Press and hold the Microphone Mute button for >13 seconds

Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.

We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.

Instructions below are for Android only

1. Open your Google Home app 
2. Enable Bluetooth  on your device.
3. Enable Location service  on your Android device.
   1. Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
   2. In case you denied access go to Settings  Apps  Google Home  Permissions  Allow to view Location.
4. When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
   1. Tap  the  located top right corner.
   2. In the pop-up menu press "Show MAC address" Write down the MAC Address.

You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.

Finding the MAC address after speaker is installed

1. Open your Google Home app .
2. Tap on  to view your home.
3. Find your room .
4. In the top right corner tap Settings icon .
5. ​Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.

Finding the software version

1. Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
2. A voice will start prompting numbers which indicates the current software version.

Playing local playlist that you created via Spotify works differently for Android TV system, which the LINK BAR has built-in!

Here is how to do it:

1. Go to the Google Play Store on your TV screen (Use remote to navigate).
2. Download the Spotify app
3. Sign-in with your account.
4. You can use the dedicated app and navigate through your playlist.
5. Alternatively, you can now use voice commands such as "Ok Google, Play my Playlist Sunday Funday On Spotify"

Now you can enjoy Spotify using voice or the Remote Control.

*Some commands may not be available in all countries.

JBL TOUR ONE
Power off Tour One first and hold the ambient aware button on the left earcup for 2 seconds. You can get ANC on without Bluetooth connection, which will save your battery. Once you slide up the button on the right ear cup to power on, Bluetooth connection and music will return to normal.

 

JBL TOUR PRO+ TWS
Press and hold both right and left earbuds on Tour Pro+ TWS for 5 seconds at the same time. You can get ANC on without Bluetooth connection, which will save your battery. Once you press and hold both right and left earbuds for 5 seconds, Bluetooth connection and music will return to normal.

 

In case one of the earbuds loses its connection, you can do a manual pairing process by following the instructions below.

1. You can manually pair your earbuds by placing both back into the charging case and closing the lid.
2. Open the lid again, take them out of the charging case, and tap 3 times on each earbud simultaneously until you see the purple LED flash.
3. You will see the earbuds enter into Bluetooth pairing mode, and the connection between the Left and Right earbud is successful.

1. Press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The software version will scroll across the front display.
2. If a newer software version is available, download it from the JBL website.
3. Copy the two files to the Root directory of an empty USB thumb drive.
   • Update.zip
   • Checksum.txt
4. On the bar, press and hold the [POWER] and [SOURCE] buttons for more than 10 seconds.  This will reset the BAR 5.1 Surround.
5. Insert the USB thumb drive into the USB port on the rear panel of the bar.
6. On the bar, press and hold the [POWER] and [VOL-] buttons for more than 10 seconds to begin the software update process.
7. "UPDATING" will appear on the front display of the bar.
8. Wait for the software update to complete.  The unit will reboot and go back to standby.
9. Turn unit on.
10. Press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The new software version will scroll across the front display.

 We strongly recommend that you use the original packaging with the existing shock-absorbing packaging material.

Don’t have the original packaging?

Please follow these important guidelines to ensure that you pack the device safely and avoid shipping damage.
 

• Never use bubble-wrap only.
• Choose a sturdy cardboard box that permits at least 10cm of packaging materials between the device and the walls of the box. Putting the device into a cardboard box without proper shock-absorbing packaging materials will result in damage to the device.
   Air-bubble isolation and foam beans is advisable only for very light-weight items.
• Use packaging materials that cannot move around, and cannot be damaged by the device moving around and being shaken about.

 

We included a Remote Control in your box (I know, that's sweet of us), and you need to pair it with your LINK BAR before it is working.

This is how you will do it

1. Press the BLUETOOTH button on the LINK BAR
2. Now hold the BLUETOOTH button down for 3-5 seconds.
3. When you see "SEARCHING FOR ACCESSORIES" on your TV screen, release the BLUETOOTH button.
4. On your REMOTE press the HOME and BACK buttons at the same time.
5. A Green LED light will flash on the REMOTE to indicate that it is in pairing mode.
6. Keep holding down the buttons until you see a message on the TV screen that says, "Pairing remote control to LINK BAR" After 10 seconds, release.
7. If done successfully on your TV screen, you will see an indicator counting down that it will "pair" with your remote.

Enjoy your entertainment with few clicks away!

BONUS TIP:  There is an Android app called Android TV that will turn your Smartphone into a Remote controller.

If you want to add more depth and bass to your LINK BAR, we have a dedicated subwoofer (not included with the LINK BAR) that you can purchase!

Pairing the Subwoofer is very simple:
1. Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly.
2. Press the “Subwoofer Pairing” button on the SW10 subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly.
3. Press the “Subwoofer Pairing” button on LINK BAR, the LED indicator on the LINK BAR blinks rapidly
4. If successful, the pairing LED indicator on both subwoofer and LINK BAR will be a steady white LED light. If pairing fails, the sign on the subwoofer blinks slowly.
5. If the pairing fails, repeat the steps above. If you are still experiencing problems, please try to switch off all wireless devices in the home (such as routers, TV sets with wireless function, telephones, computers, etc.), then try again. It may be overcrowding on the 5GHz frequency, which often causes problems. By eliminating all other wireless activity, this will help space for the LINK BAR to establish its connection. You now should be able to pair without problems. Once pairing is complete, you can switch your devices on again

To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.

You will see a notification in the recommendation option on your TV screen when there is an upgrade is available.

The system will download the firmware and apply the update after your confirmation.

You can also manually check for updates. Go to the settings menu and select “About” followed by “System Update.”

Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.

The calibration is done in two steps: Listening zone & Speaker position

Calibrate the listening zone

1. Place the detachable rear speakers beside your seating position.

2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.

Calibrate the speaker position

1. Place the detachable rear speakers in your desired location.

2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).

NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.

This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.

USB Stick

1. Get an empty stick with speed of 2.0.
2. Make sure it is formatted with FAT16 or FAT32.
3. Your Music files can only be:  (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
4. The Partybox supports up to 8 subfolders.
5. It will be played in alphabetic sequence with main folders first then subfolders.
6. To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.

Playing music over Bluetooth connection is very simple to do:

1. Short press the dedicated Bluetooth button on the LINK BAR.
2. Go to settings on your phone.
3. Find Bluetooth and enable it.
4. Select the JBL LINK BAR in your device list.
5. You are now paired and ready to jam your favorite music!

If you are experiencing issues with the speakers turning off automatically while in use, try the following to resolve the issue (PC only):

• Enter 'Device Manger' in the Windows search bar (the magnifying glass icon at the bottom left of the taskbar in Windows 10), it should now appear in the search results under Control Panel.
• In the Device Manger list, navigate to your Universal Serial Bus Controllers, then select the 'USB Root Hub' device, right click it and select Properties.
• In the 'USB Root Hub' Properties select 'Power Management' from the options at the top, now turn off the setting 'Allow the computer to turn off this device to save power'.

The steps above may also solve issues relating to audio dropouts.

(1) On the subwoofer's rear panel, press and hold the pairing button until the LED  turns fast, flashing white.
(2) To enter the subwoofer pairing mode on the soundbar, press and hold the bass button on the remote control for more than three seconds. Then, press VOL - on the remote control.

On the soundbar LED display:
→ "SUB PAIRING": The subwoofer is ready for pairing.
→ "SUB PAIRED": The subwoofer is connected.

Please go to this Youtube address to watch an instruction video about how to record sound effects on JBL PartyBox 1000: https://www.youtube.com/watch?v=vcuIPVfnC8Q&list=PLPlXZNivfAs4mndPKnjUkB2ZggcA4cZvc&index=6&t=0s

To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.


Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings  once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.

What You Will Need

1x Pair of Replacement Ear Cups (Part Numbers Below) 
1x Medium to Large slotted Screwdriver

Everest 300/Elite 300
SC-HM20000200-B  LEATHER CUSHION (R) BLACK 300NXT
SC-HM20000100-B LEATHER CUSHION (L) BLACK 300NXT
SC-HM20000500-B LEATHER CUSHION (R) WHITE 300NXT
SC-HM20000400-B LEATHER CUSHION (L) WHITE 300NXT

Everest 700/Elite 700
SC-HM21000200-B LEATHER CUSHION (R) BLACK 700NXT
SC-HM21000100-B LEATHER CUSHION (L) BLACK 700NXT
SC-HM21000800-B LEATHER CUSHION (R) WHITE 700NXT
SC-HM21000700-B LEATHER CUSHION (L) WHITE 700NXT

Removing the Ear Cups

1. Place the headphones on a table and while holding the ear cup with one hand gently and slowly insert the tip of the screwdriver between the ear cup and headphones.
2. Once inserted gently twist the screwdriver until there is a slight separation between the ear cup and the headphones. Note: Do not twist the screwdriver too much as this may damage the headphones.
3. Continue step 1 and 2 moving the screwdriver until there is gap between the cup and the headphones all the around the cup.

Installing the New ear Cups

1. Hold the ear cups tightly with one hand while holding the headphones with the other and gently pull until the cup is completely separated. Note that some headphones may have more adhesive than others so more pressure might be required to remove the ear cup. 
2. Find the replacement ear cup that matches the side removed (they are labeled L and R inside the cup). Align the letter in the cup so that it is legible with the bar at the top.
3. Gently press the ear cup into place ensure that the pins remain aligned.
4. Once there is a slight click sound press more firmly to set the ear cup into place.

Resetting the Partybox to Factory Settings

1. Press and hold "Play" and "Light" buttons for > 10 seconds.
2. The Partybox will power off and back on and is now reset.

Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.

In power ON mode press and hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. 
Now the unit is reset to factory default.
 

With the Flip3 ON, press the Bluetooth briefly to enter pairing mode, while another BT source that is already connected plays on. Now two sources can take turns playing, just by pressing play on one, then the other. The one being overridden will enter pause mode. For complete Bluetooth reset, while the Flip3 is ON and paired, press and hold the Bluetooth button for more than 3 seconds. The Bluetooth button light goes out, and the connection is broken. Press the Bluetooth button again for new pairing.

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.

Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now reset