How To

Support Overview / How To

How To

1202 results

Sort

Page size

How do I rename my device?

(1) Select the JBL device you want to rename
(2) Navigate to the Support tile and select "Rename My Product."
(3) Press the current name and type in the new name
(4) Press SAVE

Was this helpful? Thank you for your feedback!
How do I reset my Everest or Everest Elite headphone to pair with another Bluetooth source?

With the headphone in OFF state, press and hold the ON/OFF button for about 7 seconds for the Everest, 16 seconds for the Everest ELITE models. (ELITE changes to 7 seconds as well from software 0.5.6). Bluetooth memory is now erased, and new pairings can be made. An ELITE headphone permits pairing with one source device at a time. If you do not want to do a complete reset as described above, you can use the following method. Without reset, ELITE will try to re-pair with the last source when switched ON. If the last source is not detected, maybe because you want to use another source device, switch the ELITE off and on again, and make sure that the last source device you used is no longer switched ON. This way the ELITE will not be able to "see" the old source, and it will search for a new one. Now the ELITE will again search for the last paired source, and since it cannot find it after some seconds, it will switch back to be open for pairing with a new source. The LED will blink red/blue as an indication of this. The Everest BT models permit pairing with two source devices simultaneously. If you have used both source pairings, and want to pair to a third source, please perform the reset as described above (hold the ON/OFF button for about 7 seconds with the Everest OFF). Now you can again pair two source devices.

Was this helpful? Thank you for your feedback!
How do I reset my JBL Everest 310, 710 and 750 Elite headphones?

With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.

Was this helpful? Thank you for your feedback!
How do I reset my JBL headphones?

With the headphones switched ON, press and hold both volume buttons for more than 5 seconds.
Your headphones are now reset to factory status.

Was this helpful? Thank you for your feedback!
How do I reset the Charge 4?

In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.

Was this helpful? Thank you for your feedback!
How do I reset the device to factory settings?

Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.

Was this helpful? Thank you for your feedback!
How do I reset the Endurance Series Headphones?

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

Endurance Run 2 Wireless reset: Disconnect the earbuds from the paired source device and then press and hold the volume(+) & volume(-) buttons simultaneously for 5 seconds.

Was this helpful? Thank you for your feedback!
How do I reset this unit back to factory settings?
1. Turn the unit ON.
2. Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
3. Unit is now reset.
Was this helpful? Thank you for your feedback!
How do I reset to factory defaults?

Press Phone and "volume +" > 2 sec. Power must be on.

Was this helpful? Thank you for your feedback!
How do I see that battery is low?

The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.

Was this helpful? Thank you for your feedback!
How do I see that the headphone is fully charged?

The red light in the charging status LED on the right cup will turn off.

Was this helpful? Thank you for your feedback!
How do I see when my JBL E45BT or E55BT is fully charged?

While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Everest 310/710 headphones?

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Everest 750NC?

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Synchros E30?

The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the T205?

Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.

Was this helpful? Thank you for your feedback!
How do I switch the enhancer sizes?

The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.

Was this helpful? Thank you for your feedback!
How do I turn off my E45BT or E55BT?

The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.

Was this helpful? Thank you for your feedback!
How do I turn off my internal TV speakers?

Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.

Was this helpful? Thank you for your feedback!
How do I turn off my internal TV speakers?

Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.

Was this helpful? Thank you for your feedback!
How do I turn off the device?

Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.

Was this helpful? Thank you for your feedback!
How do I turn off the Google Assistant on the JBL Everest 310GA and 710GA?

It is not possible to turn the Google Assistant feature off on the headphones, but if you turn off GA on your phone, the headphones won't trigger. On the Everest GA models, the Google Assistant feature is in fact than an extension of your phone, so once you connect to your phone via BT, when you touch the right ear pod, it commands your phone to open the "Hey Google" command.
The only way to stop that from happening is to change the Google settings on your phone to deactivate Google Voice Match, or deactivate Google Assistant entirely.

Was this helpful? Thank you for your feedback!
How do I turn off the Reflect Mini BT?

Press and hold the center power button that is located on the inline microphone. You will see the flashing LED blue light turn off on top of the volume increase button on the microphone.

Was this helpful? Thank you for your feedback!
How do I turn on and pair the UA headphones with my device?

To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the UA WIRELESS headphone. Once you select that option, the audible voice should state, “connected”.

Was this helpful? Thank you for your feedback!
How do I turn on pairing mode?
To activate Bluetooth pairing mode, please follow these steps:
- Press the Bluetooth button on the bottom of the right headphone.
Now find the Headphone in your Bluetooth device settings and select it to connect.
Was this helpful? Thank you for your feedback!
How do I turn SoundShift On?
1. First pair your phone to the Boost TV. You can test this by streaming music to the product.
2. Then press the TV button to switch to the TV sound. Press the TV button again so the LED light is blue--Blue LED means that SoundShift is ON.
3. When you press PLAY on your phone, then you will hear your Bluetooth audio break in over the TV sound. This confirms that SoundShift is working.
4. Simply press SoundShift button again, this will now turn OFF the SoundShift. Now you can watch TV without any interruption from Bluetooth devices.
Was this helpful? Thank you for your feedback!
How do I use Amazon Alexa with my headphones?

- Single tap the left ear cup to engage Alexa.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices and select ‘Use Alexa’.

Was this helpful? Thank you for your feedback!
How do I use my UA Headphones with Record?

Connect your headphones and start a workout using UA Record's heart rate zone tracking. Track your current heart rate zone so you know when to rest or power up, while also viewing your total heart rate distribution throughout each training session. Know your current, average, and peak heart rate. You also have the option to hear your stats read aloud during a workout. With UA Record, you can customize what feedback you hear by setting your stats, frequency, voice, and volume.

Was this helpful? Thank you for your feedback!
How do I use the Google Assistant with my headphones?

- For more information on what your Google Assistant can do, visit: assistant.google.com/platforms/headphones

Was this helpful? Thank you for your feedback!
How do I use the ShareMe option on my Headphones?

The ShareMe button is marked with an S in a circle, and must be clicked briefly. Do not keep the button pressed. Step 4 may go wrong if not done correctly. Please make sure that you have the second Everest 300 turned off. Now press AND HOLD the on/off button for about 15 seconds. The LED must switch to white/red blinking to indicate that it is actually in BT pairing mode. Now simply wait until the two headphones have communicated with each other, and established the BT connection. The white led below the S buttons will light constantly on both headphones when the ShareMe connection is ready. Now you just begin music play on the source, and both headphones will play.

Was this helpful? Thank you for your feedback!
How do I use the unit as a microphone/speaker?

Make sure your device is paired with a mobile device. When receiving a call, press the phone button to answer the call. You can now use it as a speakerphone.

Was this helpful? Thank you for your feedback!
How do simultaneous voice assistants work?

JBL Authentics speakers have both Alexa and Google Assistant no them. This means you don’t need to choose one or the other - you can set up both if you prefer. Then, depending on which voice assistant you’re talking to, the speaker will respond accordingly. It’s like having 2 smart speakers in 1. You can even set a timer with Google Assistant and when it rings ask Alexa to stop it.

Was this helpful? Thank you for your feedback!
How do the neckband flex zones work?

You can bend the ‘arms’ of the neck in and out to get the optimum fit for your exercise/level of activity. The flex zone is the black rubber part on the neckband.

Was this helpful? Thank you for your feedback!
How do the Soundgear Sense earbuds work?

The Soundgear Sense earbuds use JBL OpenSound Technology to deliver rich, full-range sound, while minimizing what others nearby can hear. The earbuds sit outside the ear canal, resting securely on the natural curve of the ear and the precision-placed acoustic ports channel sound directly into the ears. The ear canal remains from any blockage, and this allows the user to still hear ambient sounds while listening to music or taking calls.

Was this helpful? Thank you for your feedback!
How Do You Change the Enhancers (rubber tips)?

There are 5 sizes of fit enhancers that come with the UA Sport Wireless: (4,5,6,7 & 8). Size 7 on the earbuds and (4,5,6 & 8) labeled on the black poly bags. There are three sizes of ear tips that come with the UA Sport Wireless: small, medium & large. Size medium on the earbuds. Size small and large in the black poly bag. The first time you change the enhancers the material might feel a little stiff. Please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. To change sizes, remove both the pre-installed ear tip and fit enhancer, starting with the ear tip. When removing the parts, always grab from the base and be careful not to rip the rubber material. Based on your initial experience, identify which size combination may be a better fit. Each size should be clearly labeled in an individual baggy inside your original packaging or you can find the size of the fit enhancers on the inside with a raised stamp marked with either ‘R’ for Right or ‘L’ for Left along with the numbered size. Most people use the same size for Right and Left but it is possible to use different sizes because some ears are not symmetrical. First, align the sound tunnel of the headphone with the hole in the fit enhancer and gently pull the outer edge of the adapter over the edge of the speaker. Next, align the inner grooves of the ear tip with the grooves in the sound tunnel and gently push the ear tip into position. Try a variety of combinations between the enhancers and ear tips to find the best combination, providing comfort, superior sound quality and secure fit. If you’re still having trouble finding the best fit, please contact customer service at jbl.com/contactus

Was this helpful? Thank you for your feedback!
How do you charge it?

You charge the headphones by plug the USB charging cord into the micro USB port underneath the right side of the neck band. Plug the other end of the charging cord into a USB port.

Was this helpful? Thank you for your feedback!
How do you charge the Everest 110?

To charge the Everest 110, slide the rubber window from the top down to expose the USB charging port that is located on the back of the inline microphone. Please use the JBL charging cable that was included in the packaging to charge these headphones.

Was this helpful? Thank you for your feedback!
How do you lock the device?

Tap and hold the left earpiece for 4 seconds.

Was this helpful? Thank you for your feedback!
How do you power on and pair the Clip 3?
1. Press the power button located on the top right of the speaker.
2. If this is your first time pairing the device, the speaker will automatically go into pairing mode.
3. Make sure that the product you are attempting to pair to is in search mode and in bluetooth range
.
- The Clip 3 should pop up on discoverable devices within a few seconds.
- Choose the Clip 3 option and you will be connected within a few seconds.
Was this helpful? Thank you for your feedback!
How do you power on and pair the E25BT Headphones?

Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The E25BT headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.

Was this helpful? Thank you for your feedback!
How do you power on and pair the JBL Duet Mini BT headphones?

Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The DUET MINI headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.

Was this helpful? Thank you for your feedback!
How do you power on and pair the JBL Reflect Fit headphones?

Press and hold the power button which is located on the right arm of the neck band. Press and hold for 3-5 seconds until you hear the audible voice state "Powering ON" followed by "Looking for device." Make sure the device you are attempting to connect to is in search mode and within bluetooth range. You will see Reflect Fit Audio on the discoverable devices. Choosing this option will allow you to receive audio playback.

Was this helpful? Thank you for your feedback!
How do you power on and pair the Reflect Contour?

Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The Reflect Contour headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.

Was this helpful? Thank you for your feedback!
How do you power on and pair the UA Train headphones?

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.

Was this helpful? Thank you for your feedback!
How do you power on a pair the JR 300BT headphones?

Press the power button located on the bottom of the Right Ear cup. If this is your first time using the headphones, it should immediately start looking for a device to connect to. Make sure that the device that you are trying to connect to is in pairing mode. The JBL JR300BT should display on your discoverable devices within 2-5 seconds. If the headphones have not successfully connected to the device, press and hold the Bluetooth button located next to the Power button on the Right Ear Cup for 2 seconds. As the headphones go into pairing mode, they should connect to your device within 2-5 seconds.

Was this helpful? Thank you for your feedback!
How do you remove the batteries inside the earcup?

The Synchros Chrome is actually the Synchros S500 in chrome-plated version. On the right ear cup, you will find two ridges. These are there to make it possible to remove the disc that covers the batteries. You just position your fingernails against the ridges, to turn the disc counter-clockwise, against a small notch resistance. The Chrome is not painted, but plated. This means that the material is now thicker, and the lid can be rather difficult to remove, because the locking notches are squeezed into position. There is no other way than to put pressure on the ridges, press downward and in a counter-clockwise direction at the same time, and press until the notches, or claws, finally let go, and the lid rotates into open position, when it will fall off. If the lid does not budge, it may be necessary to use some kind of tool, but that can damage the chrome surface. In extreme cases, it may have to go to service.

Was this helpful? Thank you for your feedback!
How do you skip tracks?

The track control button is located in the center of the inline microphone in between the volume control. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward.

Was this helpful? Thank you for your feedback!
How do you skip tracks?

The REFLECT MINI BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do you skip tracks on the Reflect Contour?

The Reflect Contour BT lets you skip the tracks forward, by pressing and holding the volume up button for 3 seconds and skip tracks backward, by pressing and holding the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do you skip tracks on the UA train headphones?

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.

Was this helpful? Thank you for your feedback!
How do you skip tracks on the Under Armour Heart Rate Headphones?

If you want to skip your track forward, simply press and hold the top button on the inline microphone. If you want to skip the track backward, press and hold the bottom button until you hear the track skip backward. You typically hold the button for 1-2 seconds to advance to the next track or to go backwards.

Was this helpful? Thank you for your feedback!
How do you take a phone call with the JBL Free?

Press and hold the RIGHT center button for 1-2 seconds.

Was this helpful? Thank you for your feedback!
How do you track backward?

Tap and hold the left earpiece for 2 seconds

Was this helpful? Thank you for your feedback!
How do you turn on and off the Noise Cancellation feature on the E65BTNC?

The E65BTNC noise cancellation button is located on the bottom Right ear cup. To turn the Active Noise Cancellation on, press and hold the button (Located next to the Bluetooth button) for 2-3 seconds or until you hear the confirmation audio tone. To turn off the noise cancellation, press and hold for 2 seconds or until you hear the audio tone powering off. A white LED next to the button lights up when NC is on.

Was this helpful? Thank you for your feedback!
How do you turn on and off the Noise Cancellation feature on the JBL DUETNC?

The DUET NC noise cancellation button is located on the bottom Right ear cup. To turn the Active Noise Cancellation on, press and hold the button (Located next to the Bluetooth button) for 2-3 seconds or until you hear the confirmation audio tone. To turn off the noise cancellation, press and hold for 2 seconds or until you hear the audio tone powering off. A white LED next to the button lights up when NC is on.

Was this helpful? Thank you for your feedback!
How is it possible to check the software version of a JBL Horizon?

By pressing and holding the Bluetooth and the Volume PLUS buttons at the same time. The software version is shown in the display.

Was this helpful? Thank you for your feedback!
How is the remote control used?

When playing music: one click is Pause or Play. Two clicks skips to next track. Three clicks skips back to start of track or previous track. At all times, hold the button to start voice-activated phone functions. For telephone use: one click to accept a call, two clicks to end the call.

Was this helpful? Thank you for your feedback!
How is the SB150 reset to factory default settings?

Unplug the power cord from soundbar. While holding down the VOLUME + button, plug the power cord into the soundbar. A green LED, followed by a blue LED will light up, after which the soundbar will go into standby. The SB150 is now reset.

Was this helpful? Thank you for your feedback!
How is the software updated first time, and after that?

For headphones with Version 4.0 of the Firmware, the first update will be done via USB cable, and after the first update, all subsequent updates will be delivered over the air. For headsets with version 5.0 of the firmware, all updates will be delivered over the air, via the app

Was this helpful? Thank you for your feedback!
How it works when docked and connected to the harness, when undocked & portable

When docked and connected to the harness, the BASSPRO GO can be used as a powered subwoofer or a full-range car audio speaker. It receives it’s audio source from the head unit via the wiring harness and it’s power from the car battery. Bluetooth is not active.

When undocked/portable and removed from the harness, it can no longer be used as a powered sub. It is strictly a full-range portable Bluetooth speaker system. It receives it’s audio source from the Bluetooth input only, and receives it’s power from the internal battery.

Was this helpful? Thank you for your feedback!