How To

Support Overview / How To

How To

1102 results

Sort

Page size

How to show the current software version
To show the current firmware version on your JBL TUNER device, go through the following steps.
1. Turn on the JBL TUNER.
2. Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
3. In the display, you will see a combination of letters and numbers. This is the current software version.
4. See picture below as illustration.
The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.
Was this helpful? Thank you for your feedback!
How to stream music with your Apple device

Our new JBL Link Music and Link Portable both support Apple AirPlay 2. Pick up your Apple device, use your favorite music streaming service, and connect to the JBL speaker! Please note: before using Apple AirPlay 2, you will need to install it on your WiFi network, either using the Google Home app or Apple Home app ( your choice! ).

Was this helpful? Thank you for your feedback!
How to switch between Active Noise Cancelling and TalkThru

Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.

Was this helpful? Thank you for your feedback!
How to switch between Game and Chat balance

Yes, you can adjust the game and chat audio balance by rotating the dial-up and down. When you rotate the dial, you'll feel a notch that indicates the balance is 50% game and 50% chat. The slider on Quantum ONE is different and has no notch but instead a visual indicator.

Was this helpful? Thank you for your feedback!
How to switch between voice assistants using the My JBL Headphone app
The voice assistant you select in the initial set-up (pictured below) will be used as the default assistant on your headphones.

You can change the default assistant in the ‘My JBL Headphones’ app:
1. Open the My JBL Headphones app on your device.
2. Select the headphones you are connected too.
3. Go to Settings by clicking the symbol in the top right corner.
4. Select Voice Assistant.
5. Now you can select your preferred voice assistant.
Your headphones may restart after switching Voice Assistant.
Was this helpful? Thank you for your feedback!
How to Turn Off or Snooze the Alarm

Once an alarm is set and starts to ring, it can be snoozed by tapping the large central knob/button on the top of the unit (circled in yellow in the image below). If this button is held for more than 2 seconds it will turn off the alarm.

The duration of the snooze cannot be changed and is fixed to 9 minutes. The alarm will continue to ring for 3 minutes and if not turned off or snoozed, it will automatically snooze after this time. It will automatically snooze for a maximum of 3 times, but if the snooze button is used before this occurs, the alarm can be snoozed an unlimited number of times.

Once snoozed, the display shows the time that the alarm will next ring.

To keep the radio playing after the alarm is turned off, press one of the 3 preset buttons or the DAB/FM button as desired.

Was this helpful? Thank you for your feedback!
How to Turn off the Lightshow

Press and hold the Lightshow button for more than 2 seconds to turn off the Lightshow.

Was this helpful? Thank you for your feedback!
How to Turn off your TWS Headphones

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

Was this helpful? Thank you for your feedback!
How to turn on TV with your voice

To turn on/off the TV, the recommended control is “OK Google, turn on”/”OK Google, turn off.”

Note that this depends on your TV manufacturer and if they support this via HDMI CEC (This works only for HDMI connection).

Was this helpful? Thank you for your feedback!
How to update the headset

You can update our Quantum 600 and 800 using the QuantumENGINE software on your PC.
To update the headset, go to SYSTEM SOFTWARE tab, find section HEADSET, and press CHECK FOR UPDATE and then INSTALL UPDATE.

Was this helpful? Thank you for your feedback!
How to update your Remote control
The remote control included with your LINK BAR can be updated, if a new version becomes available for your device.

There are two ways to find out if an update is available.
- A notification on your Android TV screen will appear. When clicking on it with your remote, more information will pop up.
- Manually check for an update, in case you have dismissed the notification, or the system does not show it.
Checking for update
To manually check for an update, please follow the instructions.
1. Go to "Settings" on your Android TV (ICON)
2. Find Connected Devices
3. Click on LINK BAR Remote
4. Under the Update firmware, if there is an update available, you will see it under the name.

The latest firmware version for your remote control is 1.27 (Changes to firmware numbers will change in the future).

5. Confirm the update for your remote control. The system ill download the files, and automatically start to update your remote.
5.1 NOTE: The battery needs to have more than 20% power left. If your remote is under 20%, you need to change the batteries, as this may break the remote control device.
6. When the update is ongoing, you must keep the remote control near the LINK BAR. This is because the remote is using Bluetooth to communicate with the system, and updating the device happen through Bluetooth connection. The update may take around 10 minutes or less.
7. When update is complete, this message "Remote is up to date," is visible, and you have the latest firmware.
Was this helpful? Thank you for your feedback!
How To Use Alexa MRM (Multi-Room Music) on Wi-Fi
1. On an Android or iOS device, add the Soundbar to your home WiFi network through the JBL BAR Setup App.
2. Follow the App instructions to complete setup.
3. Sign in with your Amazon Alexa account. If you do not have, create one.
4. With the Alexa MRM multi-room music playback, you can stream music on your Android or iOS devices to multiple Amazon Alexa speakers.
Was this helpful? Thank you for your feedback!