How To
How To
448 results
-
The DUET NC noise cancellation button is located on the bottom Right ear cup. To turn the Active Noise Cancellation on, press and hold the button (Located next to the Bluetooth button) for 2-3 seconds or until you hear the confirmation audio tone. To turn off the noise cancellation, press and hold for 2 seconds or until you hear the audio tone powering off. A white LED next to the button lights up when NC is on.Was this helpful? Thank you for your feedback!
-
The E65BTNC noise cancellation button is located on the bottom Right ear cup. To turn the Active Noise Cancellation on, press and hold the button (Located next to the Bluetooth button) for 2-3 seconds or until you hear the confirmation audio tone. To turn off the noise cancellation, press and hold for 2 seconds or until you hear the audio tone powering off. A white LED next to the button lights up when NC is on.Was this helpful? Thank you for your feedback!
-
Press and hold the RIGHT center button for 1-2 seconds.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
-
The Reflect Contour BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
The Synchros Chrome is actually the Synchros S500 in chrome-plated version. On the right ear cup, you will find two ridges. These are there to make it possible to remove the disc that covers the batteries. You just position your fingernails against the ridges, to turn the disc counter-clockwise, against a small notch resistance. The Chrome is not painted, but plated. This means that the material is now thicker, and the lid can be rather difficult to remove, because the locking notches are squeezed into position. There is no other way than to put pressure on the ridges, press downward and in a counter-clockwise direction at the same time, and press until the notches, or claws, finally let go, and the lid rotates into open position, when it will fall off. If the lid does not budge, it may be necessary to use some kind of tool, but that can damage the chrome surface. In extreme cases, it may have to go to service.Was this helpful? Thank you for your feedback!
-
Press the power button located on the bottom of the Right Ear cup. If this is your first time using the headphones, it should immediately start looking for a device to connect to. Make sure that the device that you are trying to connect to is in pairing mode. The JBL JR300BT should display on your discoverable devices within 2-5 seconds. If the headphones have not successfully connected to the device, press and hold the Bluetooth button located next to the Power button on the Right Ear Cup for 2 seconds. As the headphones go into pairing mode, they should connect to your device within 2-5 seconds.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
-
Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The Reflect Contour headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.Was this helpful? Thank you for your feedback!
-
Press and hold the power button which is located on the right arm of the neck band. Press and hold for 3-5 seconds until you hear the audible voice state "Powering ON" followed by "Looking for device." Make sure the device you are attempting to connect to is in search mode and within bluetooth range. You will see Reflect Fit Audio on the discoverable devices. Choosing this option will allow you to receive audio playback.Was this helpful? Thank you for your feedback!
-
Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The DUET MINI headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.Was this helpful? Thank you for your feedback!
-
- Press the power button located on the top right of the speaker.
- If this is your first time pairing the device, the speaker will automatically go into pairing mode.
- Make sure that the product you are attempting to pair to is in search mode and in bluetooth range
- The Clip 3 should pop up on discoverable devices within a few seconds.
- Choose the Clip 3 option and you will be connected within a few seconds.
Was this helpful? Thank you for your feedback! -
To charge the Everest 110, slide the rubber window from the top down to expose the USB charging port that is located on the back of the inline microphone. Please use the JBL charging cable that was included in the packaging to charge these headphones.Was this helpful? Thank you for your feedback!
-
You can bend the ‘arms’ of the neck in and out to get the optimum fit for your exercise/level of activity. The flex zone is the black rubber part on the neckband.Was this helpful? Thank you for your feedback!
-
The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.Was this helpful? Thank you for your feedback!
-
Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.Was this helpful? Thank you for your feedback!
-
The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
(1) Select the JBL soundbar you want to rename
(2) Navigate to the Support tile and select "Rename My Product."
(3) Press the current name and type in the new name
(4) Press SAVEWas this helpful? Thank you for your feedback! -
Press and hold the multi-function button shown in “quick start guide” section 5 to ignore incoming call.Was this helpful? Thank you for your feedback!
