How To
How To
1217 results
-
EON 208P:
Two of the inputs are made for stereo use:
CH 5/6 with volume control and ¼” phone plugs or RCA plugs, and
CH 7/8 with volume control and ¼” phone plugs or 3.5 mm stereo input.Also, the Bluetooth wireless input is stereo.
EON ONE:Two of the inputs are made for stereo use:CH 3/4 with volume control and ¼” phone plugs or RCA plugs, and
CH 5/6 without volume control and 3.5 mm input jack
Also, the Bluetooth wireless input is stereo.Was this helpful? Thank you for your feedback! -
Place the USB wireless dongle in the USB-C connector of your device and place the earbuds in your ears. The earbuds will automatically connect to your USB wireless dongle. If the earbuds don't pair automatically you can manually pair them again by connecting the JBL Quantum TWS to a mobile device via Bluetooth and open the JBL Headphones app. Turn on the "Dongle Pairing" mode and then press the pairing button on the USB wireless dongle. (Note: USB wireless dongle needs to be connected to an activated device). You will get a message on your JBL Headphones app that the pairing is successful and then press "Understood".Was this helpful? Thank you for your feedback!
-
Please press JBL Connect buttons on both speakers to connect.Was this helpful? Thank you for your feedback!
-
This headphone does not have volume control. It features a one button in-line remote that enables you to pause/play, skip tracks and answer/hang up phone calls. The microphone that is built into the remote permits use as headset with a mobile phone.Was this helpful? Thank you for your feedback!
-
To get the full potential of the HDMI content/source you have in your home, then you need to enable HDMI UHD deep color option on your TV for the HDMI output port (ARC).
Since there are tons of different TVs and manufactures out there, the best way to see if your TV can use 10-bit color on HDMI, is to read the TV's manual or call their support section.Was this helpful? Thank you for your feedback! -
Once the speaker/soundbar is connected to the network, software updates will automatically be sent to the speaker/soundbar through Wi-Fi or the internet, if availableWas this helpful? Thank you for your feedback!
-
In the JBL ONE App:
(1) Go to My Products, select your product
(2) Select Support tile
(3) Under General, select Product SupportWas this helpful? Thank you for your feedback! -
After setting up one or both voice assistants on your JBL Authentics speaker, you must make sure that you have connected your supported music service account to your Amazon and/or Google account in the Alexa and Google Home apps.
For Alexa, if you then set one of the music services as default in the Alexa app settings, you can play music from this service just by asking Alexa to play music.
Was this helpful? Thank you for your feedback! -
Unfortunately, the JBL AmpUp App is no longer available for download.Was this helpful? Thank you for your feedback!
-
If you are not using the microphone, make sure that any communication software such as Zoom, Skype, Discord, etc. are closed and that your microphone is muted. You can also take advantage of it's Dual Connect feature and place one of the earbuds in the charging case and speed charge the earbuds to extend the playback time.Was this helpful? Thank you for your feedback!
-
On the back of the SB150 subwoofer, you will find a "pair" button. Hold down the pair button for 3 seconds. It will start flashing amber rapidly, indicating that the pairing mode has begun. You don't need to press other buttons to make a connection, once the amber light is steady, it is connected to your SB150 soundbar.Was this helpful? Thank you for your feedback!
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.Was this helpful? Thank you for your feedback!
-
You can reach out to the Under Armour Customer Service in the USA by phone at 1.800.377.9952 or by e-mail at ua.jblsupport@harman.com.Was this helpful? Thank you for your feedback!
-
On the soundbar, press and hold the power and source button for more than
10 seconds.
Please note this procedure will revert ALL settings back to factory default.Was this helpful? Thank you for your feedback! -
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.Was this helpful? Thank you for your feedback!
-
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.Was this helpful? Thank you for your feedback! -
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
The charging LED stops lighting white, and goes dark.Was this helpful? Thank you for your feedback!
-
When the Xtreme is ON, the row of 5 diodes at the bottom of the front will light up in turn, with the top flashing LED showing how far charging has progressed. When full charge has been reached, all diodes light constantly. In some cases, the fifth diode keeps on blinking, but does not light up constantly, no matter how long charging continues. Sometimes it will show constant light after charging has been stopped. This is normal, caused by tolerances in the circuits, and is no cause for alarm. The battery is charged to the same level. If the Xtreme is OFF, no diodes will light when full charge has been reached.Was this helpful? Thank you for your feedback!
-
The red charge light turns off when charging has finished.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)