How To
How To
1217 results
-
In the Owner's Manual, we say "Up to 30 m (between primary and secondary speakers)". This applies to an ideal setup, with no obstacles and interference, and if there is interference at this distance, you will have to reduce the distance between the speakers. Please check for any objects and obstacles that could cause interruptions.Was this helpful? Thank you for your feedback!
-
When the secondary speaker gets out of range, audio disappears, but there is no indication that the transmission is out of range, other than silence. Once they get within range again, the front panel LED blinks a few times, indicating that connection has been re-established. During normal operation, random blinking can be experienced, which is an indication of the wireless link having recovered from interference.Was this helpful? Thank you for your feedback!
-
The quality of content depends on your Internet bandwidth. The minimum Internet speed is at least 25Mbps (megabit per second) or above for the best performance.
When using the LINK BAR to the WiFi router, always use 5 GHz WiFi band for highest performance at any time.
If you are still struggling with the quality of your content, then we have added an Ethernet port (LAN connection), which allows you to wire the LINK BAR for a steadier connection and performance.
More actionable advice:- Limit your device(s) at night or when you are streaming content that requires the best performance possible!
- Upgrade older product that could cause slow data transfer.
- Move devices that are capable of connecting to 5 GHz WiFi and leave "Legacy" product on 2.4 GHz only.
- Upgrade your router. Upgrading to a newer generation router is cheap and effective way to improve your home network in every way. It provides both a better Wi-Fi range and stronger signal.
- We are recommending that you go for a mid to high-level Wi-Fi router.
Was this helpful? Thank you for your feedback! -
When using an Android device, you need to have location service active on your phone or tablet and make sure that you allowed "Google Home app" to use the phone or tablet location service. However, make sure your Wi-Fi router has UPnP enabled and that you do not use any network extenders while connecting the product.Was this helpful? Thank you for your feedback!
-
Often, hum is caused by a ground loop. This is a problem that is sometimes created when connecting two or more electrical components together. Sometimes the problem does not lie in any one particular unit, but in how they're connected. If your subwoofer is connected to a different wall outlet than your system, try to move the subwoofer plug to the same outlet. This may require an extension cord just for the trial. If it works, you can permanently move the sub or use an extension cord. However, if the hum you are hearing is coming from inside the sub, or if it is constant even when nothing is connected to the inputs of the sub, there is something wrong with the sub and you should bring it in for service.Was this helpful? Thank you for your feedback!
-
The system features an automatic mute function that becomes active after 10 seconds of no signal activity. Since the output level varies greatly between different genres and recording levels, it is highly recommended to set your source volume levels above 4, or preferably at mid-level, then controlling the listening level using the volume control provided in the speaker system.Was this helpful? Thank you for your feedback!
-
The new Boombox 2 does not feature the Indoor/Outdoor Mode. With the first generation Boombox, the Outdoor Mode was loud, but lacking sufficient bass. The Boombox 2 has both improved bass and loudness to create the perfect balanced sound for all environments.
Was this helpful? Thank you for your feedback! -
There can be differences in the internal hardware that also implies different firmwares. These products feature the same specifications and performance expectations. If the app does not inform you of any new updates, the firmware is current and the product is performing as designed.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire/Focus 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the Inspire 500 Wireless headphone. Once you select that option, the audible voice should state, “connected”. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible voice stating, “powering on….looking for device” You will see the Bluetooth light alternate between red and blue when it is in pairing mode. Once connected the Bluetooth will change to a flashing LED light and the audible voice will state, “connected”.Was this helpful? Thank you for your feedback!
-
The amplifier has a signal sensor on the high-level (speaker level) inputs, so it is not necessary to use a trigger cable when input is high-level, and connected to the high-level inputs. However, low-level input signals through the RCA-phone input sockets do not activate a signal sensor, so use of a trigger cable is MANDATORY for low-level input signal use.Was this helpful? Thank you for your feedback!
-
This product is rated IP67, which is different from IPX7. IP67 protects the product from submersion in 1 meter (3.3 feet) of water for up to 30 minutes. It is also resistant against dust. Dust accumulation around electronics can lead to hardware failure, so the IP67 rating is an extremely beneficial addition to this product.Was this helpful? Thank you for your feedback!
-
This unit is fully dust-proof, and can withstand continuous immersion in water (up to 1.5 meters / 4.9ft for 30 minutes).Was this helpful? Thank you for your feedback!
-
We use a sophisticated vetting process to ensure that your image does not contain copyrighted, protected, sexual, suggestive, offensive or inappropriate elements. This includes words and messages. If these algorithms are triggered, your order is automatically cancelled. Please try again with a different image or wording.Was this helpful? Thank you for your feedback!
-
Is Bluetooth APT X streaming supported by the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?The speaker uses Bluetooth version 4.2 but does NOT support APT X.Was this helpful? Thank you for your feedback!
-
It will not damage the battery that power supply is connected all the time.Was this helpful? Thank you for your feedback!
-
Yes you can wash it if the fabric is dirty. But remember to close the USB cover.Was this helpful? Thank you for your feedback!
-
The lights cannot be adjusted by user. The digital front panel display has automatic light intensity adjustment, which follows the level of light in the room.Was this helpful? Thank you for your feedback!
-
The JBL Bar 300 does not support a subwoofer. Alternatively the JBL Bar 500 has a wireless subwoofer included.Was this helpful? Thank you for your feedback!
-
The JBL Bar 500 does not support rear/surround speakers. Alternatively the JBL Bar 800/1000 has detachable wireless rear speakers included.Was this helpful? Thank you for your feedback!
-
Yes, but only via cable, and noise cancelling cannot be activated meanwhile. Since the charging socket is located on top of the ear pod, adjustment is limited in that direction while the micro-USB plug is inserted.Was this helpful? Thank you for your feedback!
-
Yes, they are quite easy to remove, and with a little care, new ear pads can be fitted in one or two minutes. You can do this yourself.Was this helpful? Thank you for your feedback!
-
Yes, press Volume + and Surround button at the same time for 5 seconds.Was this helpful? Thank you for your feedback!
-
Yes, this can be done very easily by doing the following procedure: 1: Power on the Cinema Base. 2: Simultaneously press the “Surround” and “VOL –” buttons (at the same time). 3: The Cinema Base source LED button will light amber in color, for 1 second, then the power button LED light will go off and on. 4: Your Cinema Base is now reset.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)