How To
How To
1102 results
-
The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.Was this helpful? Thank you for your feedback!
-
Yes you can wash it if the fabric is dirty. But remember to close the USB cover.Was this helpful? Thank you for your feedback!
-
Is Bluetooth APT X streaming supported by the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?The speaker uses Bluetooth version 4.2 but does NOT support APT X.Was this helpful? Thank you for your feedback!
-
This unit is fully dust-proof, and can withstand continuous immersion in water (up to 1.5 meters / 4.9ft for 30 minutes).Was this helpful? Thank you for your feedback!
-
This product is rated IP67, which is different from IPX7. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes. It is also resistant against dust. Dust accumulation around electronics can lead to hardware failure, so the IP67 rating is an extremely beneficial addition to this product.Was this helpful? Thank you for your feedback!
-
The amplifier has a signal sensor on the high-level (speaker level) inputs, so it is not necessary to use a trigger cable when input is high-level, and connected to the high-level inputs. However, low-level input signals through the RCA-phone input sockets do not activate a signal sensor, so use of a trigger cable is MANDATORY for low-level input signal use.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire/Focus 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
There can be differences in the internal hardware that also implies different firmwares. These products feature the same specifications and performance expectations. If the app does not inform you of any new updates, the firmware is current and the product is performing as designed.Was this helpful? Thank you for your feedback!
-
The new Boombox 2 does not feature the Indoor/Outdoor Mode. With the first generation Boombox, the Outdoor Mode was loud, but lacking sufficient bass. The Boombox 2 has both improved bass and loudness to create the perfect balanced sound for all environments.
Was this helpful? Thank you for your feedback! -
The system features an automatic mute function that becomes active after 10 seconds of no signal activity. Since the output level varies greatly between different genres and recording levels, it is highly recommended to set your source volume levels above 4, or preferably at mid-level, then controlling the listening level using the volume control provided in the speaker system.Was this helpful? Thank you for your feedback!
-
Often, hum is caused by a ground loop. This is a problem that is sometimes created when connecting two or more electrical components together. Sometimes the problem does not lie in any one particular unit, but in how they're connected. If your subwoofer is connected to a different wall outlet than your system, try to move the subwoofer plug to the same outlet. This may require an extension cord just for the trial. If it works, you can permanently move the sub or use an extension cord. However, if the hum you are hearing is coming from inside the sub, or if it is constant even when nothing is connected to the inputs of the sub, there is something wrong with the sub and you should bring it in for service.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00