How To
How To
448 results
-
Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.Was this helpful? Thank you for your feedback!
-
To use the Spotify Connect feature for JBL Playlist, a premium Spotify account is required. Please visit www.Spotify.com/freetrial for 30 days of complimentary premium account trial for first time users.Was this helpful? Thank you for your feedback!
-
JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.Was this helpful? Thank you for your feedback!
-
1. Disconnect/unplug the product from the network cable. If dealing with a smartphone, forget the wi-fi on the phone. 2. Shut the router completely OFF. (do not reboot, you must turn it completely off) 3. Boot the router up and let it complete it's connection with everything, usually a few minutes. 4. Shut the router completely OFF, again. This is REALLY important. Before turning it off a second time, the router still has the product in it and is looking to connect to it. Shutting it off a second time allows the router to go through a complete power cycle without ever seeing the product, so it will remove it from its system. 5. Boot the router up, again, and let it complete it's connection with everything. 6. Now plug-in/turn on the product. The router should find the product and all should work. 7. If dealing with a smartphone, search for the wi-fi and reconnect to it. All should work after this.Was this helpful? Thank you for your feedback!
-
It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone. Was this helpful? Thank you for your feedback! -
This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products
Was this helpful? Thank you for your feedback! -
1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).Was this helpful? Thank you for your feedback!
-
Yes, you can adjust the game and chat audio balance by rotating the dial-up and down. When you rotate the dial, you'll feel a notch that indicates the balance is 50% game and 50% chat. The slider on Quantum ONE is different and has no notch but instead a visual indicator.Was this helpful? Thank you for your feedback!
-
Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.Was this helpful? Thank you for your feedback!
-
To show the current firmware version on your JBL TUNER device, go through the following steps.
- Turn on the JBL TUNER.
- Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
- In the display, you will see a combination of letters and numbers. This is the current software version.
- See picture below as illustration.
The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.
Was this helpful? Thank you for your feedback! -
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.
Check that the PC is using the correct recording device.
1. Go to Control Panel
2. Select Sound
3 Select Recording
4. Make sure to select the proper recording device.- Right-click on it Quantum headset.
- Now select "Set Default Device" or "Select Default Communication Device"
6. Go to Properties
7. Chose Levels and adjust accordinglyWas this helpful? Thank you for your feedback! -
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.
Check that the PC is using the correct recording device.
1. Go to Control Panel
2. Select Sound
3 Select Recording
4. Make sure to select the proper recording device.- Right-click on it Quantum headset.
- Now select "Set Default Device" or "Select Default Communication Device"
6. Go to Properties
7. Choose Levels and adjust accordinglyWas this helpful? Thank you for your feedback! -
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.
How to check your PC settings for the correct recording device
1. Go to Control Panel
2. Select Hardware and Sound
3. Click on Sound
3 Select Recording
4. Make sure to select the proper recording device.-
Right-click on it Quantum headset.
-
Now select "Set Default Device" or Select "Default Communication Device"
5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties
6. Choose Levels.
7. Adjust accordingly.
Please also make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's Game-Chat balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumEngine PC software.
If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumEngine software.
Finally, you can also do a short press on the Smart Ambient button on the headset (if your headset, has this feature)Was this helpful? Thank you for your feedback! -
-
- Power on your JBL LINK speaker.
- Verify that you are connected to the right Wi-Fi network on your smartphone.
- Open your Google Home app
.
- Enable Bluetooth
- Enable Location Service
(Android Only)
- Make sure you have permitted the Google Home app to view your location.
- First option
Tap Add
Set up device
Set up new devices in your home
- Second option
Tap
- Follow the instruction on screen to add your new JBL LINK speaker.
You are now all set and can enjoy your LINK device!Was this helpful? Thank you for your feedback! -
(1) Use JBL One App to set up the My Moment Feature.
(2) Select the JBL soundbar you want to set your favorite music to the My Moment feature.
(3) Tap the My Moment card to assign music.
(4) Click Add Music to manage music streaming services and specific music tracks.
(5) Set the timer to inactive speaker/soundbar (optional)
(6) Set the music loudness (optional)
(7) Press SAVEWas this helpful? Thank you for your feedback! -
With our JBL BAR 5.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings.
Let us walk through each one of them.
Resetting WiFi settings- Turn on your JBL BAR 5.1 Surround.
- Press and hold POWER button down for more than 10 seconds.
- All of your WiFi configuration is lost and you need to reinstall it again.
Resetting to Factory default settings- Turn on your JBL BAR 5.1 Surround
- Press and hold POWER and SOURCE button for 3 seconds.
- Your device is now reset.
Was this helpful? Thank you for your feedback! -
With our JBL BAR 9.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings. Let us walk through each one of them. Resetting WiFi settings Turn on your JBL BAR 9.1 Surround. Press and hold POWER button down for more than 10 seconds. All of your WiFi configuration is lost and you need to reinstall it again. Use the Google Home app to install the device on your WiFi network. Resetting to Factory default settings Turn on your JBL BAR 9.1 Surround Press and hold POWER and SOURCE button for 3 seconds. Your device is now reset. You can now start allover with installing your BAR 9.1 Surround.Was this helpful? Thank you for your feedback!
-
The factory reset button restores your device to the default settings, including network and audio configurations.
Please use one of the following solutions:- Press and hold VOL -, VOL +, and Source buttons on the device at the same time until the LED light flashes (hold for more than 5 seconds)
- Open your JBL ONE App.
- Navigate to the support tile.
- Select RESTORE FACTORY SETTINGS.
Was this helpful? Thank you for your feedback! -
To reset your JBL Bar 2.0 or 2.1 back to factory default settings, follow the steps below.
- Turn on your JBL Bar 2.0 or 2.1
- Press SOURCE and POWER buttons on top of the bar at the same time for more than 3 seconds.
- Your soundbar will now power off and on again.
Was this helpful? Thank you for your feedback! -
In order to reset the headphones:
Long Press of volume + and volume - at the same time while the unit is on. Make sure that bluetooth is NOT on and connected to any device.
When reseting, LED will blink faster.Was this helpful? Thank you for your feedback! -
Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.Was this helpful? Thank you for your feedback!
-
Resetting the Partybox to Factory Settings
- Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
- The JBL Partybox will power off and back on and is now reset.
Was this helpful? Thank you for your feedback! -
Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now resetWas this helpful? Thank you for your feedback!
-
In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.Was this helpful? Thank you for your feedback!
