


JBL Endurance JUMP
Thông số sản phẩm
General Specifications
Kích thước driver (mm) | 10.0 |
---|---|
Mã IP | IPX7 |
Audio Specifications
Độ nhạy của driver ở 1kHz / 1mW (dB) | -20dB |
---|---|
Dải đáp ứng tần số động (Hz) | 20Hz–20kHz |
Trở kháng (ohms) | 16.0 |
Số lượng driver trên mỗi tai | 1.0 |
Control Connect Specifications
Cấu hình Bluetooth | HFP v1.6, A2DP v1.3, AVRCP v1.5 |
---|---|
Tần số Bluetooth | 2.402GHz-2.48GHz |
Module phát Bluetooth | GFSK, π/4DQPSK,8DPSK |
Công suất phát Bluetooth | 4 dbm |
Phiên bản Bluetooth | 4.2 |
Tài liệu & Tải xuống
Bảng thông số
Hướng dẫn nhanh
Bộ sưu tập







Video
Có cái gì trong hộp vậy
- Tai nghe
- 3 kích cỡ nút tai
- 1 x Bộ tăng cường
- Cáp sạc
- Túi đeo thể thao
- 1 x Phiếu bảo hành/ Cảnh báo
- 1 x Hướng dẫn an toàn/ QSG

Câu hỏi thường gặp & How-Tos
This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:
• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.
• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device
Always get the latest driver version available for your Computer/PC/Laptop.
To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.
The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
Không tìm được thứ bạn cần?
Gọi cho chúng tôi
Nói chuyện với chuyên gia về sản phẩm
(08:30 - 18:00)
Gửi email cho chúng tôi
365 ngày một năm
Chúng tôi sẽ trả lời trong vòng một ngày làm việc.