Sport

The JBL Free has an IPX5 rating that helps protect the headphones from sweat and moisture.

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

To take a phone call, press the center button of the RIGHT ear for 1 second. To hang up a call, press and hold the center button on the RIGHT ear for 1 second. To ignore a call, press and hold center button for 3 seconds until music resumes.

To activate TalkThru Technology, press the LEFT ear for a short press for 1 Second which allows you to clearly hear others for quick conversations without removing headphons. Music volume level should lower when TalkThru is engaged. Press again for 1 second to turn off Talk Thru.

To charge the UA Flash, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly: 0= 0% Dead 2-3 = 40%-50% 4=100% Full battery life

To connect to a new device, begin with the headphones powered off and hold the center button on the RIGHT headphone for 5 seconds to enter pairing mode. You will hear the BT pairing audible chime as it searches for a different device. Make sure the device you are wanting to connect to is in range and BT is on. Once connected you will hear the audible Connected chime. Once Right ear is connected, press and hold the center button on LEFT ear for 3 seconds as it powers on and connects to the device followed by the same Connected audible chime.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.

This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

Yes. The UA React features an IPX7 rating which offers full protection from sweat and water. They can be fully submerged for up to 30 minutes.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

As the headphones are charging, you will see a red solid light indicator on the controller. Once the unit is fully charged, the red light will turn off.

AmbientAware Technology allows you to hear your surroundings without removing your UA Pivot headphones. To activate AmbientAware mode, double press the Bionic Hearing button on the controller. You will hear a tone, and your music level will lower when AmbientAware Technology is engaged. To revert back to normal volume, simply double press the Bionic Hearing button again.

Yes. The UA React features an IPX7 rating which offers full protection from sweat and water. They can be fully submerged for up to 30 minutes.

You will be able to control the volume by pressing the volume + and volume- buttons located on the controller.

TalkThru Technology allows you to clearly hear others for quick conversations without removing your UA Pivot headphones. To activate TalkThru mode, press the Bionic Hearing button on the controller once. You will hear a tone, and your music level will lower when TalkThru Technology is engaged. To revert back to normal volume, simply press the Bionic Hearing button again.

No. UA Train does not support AptX™ and AptX HD™ audio codecs.

To receive a call, press the center button located in between the volume- and volume+ button for 1 second.

As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.

To use the headphones, they cannot be charging. You should receive 16 hours of battery life. The UA Train also features the quick charge battery which allows you to receive 1 hour of battery life after charging for 5 min.

You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of music

With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

The headphones can pair to multiple devices but can only be connected to one device at a time.

Yes. You have the ability to control the volume which is located on the RIGHT arm of the neckband.

You can bend the ‘arms’ of the neck in and out to get the optimum fit for your exercise/level of activity. The flex zone is the black rubber part on the neckband.

Make sure the headphones are turned on and connected to your smart device. Press and hold the Microphone button located on the LEFT arm of the neckband. You should be able to activate Siri/Google within 3 seconds after pressing the Microphone button.

To skip the track forward, press and hold the volume up button. (+) If you want to skip backward, press and hold the volume down (-) The volume buttons are located on the RIGHT arm of the neckband.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

Yes. The Inspire 500/700 is an in-ear Sport Wireless Headphone.

To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire/Focus 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.