JBL Bar 2.1 Deep Bass
|Model||Bar 2.1 Deep Bass CNTR (Soundbar Unit), Bar 2.1 Deep Bass SUB (Subwoofer Unit)|
|Power supply||100 - 240V AC, ~ 50/60Hz|
|Total speaker power output (Max. @THD 1%)||300W|
|Output power (Max. @THD 1%):|
|2 x 50W (Soundbar); 200W (Subwoofer)|
|Transducer||4 x race track drivers + 2 x 1” tweeter (Soundbar); 6.5” (Subwoofer)|
|Soundbar and Subwoofer standby power||<0.5W|
|Operating temperature||0°C - 45°C|
|HDMI Video output (With Audio return channel)||1|
|HDMI Video input||1|
|Frequency response||40Hz - 20KHz|
|Audio inputs||1 Optical, Bluetooth, USB (USB playback is available in US version. For other versions, USB is for Service only.)|
|Dimensions (W x H x D):|
|965 x 58 x 85 (mm) / 38” x 2.28” x 3.35” (Soundbar);|
|240 x 240 x 379 (mm) / 8.9” x 8.9” x 14.6” (Subwoofer)|
|Weight||2.16 kg (Soundbar);|
|5.67 kg (Subwoofer)|
|Packaging dimensions (W x H x D)||1045 x 310 x 405mm|
|Packaging weight (Gross weight)||10.4kg|
Control Connect Specifications
|USB port||Type A|
|USB rating||5V DC/ 0.5A|
|Supporting file format||mp3, wav|
|MP3 Codec||MPEG 1 Layer 2/3, MPEG 2 Layer 3, MPEG 2.5 Layer 3|
|MP3 sampling rate||16KHz - 48 KHz|
|MP3 bitrate||80kbps - 320kbps|
|WAV sample rate||16KHz - 48 KHz|
|WAV bitrate||Up to 3000kbps|
|Bluetooth profile||A2DP V1.3, AVRCP V1.5|
|Bluetooth frequency range||2402MHz-2480MHz|
|Bluetooth Max. transmitting power||<10dBm (EIRP)|
|Modulation Type||GFSK, π/4 DQPSK, 8DPSK|
|5G Wireless frequency range||5736.35 - 5820.35MHz|
|5G Max. transmitting power||<9dBm (EIRP)|
|Modulation Type||π/4 DQPSK|
Documents & Downloads
Quick Start Guide
What’s in the Box
- Wireless subwoofer
- Remote control with batteries
- Power cords (up to 8pcs depending on region SKUs)
- HDMI cable
- Wall-mount bracket kit with screws
- Quick start guide
- Warranty card
- Safety sheet
FAQs & How-Tos
- Turn on your JBL Bar 2.0 or 2.1
- Press SOURCE and POWER buttons on top of the bar at the same time for more than 3 seconds.
- Your soundbar will now power off and on again.
Our JBL BAR 2.1 Deep Bass is an improvement to the BAR 2.1.
Here is what you will get extra:
- Improved sound quality.
- Deeper and richer bass.
- A new modern design change.
If you have a mesh network (more commonly seen in Eero Mesh networks), it is possible that you may experience your satellite speakers or subwoofer intermittently disconnecting from the soundbar. This is similar to normal interference that occurs with products on a similar wireless frequency. The special thing about Eero mesh networks is that they do not allow you to move a device to the 5Ghz or 2.4Ghz band. The system will automatically decide which devices should be on which band and will move them accordingly (switching whenever needed). Some of our soundbars run on a 5Ghz frequency which is where the interference can occur. Since we cannot change the signal in which they operate and we cannot change the band they are connected to via their Eero mesh network, there are a few things you can do to try and stop this from occurring.
- Move the mesh nodes far away from the soundbar
- Use the 2.4Ghz band instead of the 5Ghz band (if your mesh system allows this)
- Ensure to enable/utilize the MU-MIMO setting (not applicable to all mesh systems). Please refer to your router's website to see if MU-MIMO is being utilized by default.
What is MU-MIMO?
MU-MIMO stands for Multi-User, Multi-Input, Multi-Output. This allows for the router to send a signal to multiple devices at one time vs. the previous version in which the router would be able to connect to multiple devices, but only send the signal to one device at a time.
NOTE: You may notice that when the soundbar is turned on, there may be a dip in the immediate internet speed, but it will go back to normal within less than a minute.
Can’t find what you’re looking for?
Talk to a product expert
Call us now at: (800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (EST)
Sat - Sun: 9:00 am - 5:00 pm (EST)
Chat With Us
Mon - Fri - 9:00 a.m 11:00 p.m (E.T)
Sat - Sun - 9:00 a.m 5:00 p.m (E.T)