In-Ear

  • Re-establishing Volume Levels/Balance between Earbuds
    As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds and your ears. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing.

    If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

    cleaning-earstick-tip 
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    How to Turn off your TWS Headphones
    1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).
    More FAQs
  • My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    How to Re-establish Advanced Swipe Controls Functionality
    To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
    After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
    The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.

    L300TWSFAQ.png
    Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings Settings.png once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.

    HPAPPSW1.png HPAPPSW2.png
    HPAPPSWIPE1.png HPAPPSWIPE2.png
     
    How to Perform a Hardware Reset
    To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
    * Location
    Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
    Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
    Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    More FAQs
  • Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
  • Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    How to clean your earbuds
                                                                                                 CLEANING THE PRODUCT V2.JPG
    CLEANING THE PRODUCT TWS.JPG  
    Use a clean cotton swab slightly moistened with alcohol to:
    1. Remove earwax and dirt from the ear tips on your earbuds.
    2. Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
    3. Clean the grooves on the cover and at the bottom of the charging case.
    After cleaning, make sure the charging case and earbuds are dry before putting the earbuds back into the charging case.

    TIP: 
    We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.
    How to Turn off your TWS Headphones
    1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).
    More FAQs
  • Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    Waterproof Information (IPX7)

    This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

    IPX7-icon.png
    How to Turn off your TWS Headphones
    1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).
    More FAQs
  • My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

  • UA Flash: Call Information
    To take a phone call, press the center button of the RIGHT ear for 1 second. To hang up a call, press and hold the center button on the RIGHT ear for 1 second. To ignore a call, press and hold center button for 3 seconds until music resumes.
    TalkThru Technology
    To activate TalkThru Technology, press the LEFT ear for a short press for 1 Second which allows you to clearly hear others for quick conversations without removing headphons. Music volume level should lower when TalkThru is engaged. Press again for 1 second to turn off Talk Thru.
    UA Flash: Charging Information
    To charge the UA Flash, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly: 0= 0% Dead 2-3 = 40%-50% 4=100% Full battery life
    UA Flash: Pairing to a different device
    To connect to a new device, begin with the headphones powered off and hold the center button on the RIGHT headphone for 5 seconds to enter pairing mode. You will hear the BT pairing audible chime as it searches for a different device. Make sure the device you are wanting to connect to is in range and BT is on. Once connected you will hear the audible Connected chime. Once Right ear is connected, press and hold the center button on LEFT ear for 3 seconds as it powers on and connects to the device followed by the same Connected audible chime.
    More FAQs
  • JBL Free: Manual Re-pairing to Bluetooth Devices
    In the event that ear pieces do not re-pair automatically to paired Bluetooth device, power off ear pieces individually by press and hold the buttons for 5 seconds. To enter Bluetooth pairing mode when ear pieces are powered off, press and hold on buttons of both earpieces for 8 seconds. Re-pair the right ear piece with desired Bluetooth device when LED indicator on right ear piece alternates between blue and white LED lights.
    JBL Free: Pairing Information
    Remove ear pieces from the case. Both ear pieces should automatically connect to each other. Wireless connections are automatically established when the headphones are taken out of the case. To pair to a different device, press and hold the Right ear piece for 5 seconds as it alternates between blue and white LED lights. Make sure that the device you are attempting to connect to is in pairing mode. The JBL Free should display on discoverable devices within 3-8 seconds. Choose JBL Free and the headphones will connect after you hear the audio confirmation tone.
    JBL Free: Manual Re-pairing Left & Right Ear Pieces
    In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.
    JBL Free: Sweat Proof
    The JBL Free has an IPX5 rating that helps protect the headphones from sweat and moisture.
    More FAQs
  • Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
  • Is it possible to turn off the blinking blue LED light from my headphones?
    No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.
  • Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    Is the Live 200BT waterproof?
    No. The Live 200BT does not feature any IPX rating so overexposure to both sweat and water can compromise the headphones.
    Can you take calls from the Live 200BT?
    Yes. To take a call from the Live 200BT press the center button located on the RIGHT neckband for 1-2 seconds. To hang up, simply press the center button again.
    More FAQs
  • Is there an app for the EVEREST Bluetooth models that are not one of the ELITE models with ANC?
    No, the app works with the ELITE models only. These are the ones that feature Active Noise Cancelling.
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    What is the requirement for the JBL Everest GA series?
    These are the supported languages for the Everest GA series.
    • English (US, UK, CA, IN, AU)
    • German
    • French (CA, FR)
    • Japanese
    • Portuguese (BR)
    More will be added in future Google releases.
    More FAQs
  • My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    How do I reset my JBL Everest 310, 710 and 750 Elite headphones?
    With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.
    Are the Everest 150NC waterproof?
    No. The Everest 150NC do not feature an IPX rating and are not designed to be overexposed to moisture. Overexposure can compromise the controls and sound.
  • How long can I listen to MP3 music with the Endurance Dive?
    You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of music
    How deep and for how long can I dive with my JBL Endurance DIVE?
    With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Can the Endurance Series be connected to more than one device at a time?
    The headphones can pair to multiple devices but can only be connected to one device at a time.
    More FAQs
  • How can I reset my JBL headphones?
    With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.
    Is it possible to turn off the blinking blue LED light from my headphones?
    No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.
    Reflect Mini 2: Pairing Information
    To connect to a different Bluetooth device, first switch the headphones off. Now press and hold the center button on the headphone remote control for about 3-5 seconds. You should see the light blinking red/blue to indicate pairing mode, and the voice prompt should state “looking for device”. You should see "Reflect Mini 2" appear on the source's BT list. Choose that option, and wait for the voice prompt to state “connected”
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    More FAQs
  • Is it possible to turn off the blinking blue LED light from my headphones?
    No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.
    Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    How do you skip tracks on the Reflect Contour?
    The Reflect Contour BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.
    More FAQs
  • Pairing issues with a Computer or PC
    In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

    The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

    • A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

    • AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

    Always get the latest driver version available for your Computer/PC/Laptop.

    To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

    The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
    Does the T110BT have volume control?
    Yes, the T110BT features a three button inline microphone which allows you to pause/play skip tracks, answer calls and control the volume.
    T110BT Headphones: Power and Pairing Information
    To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.
  • JBL Free: Manual Re-pairing to Bluetooth Devices
    In the event that ear pieces do not re-pair automatically to paired Bluetooth device, power off ear pieces individually by press and hold the buttons for 5 seconds. To enter Bluetooth pairing mode when ear pieces are powered off, press and hold on buttons of both earpieces for 8 seconds. Re-pair the right ear piece with desired Bluetooth device when LED indicator on right ear piece alternates between blue and white LED lights.
    JBL Free: Pairing Information
    Remove ear pieces from the case. Both ear pieces should automatically connect to each other. Wireless connections are automatically established when the headphones are taken out of the case. To pair to a different device, press and hold the Right ear piece for 5 seconds as it alternates between blue and white LED lights. Make sure that the device you are attempting to connect to is in pairing mode. The JBL Free should display on discoverable devices within 3-8 seconds. Choose JBL Free and the headphones will connect after you hear the audio confirmation tone.
    Is it possible to turn off the blinking blue LED light from my headphones?
    No. There is no way to turn off the blue LED light from our wireless headphones unless they are turned off.
    JBL Free: Manual Re-pairing Left & Right Ear Pieces
    In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.
    More FAQs
  • How do you power on and pair the JBL Reflect Fit headphones?
    Press and hold the power button which is located on the right arm of the neck band. Press and hold for 3-5 seconds until you hear the audible voice state "Powering ON" followed by "Looking for device." Make sure the device you are attempting to connect to is in search mode and within bluetooth range. You will see Reflect Fit Audio on the discoverable devices. Choosing this option will allow you to receive audio playback.
    How do I check my heart rate on the JBL Reflect Fit headphones?
    Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.
    Where is the Heart Rate sensor on the JBL Reflect Fit?
    The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.
    Reflect Fit Headphones: Track Control
    To skip the tracks forward, press and hold the volume up (+) button for 1-2 seconds and you will advanced to the next song. To start the current song you are listening to over, press and hold the volume down (-) button for 1-2 seconds. Please note: You can only advance to the next song be skipping forward, you cannot skip tracks backward. You can only restart the current song over by pressing the volume down (-) button.
    More FAQs
  • Does the T205 have volume control?
    No. Because it features a one button universal microphone, it does not give you the ability to control the volume.
    How do I skip tracks on the T205?
    Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.
    Does the T205 have a microphone?
    Yes, the T205 features a one button universal microphone that gives you the ability to pause/play, answer/hang up calls, and skip tracks.

Further Support

Watch & Learn

Have you seen our Youtube channel?

Many of our products have videos introducing them.

Learn more

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a product expert
Call us now at: +632 8 865 2317

Globe: +63 917 849 7697
Smart: +63 998 542 0234

Mon - Fri - 8:00 a.m 5:00 p.m (PHT)

E-mail Us

E-mail Us

365 days a year

We will respond within one business day.

Email Us
Chat with Us

Chat with Us

Mon - Fri - 8:00 a.m 5:00 p.m (PHT)

message

WhatsApp Us

Message us at +63 998 542 0234 or click here 

Mon - Fri: 08:00 a.m-05:00 p.m (PHT)