How To
How To
1102 results
-
Look at the back of the primary speaker, which is the one with pause/play and volume controls. You will see a switch called "mode". This switch can be in either S or P position. S stands for Secondary, P stands for Primary. Switch to Primary, and your speaker will now open Bluetooth and will accept analog signals. (The Secondary position is used for systems where four speakers are in use, since only one speaker can act as primary speaker.)Was this helpful? Thank you for your feedback!
-
The most important thing, is to be sure that both blue LEDs must flash quickly, one on the center speaker, one on the subwoofer. If just one of these LEDs does not flash quickly, pairing cannot take place. If it is difficult to make one of the LEDs change to quick flash, it may be that the button is held too long, or not pressed in the right angle. Try again with a short, firm press less then a second.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The JBL Free will automatically switch to mono mode on the RIGHT ear when the call starts. After the call ends stereo music mode will automatically resume.Was this helpful? Thank you for your feedback!
-
Android N, version 7.0 may have some compatibility issues, that are resolved with Android version 7.1. If your device is running Android N 7.0, please update it to 7.1 which should fix your issue.Was this helpful? Thank you for your feedback!
-
The registration success rate and quality of voice commands depends on the performance of your smart phone’s microphone. Make sure that your smart phone’s microphone is unobstructed and you are speaking clearly when registering commands. If you continue to have issues, try registering using a family member or friend’s smart phone as a test. If voice command registration is successful with their device, the microphone on your smart phone may have issues.Was this helpful? Thank you for your feedback!
-
Make sure your smart phone supports BLE (Bluetooth Low Energy) and it is connected to Smartbase via Bluetooth.Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB250 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB200 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
If I have a JBL Authentics L8 or L16 that is connected to Wi-Fi, do I need an Adapt to stream to it?Yes, you will need to connect an Adapt to stream music to the JBL Authentics products.Was this helpful? Thank you for your feedback!
-
When starting a workout in UA Record, the workout setup screen will display the heart rate monitor that is currently connected to your phone. Make sure your UA Sport Wireless Heart Rate are turned on and the logo is displaying in the heart rate monitor section.Was this helpful? Thank you for your feedback!
-
No, all recordings made on the telephone will be using the telephone's built-in microphone. Replay of the recording will be heard over the speaker afterwards, though, as long as it is paired to the telephone.Was this helpful? Thank you for your feedback!
-
During the design phase, it was decided to optimize BT reception, which is achieved by buffering digital signal streams. Since this takes a little bit of time, a slight delay will be the result. We have now optimized the software, so the lip-sync problem is no longer an issue. Video materials can now be watched with proper audio timing. Please check the product support page "downloads" tab for your headphone to check for the update files. If you experience delay, even after performing the update, please be aware that delays can occur for several reasons. For instance, the Bluetooth transmitter in a TV set can introduce delay. Also, some TV sets can cause timing changes if certain image processes are used. Try to disengage image processing, and check if lip-sync adjustment is available in your TV. With YouTube or other streaming services: In cases of lip-sync issues, it may also be a good idea to carry out a refresh of the source website. Always try more than one streaming source to determine if the delay comes from the streaming service or from you connection.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00