This headphone does not feature volume control. You must manually control volume from your device.

Yes, the Xtreme 2 features an IPX 7 rating. IPX7 is defined as the speaker can be immersed in water up to 1 meter for up to 30 minutes.

No. The 600BTNC headphone does not feature any IPX rating that protects it against sweat or water. Over exposure to water can compromise the controls on the headphones.

There is a Wi-Fi indicator on the back of the main speaker, and when it turns amber, it indicates that the Wi-Fi signal is weak. Try to move the speaker closer to your Wi-Fi router, and when the signal indicator turns White again, then it has a steady connection.

Yes, the cable has a one-button remote control and a microphone. This means that you can pause, resume play, you can pick up the phone and stop a call, and talk to other people through the microphone. There is no option to control music volume on the cable remote. That is only possible when using the Bluetooth system for wireless listening, with the volume buttons on the ear pod.

No, this cable is straight, with no remote control. The headphones have remote control buttons on the ear pods, which can be used when listening over Bluetooth wireless.

No, the app works with the ELITE models only. These are the ones that feature Active Noise Cancelling.

With the release of v.3.0 of the JBL Music app, owners of the JBL Authentics L8 and L16 are now greeted with a message that an update is available. If you own one of these speaker systems, and you know that it already supports Spotify Connect, the update firmware is already installed, and you can ignore this message. If your speaker system does not already support Spotify Connect, the update is available for you, but you cannot perform it yourself, it must go to a service center to be updated. Please contact Harman Helpdesk or the distributor in your country for advice regarding servicing.

No. The Live 200BT does not feature any IPX rating so overexposure to both sweat and water can compromise the headphones.

Yes, two flexible joints permit you to expand the collar to make it easier to place it around your neck.

No, it is compatible with PC and Mac, but not with PS4, XBOX One, Nintendo Switch or Mobile.

The JBL Flip 7 has an IP68 water and dustproof rating, meaning it's protected from water and dirt.

The speaker can be submerged in up to 1.5 meters of water for up to 30 minutes.

This model is not supported by the JBL Partybox App.

Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.

The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.

Please make sure that the audio out format is set to PCM in the TV. Dolby Digital or other surround formats will not work with the BTA 20 transmitter.

• Please check whether you connected JBL DRG with your smartphone and head unit via Bluetooth before, then power off the head unit. • If you have, wait 2 minutes for JBL DRG to reconnect to smartphone after power on. This is because JBL DRG will automatically search for the head unit, first then the smart phone.

It sounds like you are living in a country where Google Assistant has not yet been officially released. When Google releases the Google Assistant to more countries, the Everest GA headphones will open up for this feature. It may require a software update for this to happen. For now, you can use them as normal Bluetooth headphones and wait for the release to use the Google Assistant feature.

Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.

JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.

It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone.

This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products

Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off  and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.

To show the current firmware version on your JBL TUNER device, go through the following steps.

1. Turn on the JBL TUNER.
2. Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
3. In the display, you will see a combination of letters and numbers. This is the current software version.
4. See picture below as illustration.

The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.

 

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.



How to check your PC settings for the correct recording device
1. Go to Control Panel

2. Select Hardware and Sound

3. Click on Sound

3 Select  Recording


4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.

   

2. Now select "Set Default Device" or Select "Default Communication Device"

   

5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties


6. Choose Levels.


7. Adjust accordingly.
 

Please also make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's Game-Chat balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumEngine PC software.


If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumEngine software.


Finally, you can also do a short press on the Smart Ambient button on the headset (if your headset, has this feature)

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Chose Levels and adjust accordingly

Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select  Sound 

3 Select  Recording

4. Make sure to select the proper recording device.

1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"

5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Choose Levels and adjust accordingly

1. Power on your JBL LINK speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. Enable Location Service (Android Only)
   1. Make sure you have permitted the Google Home app to view your location.
6. First option Tap Add Set up device Set up new devices in your home
7. Second  option Tap X device found Select Home location
8. Follow the instruction on screen to add your new JBL LINK speaker.

You are now all set and can enjoy your LINK device!

In order to reset the headphones: 

Long Press of volume + and volume - at the same time while the unit is on. Make sure that bluetooth is NOT on and connected to any device. 
When reseting, LED will blink faster. 

Resetting the Partybox to Factory Settings

1. Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
2. The JBL Partybox will power off and back on and is now reset.

Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.

Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now reset

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

Finding the software version

1. Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
2. A voice will start prompting numbers which indicates the current software version.

NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.

We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.

Instructions below are for Android only

1. Open your Google Home app 
2. Enable Bluetooth  on your device.
3. Enable Location service  on your Android device.
   1. Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
   2. In case you denied access go to Settings  Apps  Google Home  Permissions  Allow to view Location.
4. When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
   1. Tap  the  located top right corner.
   2. In the pop-up menu press "Show MAC address" Write down the MAC Address.

You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.

Finding the MAC address after speaker is installed

1. Open your Google Home app .
2. Tap on  to view your home.
3. Find your room .
4. In the top right corner tap Settings icon .
5. ​Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.

In Power On mode, press and hold 'Volume+' together with 'Play/Pause' for more than 2 seconds. The speaker will power off and is now reset.

Bluetooth Pairing

1. Press the button on the Partybox to start the pairing process.
2. Grab your device.
3. Go to settings --> Bluetooth --> Enable Bluetooth -->
4. Find the Partybox speaker you want to establish a Bluetooth connection to.

        

5. You now have a successful connection and can stream your favorite music.
   1. NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
   2. To stop Bluetooth broadcasting then insert a USB device.

To control the Light show on your JBL Partybox device, simply press the dedicated "Light show" button located under the Bluetooth icon. There are 3 different light shows available when toggling through them, select your favorite one and have a blast. There is no app developed to control or modify these settings, all settings have to be done on the Partybox device.

1. Open the Google Home app 2. Select the LINK VIEW 3. Select SETTINGS. 4. There is a line that says Paired Bluetooth Devices. 5. When you select it, it gives you the option to ENABLE PAIRING MODE. 6. Use your voice - "Hey Google, Open Bluetooth" and LINK VIEW will enable Bluetooth connection. You can disable Bluetooth using "Hey Google, Close Bluetooth" Once you have enabled Bluetooth pairing mode on your LINK VIEW, simply go into your Bluetooth settings menu on your mobile device and connect.

With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.
 

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers.

The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.

You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.

You can connect 3 smart devices ( iOS or Android ) simultaneously by Bluetooth. One when connecting via AUX cable.

They support up to 8 paired devices without reset.

You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of music

By pressing and holding the Bluetooth and the Volume PLUS buttons at the same time. The software version is shown in the display.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.

The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.

While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.

With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.

The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.