How To

Support Overview / How To

How To

1217 results
  • How do I reset my JBL headphones?
    With the headphones switched ON, press and hold both volume buttons for more than 5 seconds.
    Your headphones are now reset to factory status.
     
  • How do I reset the Charge 4?
    In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.
  • How do I reset the device to factory settings?
    Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.
  • How do I reset the Endurance Series Headphones?

    For all models except Endurance Peak:
    Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
    Note that resetting the Dive will not erase music contained in the MP3 memory.

    Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

    Endurance Run 2 Wireless reset: Disconnect the earbuds from the paired source device and then press and hold the volume(+) & volume(-) buttons simultaneously for 5 seconds. 

  • How do I reset this unit back to factory settings?
    1. Turn the unit ON.
    2. Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
    3. Unit is now reset.
  • How do I reset to factory defaults?
    Press Phone and "volume +" > 2 sec. Power must be on.
  • How do I see that battery is low?
    The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.
  • How do I see that the headphone is fully charged?
    The red light in the charging status LED on the right cup will turn off.
  • How do I see when my JBL E45BT or E55BT is fully charged?
    While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.
  • How do I skip tracks on the Everest 310/710 headphones?
    To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.
  • How do I skip tracks on the Everest 750NC?
    To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.
  • How do I skip tracks on the Synchros E30?
    The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.
< 1 ... 38 39 40 41 42 ... 102 >

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a support agent
Call us now at: (800) 336-4525

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

Chat With Us

Chat With Us

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)

message

Text Us

Text with a support agent via SMS at:
628-333-7807

Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)