforming to pick out the voice from the other sounds, much like what happens during a phone call, but instead of focusing on your own voice it focuses on the voice further away from you. The gain setting allows you to amplify those vocal frequencies.

 

2. BALANCE: The balance setting adjusts the amplification effect between your left and right ears using the slider. When set to 0 (in the middle), both ears will receive the same amplification, but depending on the user’s personal needs/preferences, they can focus the amplification more towards either the left or right ear. 

 

The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.

The JBL Free has an IPX5 rating that helps protect the headphones from sweat and moisture.