Under Armour Headphones Wireless

The product is Water Resistant and Sweat Resistant, but you cannot swim with these headphones.

MapMyFitness is the World’s Largest Digital Fitness Community.

To pair a different Bluetooth device, make sure that the unit is turned off. You then must press and hold the center button for about 3-5 seconds. You should see the light blink red and blue while it is in pairing mode and the audible voice should state, “looking for device”. You should see UA BT Wireless pop up on the device that you are attempting to pair it with. Choose that option and wait for the audible voice to state, “connected”

Instructions are located on the back of the “Find Your Fit” insert in the product box. There will be a 15 Character Access Code printed on the insert card, or you can visit www.mapmyfitness.com/promo/UAWireless. If you are not a MMF Member you will need to register on the website before you can redeem your Access Code. If you are already a MMF Member with an Annual Premium Membership you can visit the link and use your code to renew for 1-Year when your membership is up for renewal. Refer to the expiration date on your Access Code to ensure that it does not expire. If you are a MMF Member with a monthly Premium Membership you can cancel your monthly premium and then visit the link to enter the 1-Year Access Code.

Yes. If neither the size 5 or size 7 enhancers provide a secure fit, our customer care team can send you a complimentary sizing pack with two additional sizes. Please email ua.jblsupport@harman.com to request yours today.

You should hear the audible voice stating ‘low battery’ when you have about 20 minutes left of battery life left on the UA WIRELESS headphones. If you have an Apple device, you will actually be able to see the battery life in the upper right hand corner of the device next to the BT symbol.

No, the case is NOT waterproof

Yes, Once you've added your UA Sport Wireless Heart Rate to the UA Record mobile app any workout started on your UA Band will automatically connect to the headphones if powered on and present. The Band will indicate the heart rate sensor is connected and begin showing your heart rate zones using the color LED on the side of the Band.

Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.

We recommend cleaning the earphones with audio or electronic wipes.

Although the product is Water Resistant and Sweat Resistant, continuous exposure to water over an extended period of time may damage your earphones.

To remove the enhancer, pinch the edge opposite of the sound tunnel between your thumb and forefinger and firmly pull up and off the ear bud. Replacement enhancers are specific to the left and right ear bud. An (L) or (R) and size indicator is located on the inside of the enhancer. When changing the enhancers, you must place the right enhancer on the right ear bud and the left enhancer on the left ear bud. Firmly grasp the earbud with one hand and align the sound tunnel of the enhancer with your other hand and stretch the enhancer up and over the top of the red earbud. Check the alignment of the sound tunnel to insure best sound performance. If sound is muffled or weak, check and rotate sound tunnel. Most people use the same size for Right and Left but it is possible to use different sizes because some ears are not symmetrical. - If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email ua.jblsupport@harman.com to request yours today.

The Bluetooth range varies. However, you should get up to 15 meters (just under 50 ft) when using the product indoors. If you are using the headphones outside, conditions vary based on surroundings and body mass. For the best connectivity results, please make sure that the device you are paired to is in the front of your body.

The device is charged by a standard micro USB charger. To charge the unit, gently pull out the rubber cover just below the light indicator on the left side of the inline mic. You will see the the charging cable end.

To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the UA WIRELESS headphone. Once you select that option, the audible voice should state, “connected”.