How To
How To
1217 results
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
No, your subwoofer is not defective at all! This is normal and by design of the product after it has been paired for a longer period of time.Was this helpful? Thank you for your feedback!
-
There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now.Was this helpful? Thank you for your feedback!
-
No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.Was this helpful? Thank you for your feedback!
-
In order to get the earbuds to power on, please remove the plastic film to allow the pins in the charging case to make contact with the contact plates on the earbuds.
Was this helpful? Thank you for your feedback! -
- Ensure that your JBL One app device is less than 10m/33ft from the speaker during the initial set-up.
- Ensure it is plugged into power and the power LED is illuminated.
- Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
- Temporarily relocate either the speaker or router so that they are closer together. If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
- Try using a different device with the JBL ONE app installed and connected to your home network.
Was this helpful? Thank you for your feedback! -
It is usually not necessary to replace an unresponsive remote control. First, check to see if there is a small plastic tab extending out of the base of the remote control. This is a protective sleeve installed on new remote controls to prevent the battery from draining. Pull this tab to remove the plastic sleeve. The sleeve must be removed before the remote will operate. If the sleeve was removed or not present and the remote control is not working then a new battery should be installed before replacing the remote control. There is a small slide out drawer that houses the battery. The battery type will be either CR2025 or CR2032 for remotes of this size. Replacement batteries are commonly available from most electronic and convenience stores that sell small batteries. Check the number on the original battery and replace it with a battery that uses the same number. These steps will typically solve the problem.Was this helpful? Thank you for your feedback!
-
This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.Was this helpful? Thank you for your feedback!
-
There are two ways to blow speakers. The first is the one we all know and understand. If you pump 500 watts into a speaker that is only rated at 100 watts, kaboom, it blows up. As a result, very few of us do this. So then why are all of these poor, helpless speakers blowing up? Because of the second reason, under-powering. It's really a misleading term, but let's try to explain. First let's take it to the maximum. Example: You have a 1000 watt speaker and a 100 watt amplifier. The way you like to listen to music requires 300 watts. Typically, you will ask your amp to put out that 300 watts that you want to hear. The amp will do it, but it will clip and distort. Unfortunately, the human ear can't hear distortion until it reaches almost 10%. By that time it's usually too late. The speaker keeps trying to reproduce this distortion that it's not capable or reproducing and eventually it blows (usually the tweeter fails first). If you are blowing speakers with an amp that has a power rating lower than your speakers, you are pushing your amp too far, causing it to clip, and blowing speakers. If you are pushing your system too hard, it is suggested that you realize your systems limitations or recommend that you get a more powerful amplifier. Please realize, if you only buy speakers that will handle more power and not a more powerful amplifier, you won't solve the problem. The speakers will still blow, because it is distortion that is blowing them, not too much power.Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speaker has two different patterns for switching on, when using either battery or AC power. When using battery, turning on one speaker in either stereo mode or association mode (4 speakers connected), all will turn on simultaneously, no matter which is primary or secondary. When connected to AC power, switch on the primary speaker in stereo or associated mode, and the secondary speakers will follow. If you have associated speakers stereo or 4 speakers connected, then you have to press primary speaker's power button for more than 2 seconds, then the primary will send signal to secondaries, and they will wake up. It takes approx. 30-60 seconds before all are switched on. If your press it too short (less than 2 seconds), the primary speaker will not "pair" the secondary speakers together. Switch off the primary and start over again.Was this helpful? Thank you for your feedback!
-
Some mobile phones, tablet computers or laptop computers will react to the powerful magnetic field from the loudspeaker drive units that are right beneath the top panel. Some have magnetic sensors built in, which means that covers with magnets in the lid can turn the phone ON when the cover lid is opened, and turn it OFF again when the lid is closed. Such phones may turn off if placed on certain portions of the top panel. Other devices are simply sensitive to magnetic fields. You can move the device around on the top of your L8 or L16 speaker, to check if some locations are better than others. The magnetic fields are most powerful near the front panel, where the speaker units are mounted. If you cannot find a location which works, your particular phone, tablet or laptop cannot be used while resting on the top panel of your speaker. There are no reports of damage to any devices because of this phenomenon.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)