How To
How To
1203 results
-
The UA Sport Wireless Heart Rate must be charged with a micro USB charger that is provided in the packaging. You will find the USB outlet located on the bottom left side of the inline microphone. There will be a small rubberized window that you can slide up and over to expose the outlet. After plugging in the headphones, you will see a solid red light appear at the bottom of the inline microphone. Once the headphones are fully charged, the red light will turn off. It typically takes less than 2 hours of charging time to receive the 5 full hours of audio playback.Was this helpful? Thank you for your feedback!
-
Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.Was this helpful? Thank you for your feedback!
-
The firmware version of the headphone will be displayed in the settings page of the app.Was this helpful? Thank you for your feedback!
-
We recommend cleaning the earphones with audio or electronic wipes.Was this helpful? Thank you for your feedback!
-
You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.Was this helpful? Thank you for your feedback!
-
To clean yurbuds, remove the enhancers (tips) from earphones and wash with warm, soapy water. Do not use anything containing alcohol. Completely dry the enhancers and reposition on the earphones, as shown in the Quick Start guide: Left bud between 3:00 and 4:00 position Right bud between 8:00 and 9:00 positionWas this helpful? Thank you for your feedback!
-
• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.Was this helpful? Thank you for your feedback!
-
• Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.Was this helpful? Thank you for your feedback!
-
To set up and enjoy all the features of your UA Sport Wireless Heart Rate, you’ll need to connect it to your phone using the UA Record™ mobile app. Select the UA Sync icon in the upper right hand corner of the dashboard. Tap on “UA Sport Wireless Heart Rate”. Follow the on-screen instructions to finish setup. Once connected, the headphones will live under My Apps and Devices. Here, you can access your headphones' settings to check your battery level, current heart rate, and help.Was this helpful? Thank you for your feedback!
-
- Visit App store and download ‘Amazon Alexa’ App.
Was this helpful? Thank you for your feedback! -
To pair the JBL LIVE headphones the first time, switch the headphone on, look for the blinking blue light indicating pairing mode. Switch on Bluetooth on your source device, find the JBL LIVE headphones in Settings > Bluetooth and confirm pairing. To pair the JBL LIVE headphones from the second time onwards, or to link them with a different device, press and hold the power button until the blue flashing light is visible.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are completely shut off and proceed to press and hold the power button for 4-6 seconds. You will see the LED indicator light flash red and blue when the headphones are in paring mode. Make sure that Bluetooth is enabled on your listening device and look for “JBL Reflect Response” in the Bluetooth device list. Select “JBL Reflect Response” to connect. After the headphones are connected with a listening divine you will not need to reconnect them, your device should automatically connect to the headphones when both items are on.Was this helpful? Thank you for your feedback!
-
In normal use, T450BT pairing mode is automatic. First time it is switched on, it goes into pairing mode at once, shown by the blue LED blinking. After first pairing, if the last used source is not on when the T450BT is switched on, it will wait about 10 seconds with the LED showing white light, then it will switch to pairing mode, with the LED turning blue, and blinking. If you want to start pairing mode manually, make sure that the headphones are switched off, then press and hold the on/off button for more than 5 seconds. The headphones will now switch on in pairing mode, shown by the blue LED blinking.Was this helpful? Thank you for your feedback!
-
First connect your audio/video sources to your TV inputs. Then connect the provided optical or analog audio output from your TV to the Boost TV.Was this helpful? Thank you for your feedback!
-
To pair a different Bluetooth device, make sure that the unit is turned off. You then must press and hold the center button for about 3-5 seconds. You should see the light blink red and blue while it is in pairing mode and the audible voice should state, “looking for device”. You should see UA BT Wireless pop up on the device that you are attempting to pair it with. Choose that option and wait for the audible voice to state, “connected”Was this helpful? Thank you for your feedback!
-
The Club 5501 is a mono amplifier for subwoofer use in cars. It can be confusing to see that it has two inputs, marked left and right, as well as two speaker output pairs. But it is still a mono amplifier, with only one channel. The two inputs are there to make it easier to connect to a normal car radio/head unit, where you will often have two normal full-range connectors, left and right. You can insert both into the 5501. However, if you only have one signal lead going to the 5501, you can use either of the inputs. They are combined into one inside the amplifier anyway. Also, the two sets of speaker connections are there to make it easier to connect two subwoofers simultaneously. The two sets are completely identical, so you can use either one for a single subwoofer, or both. If you connect two, they will be in parallel.Was this helpful? Thank you for your feedback!
-
The Stadium GTO 20M is intended for use with the Stadium GTO two-way systems, or to replace existing midrange speakers in systems that are already three-way from the start. The Stadium GTO two-way component systems are 3-way upgradeable. The crossovers are gap-switchable to accommodate a midrange upgrade. The optional Stadium GTO 20M midrange includes a bandpass crossover to convert a two-way system into a threeway system with perfect tonal balance. You simply connect both crossovers to the speaker wires from your car amplifier in parallel, and set the existing GTO two-way crossover to GAP function. Stadium GTO 20M is designed to also fit into many factory three-way applications. Please note that you cannot use this add-on midrange with coaxial car speakers, unless you can access the crossover networks to establish the midrange gap that the extra midrange is meant to occupy.Was this helpful? Thank you for your feedback!
-
Make sure that the headphones are turned off. Press hold the power button for 3-5 seconds until you hear the audible voice stating “looking for device” You will see the LED lights flash red and blue as it is searching for a new device to connect to. Make sure the device you are trying to connect to is in search mode and it should recognize the device within a few seconds.Was this helpful? Thank you for your feedback!
-
Press and hold the power button located on the neck band for 3-5 seconds or until you hear the audible voice stating, "powering on.......JBL Everest is ready to pair. Go to the pairing menu on your device" While it is in pairing mode you should see the LED light on the neckband alternate between white and red. The device that you are trying to connect to should recognize the Everest Elite 100 within a few seconds. Once connected, you should see a flashing LED white light on the neckband.Was this helpful? Thank you for your feedback!
-
Unfortunately, the JBL Reflect Response does not feature volume control.Was this helpful? Thank you for your feedback!
-
Simply turn off one of the products.Was this helpful? Thank you for your feedback!
-
Sidetone is off by default.
To enable sidetone on your JBL Quantum Stream microphone, install and start JBL QuantumENGINE, and head to the "Microphone" tab.
Here you can select sidetone level from 0 to 3 (0 = off).
Was this helpful? Thank you for your feedback! -
First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional ear buds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left ear bud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. After the enhancers are securely locked in the ear, we recommend wrapping the ear loop up and over the ear for the most comfortable fit. Please note, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone and your ear. The size 7 will be featured on the model; two smaller sizes (5 & 6) and one larger (8) will be included in the packaging. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size. If you’re unable to find a secure fit, one our fit specialists can assist you with a different size or guidance on how to properly wear these headphones. For any questions or concerns regarding fit and sizing, please contact your local JBL Customer Support or please email us from our Support page at https://www.jbl.com/support-contact.html.Was this helpful? Thank you for your feedback!
-
If you cannot stream music with AirPlay, use the JBL One App;
(1) Go to Settings.
(2) Select 3rd Party Service.
(3) Select the Airplay tile.
(4) Select Reset AirPlay.Was this helpful? Thank you for your feedback! -
This product uses a standard micro usb cable, which can be purchased from most any retailer.Was this helpful? Thank you for your feedback!
-
First, it is very important that you use the correct size enhancers (rubber tips). While the tips may appear too large, these do not go all the way into your ear canal. The enhancers are supposed to fill the entire bowl (concha) of your ear, so please be sure to try both sizes to ensure a comfortable fit. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. Next, gently insert the enhancer into your ear with a forward motion towards the jaw, twist and lock into place. If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email us from our Support Page at https://www.jbl.com/support-contact.html to request yours today.Was this helpful? Thank you for your feedback!
-
First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional earbuds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. These headphones come with 5 sizes of fit enhancers (4, 5, 6, 7 & 8) and 3 sizes of ear tips (small, medium & large). The fit enhancers sit in the bowl of your ear and are essential for a secure fit, while the ear tips are inserted in the inside of the ear canal and provide sound occlusion. The size 7 fit enhancer and large ear tip comes pre-installed on the headphone. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size.Was this helpful? Thank you for your feedback!
-
For the best performance, connect the speaker to a power outlet.
Was this helpful? Thank you for your feedback! -
After the wake-up process is finished, and the radio alarm has been turned off by pressing the alarm button, it is necessary to press the radio button to keep the radio playing.Was this helpful? Thank you for your feedback!
-
As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)