How To
How To
1102 results
-
With the headphone in OFF state, press and hold the ON/OFF button for about 7 seconds for the Everest, 16 seconds for the Everest ELITE models. (ELITE changes to 7 seconds as well from software 0.5.6). Bluetooth memory is now erased, and new pairings can be made. An ELITE headphone permits pairing with one source device at a time. If you do not want to do a complete reset as described above, you can use the following method. Without reset, ELITE will try to re-pair with the last source when switched ON. If the last source is not detected, maybe because you want to use another source device, switch the ELITE off and on again, and make sure that the last source device you used is no longer switched ON. This way the ELITE will not be able to "see" the old source, and it will search for a new one. Now the ELITE will again search for the last paired source, and since it cannot find it after some seconds, it will switch back to be open for pairing with a new source. The LED will blink red/blue as an indication of this. The Everest BT models permit pairing with two source devices simultaneously. If you have used both source pairings, and want to pair to a third source, please perform the reset as described above (hold the ON/OFF button for about 7 seconds with the Everest OFF). Now you can again pair two source devices.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold both volume buttons for more than 5 seconds.
Your headphones are now reset to factory status.
Was this helpful? Thank you for your feedback! -
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
- Turn the unit ON.
- Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
- Unit is now reset.
Was this helpful? Thank you for your feedback! -
Press Phone and "volume +" > 2 sec. Power must be on.Was this helpful? Thank you for your feedback!
-
We offer a 30 day free return period. To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.
Was this helpful? Thank you for your feedback! -
The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.Was this helpful? Thank you for your feedback!
-
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00