How To
How To
1217 results
-
If the pairing mode is not succesful, please move the subwoofer closer to your SB150. The pairing process can take up to 30 seconds before a connection has been established.Was this helpful? Thank you for your feedback!
-
Try resetting the device, and remove the Bluetooth device on your source device in the settings. Now Bluetooth-pair with it again. If the unit still does not work as intended, please contact our helpdesk.Was this helpful? Thank you for your feedback!
-
As shown in the owner's manual, the "X" on the secondary speaker's rubber band is the power button.Was this helpful? Thank you for your feedback!
-
Look at the back of the primary speaker, which is the one with pause/play and volume controls. You will see a switch called "mode". This switch can be in either S or P position. S stands for Secondary, P stands for Primary. Switch to Primary, and your speaker will now open Bluetooth and will accept analog signals. (The Secondary position is used for systems where four speakers are in use, since only one speaker can act as primary speaker.)Was this helpful? Thank you for your feedback!
-
The most important thing, is to be sure that both blue LEDs must flash quickly, one on the center speaker, one on the subwoofer. If just one of these LEDs does not flash quickly, pairing cannot take place. If it is difficult to make one of the LEDs change to quick flash, it may be that the button is held too long, or not pressed in the right angle. Try again with a short, firm press less then a second.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The JBL Free will automatically switch to mono mode on the RIGHT ear when the call starts. After the call ends stereo music mode will automatically resume.Was this helpful? Thank you for your feedback!
-
Android N, version 7.0 may have some compatibility issues, that are resolved with Android version 7.1. If your device is running Android N 7.0, please update it to 7.1 which should fix your issue.Was this helpful? Thank you for your feedback!
-
The registration success rate and quality of voice commands depends on the performance of your smart phone’s microphone. Make sure that your smart phone’s microphone is unobstructed and you are speaking clearly when registering commands. If you continue to have issues, try registering using a family member or friend’s smart phone as a test. If voice command registration is successful with their device, the microphone on your smart phone may have issues.Was this helpful? Thank you for your feedback!
-
Make sure your smart phone supports BLE (Bluetooth Low Energy) and it is connected to Smartbase via Bluetooth.Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB200 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
Make sure the optical connection is seated securely on the SB250 and on your device. Go into your device settings and make sure the digital output is enabled. On TV displays the option usually states "enable external speakers" or enable "digital audio output".Was this helpful? Thank you for your feedback!
-
If I have a JBL Authentics L8 or L16 that is connected to Wi-Fi, do I need an Adapt to stream to it?Yes, you will need to connect an Adapt to stream music to the JBL Authentics products.Was this helpful? Thank you for your feedback!
-
When starting a workout in UA Record, the workout setup screen will display the heart rate monitor that is currently connected to your phone. Make sure your UA Sport Wireless Heart Rate are turned on and the logo is displaying in the heart rate monitor section.Was this helpful? Thank you for your feedback!
-
No, all recordings made on the telephone will be using the telephone's built-in microphone. Replay of the recording will be heard over the speaker afterwards, though, as long as it is paired to the telephone.Was this helpful? Thank you for your feedback!
-
If any of the items we deliver are damaged or incorrect, we will refund the delivery charge. If you change your mind about wanting to keep them, you may return them at no charge, but we will not refund the original delivery charge.Was this helpful? Thank you for your feedback!
-
This product carries manufacturer's warranty according to local regulations, but it cannot be repaired. Exchange is the only option.Was this helpful? Thank you for your feedback!
-
During the design phase, it was decided to optimize BT reception, which is achieved by buffering digital signal streams. Since this takes a little bit of time, a slight delay will be the result. We have now optimized the software, so the lip-sync problem is no longer an issue. Video materials can now be watched with proper audio timing. Please check the product support page "downloads" tab for your headphone to check for the update files. If you experience delay, even after performing the update, please be aware that delays can occur for several reasons. For instance, the Bluetooth transmitter in a TV set can introduce delay. Also, some TV sets can cause timing changes if certain image processes are used. Try to disengage image processing, and check if lip-sync adjustment is available in your TV. With YouTube or other streaming services: In cases of lip-sync issues, it may also be a good idea to carry out a refresh of the source website. Always try more than one streaming source to determine if the delay comes from the streaming service or from you connection.Was this helpful? Thank you for your feedback!
-
Yes, if you are using our new feature JBL Conncet. It will allow up to two products that have this feature, to be connected together. Connect to one of your speakers via Bluetooth or AUX source, press the JBL Connect button on the speakers. A sound will come when they are connected. You are now able to see them connected in the JBL Connect app.Was this helpful? Thank you for your feedback!
-
Yes, the SB 450 supports the JBL Connect feature but only to stream audio through Bluetooth. Please note, the JBL Portable app will not work with this speaker, nor will it support stereo music playback when linking two SB 450s together.Was this helpful? Thank you for your feedback!
-
When using the Boost TV as single device, it can have up to 3 Bluetooth connected devices attached. Once you are activating JBL Connect, it can only have one active Bluetooth source connected. To be able to use a different Bluetooth source, please turn off Bluetooth on your current connected device, and then press Bluetooth button on the Boost TV to enter pairing mode. Your new Bluetooth device are now connected and in control of the music.Was this helpful? Thank you for your feedback!
-
• Please check whether you connected JBL DRG with your smartphone and head unit via Bluetooth before, then power off the head unit. • If you have, wait 2 minutes for JBL DRG to reconnect to smartphone after power on. This is because JBL DRG will automatically search for the head unit, first then the smart phone.Was this helpful? Thank you for your feedback!
-
Close and restart the Google Home app, or restart your phone. Start the Google Home app again, and the speaker should now appear.
Was this helpful? Thank you for your feedback! -
Please make sure that the audio out format is set to PCM in the TV. Dolby Digital or other surround formats will not work with the BTA 20 transmitter.Was this helpful? Thank you for your feedback!
-
Our Control X Wireless speakers use Wi-Fi 2.4 GHz network to connect them. If there are any obstacles or people blocking the connection, it can cause interference. We suggest positioning the speakers on a high-level surface or shelf, to avoid any interference.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)