How To
How To
1202 results
-
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.Was this helpful? Thank you for your feedback! -
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The red charge light turns off when charging has finished.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SHORT press the multi-function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
Onboard Adaptive Noise Cancellation is controlled by the multi-function button on the rear of the left ear-cup. The feature is switched on by default, but you can SHORT press the multi function button to toggle from ANC to talk-through. Turn off ANC by long-pressing the multi-function button.Was this helpful? Thank you for your feedback!
-
When the earbuds are connected to the USB wireless dongle and Bluetooth connection at the same time, triple tab on the left earbud to switch between the two connections. You'll hear a tone after you triple tab the left earbud signaling the switching is in progress. If you receive an incoming call from your mobile device, you can double tap either earbud and the earbuds will automatically switch over to that connection while answering the call.Was this helpful? Thank you for your feedback!
-
All updates will happen over-the-air, meaning that your device just needs to be connected via your Wi-Fi network with at least 30% battery and plugged into the charger, then it will update during the night if there are any new updates available.Was this helpful? Thank you for your feedback!
-
By using Google Home app, and if a software is available then the app will notify you about the newest software available. Google Home app can be downloaded from Apple Play Store or Google Play Store.Was this helpful? Thank you for your feedback!
-
If your JBL Link 10 or Link 20 is out of range, setting up a personal hotspot from your mobile device will allow your Google Assistant to answer again. However, this process requires two mobile smartphones, one as the "mobile hotspot" and the second to connect the JBL Link 10 or Link 20 to your network.Was this helpful? Thank you for your feedback!
-
Switch the headphone ON, then press both volume buttons (VOL + and VOL-) at the same time, and hold them for 5-6 seconds. The headphones are now reset to factory default.Was this helpful? Thank you for your feedback!
-
The JBL Quantum TWS works on most mobile devices, however, some mobile devices restrict the utilization of it's audio and microphone functions via USB-C causing there to be no audio or microphone operation. In these cases we recommend connecting to the earbuds using their Bluetooth connection.Was this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
Let's say you have 4 LINK devices in your home and you start your day with "OK Google, How is the weather?".
All of your devices will "light up" and start listening to the command. However, only one of the speakers will give you the information (if they are under the same account).
The speaker with the best microphone reception will respond with an answer.
Please note: if you have muted all speakers or 3 out of 4 are muted, then only one will respond and the rest will not react.
If all speakers are muted, all will be silent.Was this helpful? Thank you for your feedback! -
For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.Was this helpful? Thank you for your feedback!
-
BT sources are volume controlled by the Primary Volume control. BT volume relative to other sources must be adjusted either on the BT source or on the mixer’s input volume controls. Bluetooth does not occupy any of the other inputs.Was this helpful? Thank you for your feedback!
-
Press the microphone button (located on the LEFT arm) to turn on the first RunSafe mode. The first mode blinks continually. When you press the microphone again, the second mode is initiated which features 2 blinks on followed by 2 seconds without. Pressing the microphone again is the third mode which is 3 blinks on followed by 3 seconds without.Was this helpful? Thank you for your feedback!
-
In our Quick Start Guide, there is a section under "One Touch Play Feature", where we explain how it works. We advise to take a look at it.Was this helpful? Thank you for your feedback!
-
After pressing the Play button, you must wait 3 seconds before you can press the Play button again when listening to videos over AirPlay.
Was this helpful? Thank you for your feedback! -
If you want to pair and connect to a different device, make sure the headphones are turned off. Proceed to turn the headphones on by pressing and holding the power button for 3- 5 seconds until you hear the audible voice stating “power on” followed by “looking for device.” You will see the LED alternate between blue and red as it searches for your new device. Make sure your device is in search mode. Within seconds your headphone should appear as one of your discoverable devices. You will then hear the audible voice stating, “audio connected” followed by a blinking blue LED light located on the inline microphone indicating that it is now connected to a device.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are turned on and connected to your smart device. Press and hold the Microphone button located on the LEFT arm of the neckband. You should be able to activate Siri/Google within 3 seconds after pressing the Microphone button.Was this helpful? Thank you for your feedback!
-
1) Download and run the latest JBL Connect app on your phone 2) The JBL Connect app will begin discovering your JBL Boombox (please make sure your speaker is connected via Bluetooth first) 3) Use the toggle switch in the JBL Connect App to change the phone button to now have the voice assistant function 4) Simply press the “Play” button on your JBL Boombox (you will hear a brief tone) and begin speaking your commands via SIRI and Google Now. 5) Please check the below links for more information regarding SIRI and Google Now available voice commands: SIRI: https://support.apple.com/HT204389 Google Now: https://support.google.com/websearch/answer/2940021Was this helpful? Thank you for your feedback!
-
Tap and hold the right earpiece for 4 seconds.Was this helpful? Thank you for your feedback!
-
To increase the volume, quickly press the top button located on the inline microphone with several quick clicks. If you want to decrease the volume, quickly press the bottom button with several quick clicks until desired volume is achieved.Was this helpful? Thank you for your feedback!
-
To answer and hang up calls, press the pause/play button located on the left arm of the Soundgear.Was this helpful? Thank you for your feedback!
-
To remove the enhancer, pinch the edge opposite of the sound tunnel between your thumb and forefinger and firmly pull up and off the ear bud. Replacement enhancers are specific to the left and right ear bud. An (L) or (R) and size indicator is located on the inside of the enhancer. When changing the enhancers, you must place the right enhancer on the right ear bud and the left enhancer on the left ear bud. Firmly grasp the earbud with one hand and align the sound tunnel of the enhancer with your other hand and stretch the enhancer up and over the top of the red earbud. Check the alignment of the sound tunnel to insure best sound performance. If sound is muffled or weak, check and rotate sound tunnel. Most people use the same size for Right and Left but it is possible to use different sizes because some ears are not symmetrical. - If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email ua.jblsupport@harman.com to request yours today.Was this helpful? Thank you for your feedback!
-
The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.Was this helpful? Thank you for your feedback!
-
The UA Sport Wireless Heart Rate must be charged with a micro USB charger that is provided in the packaging. You will find the USB outlet located on the bottom left side of the inline microphone. There will be a small rubberized window that you can slide up and over to expose the outlet. After plugging in the headphones, you will see a solid red light appear at the bottom of the inline microphone. Once the headphones are fully charged, the red light will turn off. It typically takes less than 2 hours of charging time to receive the 5 full hours of audio playback.Was this helpful? Thank you for your feedback!
-
Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.Was this helpful? Thank you for your feedback!
-
The firmware version of the headphone will be displayed in the settings page of the app.Was this helpful? Thank you for your feedback!
-
We recommend cleaning the earphones with audio or electronic wipes.Was this helpful? Thank you for your feedback!
-
You can clean it by wiping it gently with a damp cloth. Take extra care not to let water leak into the speaker chamber, as it will damage the speaker drivers.Was this helpful? Thank you for your feedback!
-
To clean yurbuds, remove the enhancers (tips) from earphones and wash with warm, soapy water. Do not use anything containing alcohol. Completely dry the enhancers and reposition on the earphones, as shown in the Quick Start guide: Left bud between 3:00 and 4:00 position Right bud between 8:00 and 9:00 positionWas this helpful? Thank you for your feedback!
-
• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.Was this helpful? Thank you for your feedback!
-
• Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.Was this helpful? Thank you for your feedback!
-
To set up and enjoy all the features of your UA Sport Wireless Heart Rate, you’ll need to connect it to your phone using the UA Record™ mobile app. Select the UA Sync icon in the upper right hand corner of the dashboard. Tap on “UA Sport Wireless Heart Rate”. Follow the on-screen instructions to finish setup. Once connected, the headphones will live under My Apps and Devices. Here, you can access your headphones' settings to check your battery level, current heart rate, and help.Was this helpful? Thank you for your feedback!
-
- Visit App store and download ‘Amazon Alexa’ App.
Was this helpful? Thank you for your feedback! -
To pair the JBL LIVE headphones the first time, switch the headphone on, look for the blinking blue light indicating pairing mode. Switch on Bluetooth on your source device, find the JBL LIVE headphones in Settings > Bluetooth and confirm pairing. To pair the JBL LIVE headphones from the second time onwards, or to link them with a different device, press and hold the power button until the blue flashing light is visible.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are completely shut off and proceed to press and hold the power button for 4-6 seconds. You will see the LED indicator light flash red and blue when the headphones are in paring mode. Make sure that Bluetooth is enabled on your listening device and look for “JBL Reflect Response” in the Bluetooth device list. Select “JBL Reflect Response” to connect. After the headphones are connected with a listening divine you will not need to reconnect them, your device should automatically connect to the headphones when both items are on.Was this helpful? Thank you for your feedback!
-
In normal use, T450BT pairing mode is automatic. First time it is switched on, it goes into pairing mode at once, shown by the blue LED blinking. After first pairing, if the last used source is not on when the T450BT is switched on, it will wait about 10 seconds with the LED showing white light, then it will switch to pairing mode, with the LED turning blue, and blinking. If you want to start pairing mode manually, make sure that the headphones are switched off, then press and hold the on/off button for more than 5 seconds. The headphones will now switch on in pairing mode, shown by the blue LED blinking.Was this helpful? Thank you for your feedback!
-
First connect your audio/video sources to your TV inputs. Then connect the provided optical or analog audio output from your TV to the Boost TV.Was this helpful? Thank you for your feedback!
-
To pair a different Bluetooth device, make sure that the unit is turned off. You then must press and hold the center button for about 3-5 seconds. You should see the light blink red and blue while it is in pairing mode and the audible voice should state, “looking for device”. You should see UA BT Wireless pop up on the device that you are attempting to pair it with. Choose that option and wait for the audible voice to state, “connected”Was this helpful? Thank you for your feedback!
-
The Club 5501 is a mono amplifier for subwoofer use in cars. It can be confusing to see that it has two inputs, marked left and right, as well as two speaker output pairs. But it is still a mono amplifier, with only one channel. The two inputs are there to make it easier to connect to a normal car radio/head unit, where you will often have two normal full-range connectors, left and right. You can insert both into the 5501. However, if you only have one signal lead going to the 5501, you can use either of the inputs. They are combined into one inside the amplifier anyway. Also, the two sets of speaker connections are there to make it easier to connect two subwoofers simultaneously. The two sets are completely identical, so you can use either one for a single subwoofer, or both. If you connect two, they will be in parallel.Was this helpful? Thank you for your feedback!
-
The Stadium GTO 20M is intended for use with the Stadium GTO two-way systems, or to replace existing midrange speakers in systems that are already three-way from the start. The Stadium GTO two-way component systems are 3-way upgradeable. The crossovers are gap-switchable to accommodate a midrange upgrade. The optional Stadium GTO 20M midrange includes a bandpass crossover to convert a two-way system into a threeway system with perfect tonal balance. You simply connect both crossovers to the speaker wires from your car amplifier in parallel, and set the existing GTO two-way crossover to GAP function. Stadium GTO 20M is designed to also fit into many factory three-way applications. Please note that you cannot use this add-on midrange with coaxial car speakers, unless you can access the crossover networks to establish the midrange gap that the extra midrange is meant to occupy.Was this helpful? Thank you for your feedback!
-
Make sure that the headphones are turned off. Press hold the power button for 3-5 seconds until you hear the audible voice stating “looking for device” You will see the LED lights flash red and blue as it is searching for a new device to connect to. Make sure the device you are trying to connect to is in search mode and it should recognize the device within a few seconds.Was this helpful? Thank you for your feedback!
-
Press and hold the power button located on the neck band for 3-5 seconds or until you hear the audible voice stating, "powering on.......JBL Everest is ready to pair. Go to the pairing menu on your device" While it is in pairing mode you should see the LED light on the neckband alternate between white and red. The device that you are trying to connect to should recognize the Everest Elite 100 within a few seconds. Once connected, you should see a flashing LED white light on the neckband.Was this helpful? Thank you for your feedback!
-
Unfortunately, the JBL Reflect Response does not feature volume control.Was this helpful? Thank you for your feedback!
-
Simply turn off one of the products.Was this helpful? Thank you for your feedback!
-
Sidetone is off by default.
To enable sidetone on your JBL Quantum Stream microphone, install and start JBL QuantumENGINE, and head to the "Microphone" tab.
Here you can select sidetone level from 0 to 3 (0 = off).
Was this helpful? Thank you for your feedback! -
First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional ear buds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left ear bud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. After the enhancers are securely locked in the ear, we recommend wrapping the ear loop up and over the ear for the most comfortable fit. Please note, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone and your ear. The size 7 will be featured on the model; two smaller sizes (5 & 6) and one larger (8) will be included in the packaging. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size. If you’re unable to find a secure fit, one our fit specialists can assist you with a different size or guidance on how to properly wear these headphones. For any questions or concerns regarding fit and sizing, please contact your local JBL Customer Support or please email us from our Support page at https://www.jbl.com/support-contact.html.Was this helpful? Thank you for your feedback!
-
If you cannot stream music with AirPlay, use the JBL One App;
(1) Go to Settings.
(2) Select 3rd Party Service.
(3) Select the Airplay tile.
(4) Select Reset AirPlay.Was this helpful? Thank you for your feedback! -
This product uses a standard micro usb cable, which can be purchased from most any retailer.Was this helpful? Thank you for your feedback!
-
First, it is very important that you use the correct size enhancers (rubber tips). While the tips may appear too large, these do not go all the way into your ear canal. The enhancers are supposed to fill the entire bowl (concha) of your ear, so please be sure to try both sizes to ensure a comfortable fit. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. Next, gently insert the enhancer into your ear with a forward motion towards the jaw, twist and lock into place. If you’re unable to find a secure fit with both sizes in the box, we can send you a complimentary sizing pack with two additional sizes. Please email us from our Support Page at https://www.jbl.com/support-contact.html to request yours today.Was this helpful? Thank you for your feedback!
-
First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional earbuds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. These headphones come with 5 sizes of fit enhancers (4, 5, 6, 7 & 8) and 3 sizes of ear tips (small, medium & large). The fit enhancers sit in the bowl of your ear and are essential for a secure fit, while the ear tips are inserted in the inside of the ear canal and provide sound occlusion. The size 7 fit enhancer and large ear tip comes pre-installed on the headphone. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size.Was this helpful? Thank you for your feedback!
-
For the best performance, connect the speaker to a power outlet.
Was this helpful? Thank you for your feedback! -
After the wake-up process is finished, and the radio alarm has been turned off by pressing the alarm button, it is necessary to press the radio button to keep the radio playing.Was this helpful? Thank you for your feedback!
-
As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.Was this helpful? Thank you for your feedback!
-
You will hear an audio prompt to readjust the position of the left ear piece stating “heart rate not detected, adjust ear bud position”. The sensor is also in the correct position when the green LED light is not visible from the outside of your ear.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)