In-Ear

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.


Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings  once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

                                                                                             
 
Use a clean cotton swab slightly moistened with alcohol to:

1. Remove earwax and dirt from the ear tips on your earbuds.
2. Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
3. Clean the grooves on the cover and at the bottom of the charging case.

After cleaning, make sure the charging case and earbuds are dry before putting the earbuds back into the charging case.

TIP: We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.

This headphone does not feature volume control. You must manually control volume from your device.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

This headphone does not feature volume control. You must manually control volume from your device.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

This headphone is supported by the My JBL Headphones App.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

To connect to a new device, begin with the headphones powered off and hold the center button on the RIGHT headphone for 5 seconds to enter pairing mode. You will hear the BT pairing audible chime as it searches for a different device. Make sure the device you are wanting to connect to is in range and BT is on. Once connected you will hear the audible Connected chime. Once Right ear is connected, press and hold the center button on LEFT ear for 3 seconds as it powers on and connects to the device followed by the same Connected audible chime.

This headphone does not feature volume control. You must manually control volume from your device.

To power on and pair the UA Flash, remove the ear tips from the charging case. If this is your first time using the headphones, they will automatically go into pairing mode. You will see the blue and red LED light flash on the RIGHT ear as it attempts to pair with your device. Make sure your device is in range and BT settings are ON. The JBL True Wireless Flash should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a slow blinking blue light below the UA logo on the RIGHT Ear. The RIGHT ear must be connected first in order to power on and connect the LEFT ear. To connect the LEFT ear, simply press and hold on the UA logo for 3-5 seconds until you hear the audible power on chime. (The left should automatically power on when you remove it from the case) Once powered on, it should connect to your device within a few seconds displaying a slow blinking blue LED light below the UA logo.

To charge the UA Flash, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly: 0= 0% Dead 2-3 = 40%-50% 4=100% Full battery life

In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.

The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.

The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.

This headphone does not feature volume control. You must manually control volume from your device.

No. The Live 200BT does not feature any IPX rating so overexposure to both sweat and water can compromise the headphones.

Yes. To take a call from the Live 200BT press the center button located on the RIGHT neckband for 1-2 seconds. To hang up, simply press the center button again.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

This headphone is supported by the My JBL Headphones App.

No. The Everest 150NC do not feature an IPX rating and are not designed to be overexposed to moisture. Overexposure can compromise the controls and sound.

With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

Because bluetooth cannot travel through water, the only Endurance model that is used for swimming is the Endurance DIVE model. The Endurance DIVE model features an MP3 player which allows you to listen to music under water without using bluetooth. Furthermore, only DIVE features a function lock, which prevents water from activating functions inadvertently. SPRINT and JUMP do not have this lock function, and will not work under water.

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

The JBL Endurance SPRINT, JUMP and DIVE can be used in salt water (i.e. sea) but we recommend to thoroughly wash the headphones in fresh water after every use in salt water, to remove the salt residue. Please note that only DIVE can actually be used in water, because it features a function lock and a built-in memory for MP3 music files. SPRINT and JUMP cannot be used in water, because the touch buttons will malfunction when submerged, and Bluetooth cannot function at all under water.

The headphones can pair to multiple devices but can only be connected to one device at a time.

Because bluetooth cannot travel through water, the only Endurance model that is used for swimming is the Endurance DIVE model. The Endurance DIVE model features an MP3 player which allows you to listen to music under water without using bluetooth. Furthermore, only DIVE features a function lock, which prevents water from activating functions inadvertently. SPRINT and JUMP do not have this lock function, and will not work under water.

The Endurance Dive supports SBC. But the main signal transfer is A2DP, v1.3.

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.

With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.

To connect to a different Bluetooth device, first switch the headphones off. Now press and hold the center button on the headphone remote control for about 3-5 seconds. You should see the light blinking red/blue to indicate pairing mode, and the voice prompt should state “looking for device”. You should see "Reflect Mini 2" appear on the source's BT list. Choose that option, and wait for the voice prompt to state “connected”

No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

The Reflect Contour BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.

No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.

Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The Reflect Contour headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.

Yes, the T110BT features a three button inline microphone which allows you to pause/play skip tracks, answer calls and control the volume.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.

The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.

The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.

What you are experiencing is normal. The JBL Free will automatically switch to mono mode on the RIGHT ear when the call starts. After the call ends stereo music mode will automatically resume.

Press and hold the power button which is located on the right arm of the neck band. Press and hold for 3-5 seconds until you hear the audible voice state "Powering ON" followed by "Looking for device." Make sure the device you are attempting to connect to is in search mode and within bluetooth range. You will see Reflect Fit Audio on the discoverable devices. Choosing this option will allow you to receive audio playback.

The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.

To skip the tracks forward, press and hold the volume up (+) button for 1-2 seconds and you will advanced to the next song. To start the current song you are listening to over, press and hold the volume down (-) button for 1-2 seconds. Please note: You can only advance to the next song be skipping forward, you cannot skip tracks backward. You can only restart the current song over by pressing the volume down (-) button.

Yes, the volume control buttons are located on the LEFT arm of the neckband.

To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.

The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.

No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.