How To

Support Overview / How To

How To

1217 results
  • My device is waterproof, but what about salt water or chlorine water?
    Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.
  • My earbuds are disconnected for the left & right, what could I do?
    1. Insert both earbuds into the charging case.
    2. Try to click 5 times on both left and right earbuds button simultaneously, to reconnect left and right earbuds.
     
  • My Flip 3 does not respond after update. What can I do?
    Try below steps. Attach the charger so the device is charging. While charging: First try to hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds (this resets the Flip 3 to factory settings). If this does not help, press and hold the "Volume +" and "Link" buttons for more then 10 seconds (this will exit demo mode). As a last step, short press on the "Volume -" & "Volume +" & "Phone" buttons. If the device will still not turn on, it has a defect.
  • My Flip3 got dirty after a day on the beach. Can I rinse it under the faucet or shower?
    Yes, rinse it under a faucet or under the shower, but not under full water pressure.
  • My friend spoke one of my registered commands, but Smartbase does not respond.
    Voice commands can only be triggered by the user who registered them during setup.
  • My hair or cap activates the touch system on my Reflect Response. How can I avoid this?
    A certain degree of sensitivity is necessary to make the response system function. In some cases, hair or a cap touching the sensor plates can activate the system, even if you do not want it. The solution is to lock the sensor system. Put your finger on the left sensor plate, and hold it there for more than 4 seconds. Now the sensors are locked, and the problem is solved. Unlocking is done the same way.
  • My headphones told me heart rate disconnected. How do I reconnect it?
    Tap-hold on the right ear bud forcefully to reconnect heart rate. If this does not work, Hold the middle button to turn off, then back on your headphones.
  • My JBL GO goes into standby when I play quietly. Why is that, and can something be done to change this?
    With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.
  • My JBL Headphones App - Available DJ Signatures
    Some of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.

    See the release notes for app version 4.10.9 below:
    - Adding support for TOUR PRO+ TWS and TOUR ONE Global version
    - Removing expired DJ’s signatures
  • My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
  • My JBL LINK 10,20,300 or 500 does not show up my Apple iOS device, how come?
    To install your JBL LINK speaker using Apple iOS... 1. Download the Google Home app. 2. Activate your Bluetooth connection, as it is required for Apple devices. 3. Follow the instructions in the Google Home app.
  • My JBL LINK 10 or LINK 20 does not remember my Wi-Fi, how come?
    Sounds like your JBL LINK 10 or LINK 20 has been connected to another Wi-Fi network. It is very simple to reconnect to your Wi-Fi by using the Google Home app. Simply select your Wi-Fi in the app, and you're all set. All information about the speaker and voice teaching is stored in the Cloud, so you do not have to do this again.
< 1 ... 65 66 67 68 69 ... 102 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a support agent
Call us now at: (800) 336-4525

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat With Us

Chat With Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)