This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

Switching to a new Wi-Fi network

1. Make sure your mobile device is connected to the same Wireless Network as your speaker.
2. Open your Google Home app 
3. Go to Settings 
4. Tap on Wi-FI Forget Network
   1. The current configuration is now forgotten.
5. In your Google Home app, you are forced back to the "Home Screen" and need to setup the device again.
6. Tap on
7. Find Add   Set up device Set up new devices in your home
8. Follow the instructions given to add the speaker to your Wi-Fi network.

Lost connection or changed settings

1. Open the Google Home app
2. On the home screen, tap on AddSet up device Set up new devices in your home
3. Follow the instruction provided.
   1. Remember that your current room name is the same as before, as well as other settings made for the speaker. You are only switching to a new Wi-Fi.
4. In addition, you can click on Discovery in the bottom menu of the Google Home app.
5. Tap on the Setup The Card information would show your old speaker name.  However, you can continue setting up the device following the instructions.

 

 

To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.

With TalkThru Technology, music is lowered and speech is amplified so you can easily have quick chats. AmbientAware delivers a more immersive music experience while increasing ambient sounds, providing the safety of hearing your surroundings. You can control them via the buttons on the ear cup and with the My JBL Headphones app

To activate TalkThru Technology, press the LEFT ear for a short press for 1 Second which allows you to clearly hear others for quick conversations without removing headphons. Music volume level should lower when TalkThru is engaged. Press again for 1 second to turn off Talk Thru.

The amber LED lights indicate that you have muted the microphone and the Google Assistant. The JBL LINK will not react to any voice keywords unless you unmute the microphone.

Yes, the app only works when the headphone is powered ON and paired to a source device that has the app available.

If the audio is not centered to your monitor, then you can re-center your headset by doing the following: 1. Position yourself in front of your monitor. 2. Press the re-centering button on the side of your headset (button that looks like a circle) 3. The head-tracking sensor will start the automatic calibration.

To clean your LINK BAR, use a soft dry Microcloth to remove dust and dirt.
We wouldn't recommend using any alcohol as it may harm the product.

It is true that some Bluetooth products have a very loud BT acknowledgment tones. We are sorry, but the level of such tones cannot be changed, and no software solutions will appear.

Even when reducing volume to minimum on the Bluetooth source unit, it does not reduce the audio signal to zero. In this case the Micro Wireless will playback music at a very low volume.

True Adaptive NC available on Tour One enables real-time monitoring of exterior surroundings and personal attributes like movement, hair, eyeglasses, and automatic adjustments to the NC performance and EQ.

If you don’t prefer the canceling performance's automatic change, you can get a fine-tuned canceling level by choosing “Everyday Mode” in the app.

Adaptive Noise Cancelling - available on Tour Pro+ TWS - listens to ambient environmental noises using external and internal mics then creates the inverse phase back to the listener creating the noise “canceling” effect.
The headphones also allow the listener to adapt or adjust noise cancellation through features like Ambient Aware and TalkThru.

Make sure to press the association button once. If by mistake you pressed it more than once, there is a good chance that association does not take place. Wait until the association process is completed, which takes about 2 minutes, and repeat the process.

This can be caused by the charge arm reaching its thermal temperature cutoff. This is a safety feature to prevent a potential risk. For proper heat dissipation, always be sure to have the charging arm in the open position when your smart phone is attached.

These holes are the microphones for the JBL Link

If your LINK BAR has 4 orange LED lights in the front, this means you have "muted" the microphone which is located on the top of the speaker.
To unmute the LINK BAR use the "switch" and the front LEDs will stop illuminating orange. Now you can use the hot-words to interact with the Google Assistant/Google Search (varies from country).

Privacy information:
We call our button the "PrivacySwitch" for the moments when you don't want the bar to listen for the hot words.
Google has high privacy rules, and one of them is not to share end-user data with any third-party apps.
 

Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.

Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.

This is the charging indicator LED. I lights up red when the headphone is charging, and goes dark when charging is complete, or if no charging takes place.

As explained in our Owner's manual, it will adjust the sound to match the placement of your Soundbar, wall or table. When against a wall, the sound reflection will be different than when on a table. This button adjusts the tonal quality to give you the best audio results in either setup.

This is due to your HDMI cables. All cables attached to the HDMI inputs of the SB450, needs to be High speed cables. If your cables do not meet these requirement, then you will experience unstable connection from source to your TV.

Common fixes:
(1) Make sure that the soundbar is not muted.
(2) Select the correct audio input source on the remote control.
(3) Check the connections to your TV or other devices
(4) Perform a reset if none of the above is working. 
(4.1) Press and hold VOL -, VOL +, and Source buttons to perform a reset.
 

If you suspect a printing error, please contact us. We will ask you take a photo of your Personalised Product. Then we can compare this to the confirmed order image. If the issue is verified, we will provide further instructions to have your Personalised Product re-printed.

The ergonomics of yurbuds sport earphones are indeed different and it is that unique design that creates the TwistLock™ and the guarantee that they will not fall out nor hurt. Our development team studied the human ear, and, as athletes, we know the demands on sport earphones. The results of that research are yurbuds. We encourage you to explore the various offerings on jbl.com.

Move the sub closer to the SOUNDBAR for testing and see if the signal picks up. 1: Turn off any wireless routers or devices that run on 2.4ghz signals, such baby monitors, cordless phones, etc. and test to see if the subwoofer connects. 2: Test with a movie or music with a lot of action scenes or bass. If it's just dialogue, you may not hear the subwoofer.

When you press the power button you will hear a “door locked” tone. This means the top capacitive touch buttons have been locked. At this point you cannot trigger them. With another short press of the power button, you will hear a “door unlocked” tone, which means the top capacitive touch buttons have been unlocked.

If your volume level is quiet, make sure that the TalkThru is not activated on your headphones. In order to deactivate or activate TalkThru, quickly press the ANC button located at the top of the LEFT ear cup. You will hear an audible voice stating, TalkThru On when activated, and 'ANC On' when deactivated.

There is a firmware update for the Tour One headphones, release notes below.

What’s New:
1. Optimize ANC performance at mid-range around 1kHz.
2. Optimize a few minor pop noises.
3. Fixed a few minor SW bugs.
4. Optimize the UI behavior.

To pause/play music, tap center button on right or left ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on right or left ear. Unfortunately, you cannot skip tracks backward.

To skip tracks forward, double click the PAUSE/PLAY to advance to the next track. Please note: You can only skip tracks forward. This speaker does not have the capability to skip to the previous track.