Yes, steam and drops of water in a bathroom are fine.

Yes, steam and drops of water in a bathroom are fine.

Yes, you can use them for telephone conversations in both Bluetooth and wired mode when paired with a smart device. 

Yes, you can play game either wired or wirelessly while using USB-C charging cable.  

Yes. Out-the-box the JBL Bar series soundbar recognizes volume and mute controls from the most common TV remote controls. The JBL Bar series has IR learning. You can use this feature to teach the soundbar to response to your TV's remote control as well.

Yes, use the MONITOR OUT sockets (1/4” and RCA are available on 208P, RCA on ONE) to feed into a recording device. Please note that these outputs are volume controlled, so set the volume correctly, depending on the sensitivity of the recording device.

It is possible to replace the ear pads, but there are details to consider. On Elite 700: The ear pads are held in place by a plastic plate with claws, and some of the claws will most likely break off when you remove the pad. You do this by grabbing under the edge where the fabric ends, then pulling hard outward. The claws will eventually let go, and some of them will break off, rattling inside the ear pod. The only way to get them out is to unscrew the speaker plate, lift it up, and shake out the broken-off claws. The new pads are simply centered over the speaker plate, and the claws pressed into the holes with a firm pressure. On Everest 700: The ear pads are glued into position with double-adhesive tape. Pull the old pads off with a forceful, steady pull, until the glue lets go. Remove the protective layer on the new pads, and carefully position them correctly before pressing home all the way around the edge.

Yes, the ear pads are replaceable by owner. The pads can be purchased as spare parts from the service center, or purchased directly from the JBL spare parts web shop, when opened.

No, the pads are glued to the headphone body, and must be replaced by a service technician.

Yes, on the master speaker (the one with playback buttons), simply press the Reverse and Forward Play buttons at the same time for 3 seconds. Please note that after you have performed the reset procedure, master and secondary speakers are no longer connected. Go to the owner's manual page 4, the section "speaker association", to pair the secondary and master again.

Yes it is possible to reset your speaker. The reset will remove all Bluetooth pairings and WiFi network settings. In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash. Your JBL Authentics L8 or L16, are now back to factory settings. Please reconnect the speaker to your WiFi network again.

You can only share the sound via JBL Connect through Bluetooth connected devices. TV sound is not permitted as it would cause lip-sync issues.

Yes, the E45BT headphones also have an detachable audio cable that you can plug into the headphones. The plug is located at the bottom of the right ear cup.

Yes, Control Xstream is a Chromecast device that allows you to cast music content via your Chrome browser. However, the JBL Control Xstream is not made for video purposes, because there will be delay between sound and image.

Yes. The Google cast function works independent to that of Bluetooth, therefore you are able to Bluetooth connect to another device while casting audio to the JBL Playlist simultaneously. This feature is applicable on smartphones, tablets/iPad, and Bluetooth capable computers.

You should not submerge the speaker into any water or liquid.

No. These headphones are not waterproof. Swimming with these headphones will cause significant and irreversible damage.

Yes, although this is not mentioned in the owner's manual, it can be done by pressing and holding the light effect button for more than two seconds.

Yes, the E25BT features a three button microphone which enables you to pause/play, skip tracks and answer and hang up phone calls.

Yes, the JBL Duet Mini features a three button microphone which enables you to pause/play, skip tracks and answer and hang up phone calls.

Yes, the E45BT headphones allow you to switch seamlessly from your music on your portable device to your phone. The controls are located on the Right ear cup which features your volume control and pause and play which is located in the center of the controls. The center button will allow you to answer and hang up phone calls .

Yes. A usb wall adapter would be required.

You can turn the Heart Rate sensor off and still use the headphones for audio by placing your finger on the right earpiece for 3-4 seconds. You will hear an audio prompt stating, “Heart Rate disconnected” which will turn the Heart Rate sensor off. If you wish to turn the sensor back on, simply place your finger on the RIGHT earpiece again for 3-4 seconds until you hear the voice prompt stating that the Heart Rate sensor has been turned back on.

Yes, from within the JBL Connect App, when you have 2 JBL Boombox speakers connected, set them in Stereo Mode. When you add a 3rd ( or more ) JBL Boombox speakers, they will automatically revert back to Party mode

Yes, just be aware that you are responsible for correct installation when using 3rd party wall mounts. The included wall-mounting kit in the box fits perfectly and is good for outdoor or indoor use.

No, in-ceiling speakers cannot be used in the wall due to speaker dimensions. A wall is not deep enough to accommodate the depth of an in-ceiling speaker. For in-wall speakers, you can install them in the ceilings without any depth issues. However, for quality listening, we recommend using architectural speakers according to their intended purpose.

Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Playlist also offers a Bluetooth connection and an AUX input

Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Control Xstream also offers a Bluetooth connection and an AUX input

Yes, both voice assistants are supported by the JBL LIVE headphones.
Amazon Alexa or Google Assistant must be selected as the default voice assistant through the My JBL Headphones app.
The two voice assistants cannot be used simultaneously. You can always change your default voice assistant through the My JBL Headphones app.

The EVEREST models 100, 300 and 700 are all updated with the HID (Human Interface Device) tool, available in the download section for each model. This tool works with Windows computers only. The EVEREST ELITE models are updated with a USB tool available on the special Everest web page. This tool is available in both an Apple MAC OS version and a Windows version. This USB tool update is used for the first production run of ELITE models ONLY, and only once! All later production runs, and all updates after this first USB update, will take place wirelessly through the My JBL Headphone app, made for iOS and Android.

Yes, you do not need to have music playing to keep the noise cancelling switched on. There may be a slight residual hiss from the NC system, which would usually be masked by music, but there will still be a significant reduction of external noise.

Yes, this is no problem.

Yes, you can activate the noise reduction circuits alone, with no connection to a source device by Bluetooth or cable. The headphones will stay on as long as there is power in the battery, which is close to 30 hours for pure NC function. Please note that there is a slight residual noise from the NC system, which will be drowned out by music playing, or by surrounding noise such as airplane noise. If you use the NC in surroundings that are near quiet to begin with, you may not get an improvement in noise level.

Yes, this is no problem.

Yes, no problem.

Yes, press and hold the remote button with the round dot (between volume up and volume down) for for about three seconds. Your iPhone will confirm with a tone that SIRI is ready for voice input.

Yes, the Arena Sub 100P can be used in multiple regions. The subwoofer’s power requirement ranges from 100 volts – 240 volts, 50/60 hertz. As long as you have an adapter to properly plug the speaker into various wall outlets, the Arena Sub 100P will work anywhere in the world.

Only Bluetooth pairing can be used for JBL Connect on Boost TV.

No. The only way that the Noise Cancellation feature can be activated is while you are using the headphones wirelessly. You cannot use NC while the headphones are plugged into a device or charging.

The Game-Chat balance dial only works when your headset is powered on. Please note that it supports connection with a USB Type A to C cable and a wireless transmitter dongle, but doesn’t support connection through a 3.5mm cable or Bluetooth for mobile games.

The Game-Chat balance dial only works when your headset is powered on. Please note that it supports connection with a USB Type A to C cable and a wireless transmitter dongle, but doesn’t support connection through a 3.5mm cable or Bluetooth for mobile games.
The Game-Chat balance dial is compatible with PC and Mac, but not with PS4 I 5, Xbox Series X | S, Nintendo Switch or Mobile.

The JBL Quantum 800 can only be used via a 3.5mm, Bluetooth, or 2.4Ghz wireless connection.

Unfortunately, the OR100 are specifically designed for the Oculus Rift only. You cannot use these headphones on other devices.

No, the OR 300 headphones are specifically made for the Oculus Rift. These headphones will not work with any other device.

Yes, all sources that output analog stereo line-level signals or stereo audio optical digital signals may be used, cable-connected to the BTA 20 transmitter. Digital signals must be in PCM format. So if you have a CD player or an FM radio, you can connect the BTA 20 to it, and transmit to your Soundgear (or to other Bluetooth headphones that support the format). Please note that record players need an additional preamplifier to work this way. Of course a TV set can be connected as well, either via optical digital PCM output, via line outputs or via headphone output.

Yes, however, the JBL ONE App gives you another level of control over the speaker/soundbar.
Through the App, you can personalize the performance, such as:

• Customizing EQ settings
• Setting up our new feature called: My Moment 
• Connect your favorite streaming music services.

-       No, your Voice Assistant operates in the cloud and needs to be connected to the internet. .

Although the product is Water Resistant and Sweat Resistant, continuous exposure to water over an extended period of time may damage your earphones.

Although the product is Water Resistant and Sweat Resistant, continuous exposure to water over an extended period of time may damage your earphones.

No, JBL Flip 4 can wirelessly link with JBL Connect+ compatible speakers only. Currently, the Flip 4, Pulse 3 and Charge 3 ( after a firmware upgrade ) have the JBL Connect+ feature

Yes, you can use your Soundgear for TV watching or playing video games. You can use the TV speakers and the Soundgear simultaneously, they will be synchronized in time.

These units do not offer multi-voltage power supplies. However, you can use a domestic 110 volt component overseas with the addition of a step-down transformer, available at most electronics stores.

Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

What you need first

Make sure that these below things are checked before moving further:

1. You have the most recent version of the Google Home app installed 
2. Your LINK device is powered on (LINK 10 and LINK 20 with battery)
3. Your LINK device is plugged into a wall outlet (LINK 300, LINK 500 and LINK VIEW)
4. The LINK device is located near your router and you are standing next to it. 
5. The white LED lights in front of the LINK device are blinking, meaning it is ready to be set up
6. If you are using an Apple iOS device, then you need to turn on Bluetooth to install the device

   1. On your iOS device Home screen, tap Settings > Bluetooth.

   2. Make sure Bluetooth is On (toggled to the right and green).
   3. Return back to the Google Home app .
   4. Your LINK device should appear as "Set up this device" and you can continue with installing the LINK product.
7. If you are using an Android device, then you need to turn on Location services
   1. On your Android device, tap Settings .
   2. Tap Location > Turn on location.
   3. Tap Settings > Apps > Google Home app > Permissions.
   4. Next to "Location",  check the slider is On (toggled to the right and green)
   5. Your LINK device should appear as "Set up this device" and you can continue with installing the LINK product.

If you are still have trouble with installing your LINK devices then follow the steps below for further troubleshooting.

Troubleshooting

Step 1. Reboot your LINK device

1. Disconnect the power cable from your LINK device (300, 500 and VIEW) and for LINK 10 and LINK 20 simply turn the device "OFF". 
2. Reconnect power cable or turning the device ON for your LINK device. 

Step 2. Force close and relaunch the Google Home app      

1. From your Apple IOS device, do the following below:                   
   1. Press the Home button two times quickly. There will be a small preview of your recently used apps.      
   2. Select the app you want to close and swipe up towards the top of the screen.         
2. From your Android device, do the following below:              
   1. Launch the Recent Applications menu to see small previews of your recently used apps.                                 
   2. The Recent Apps button should be accessible at nearly any time along the bottom of the screen along with the other buttons on the virtual task bar.

Step 3. Check to see if the device is listed under “Ignored Devices” folder on the Devices tab      

1. Open the Google Home app.
2. In the top right corner of app home screen, tap Devices.
3. Scroll all the way down and make sure the LINK device is not listed under the Ignored Devices section.
4. NOTE: If you do not see any ignored devices, there is a chance that this section is not listed in the Google Home app.

Last thing to try​

If you are still experiencing issues with your LINK device not connecting to your Wireless network, then try the following:

1. Try finding another mobile device to set up your JBL LINK device, sometimes it can help connecting your LINK device.

2. Relocate your LINK device, or try to disable other Wireless network devices that might cause interference for your LINK device.

3. Perform a factory reset of your device, by holding down the mute button for 15 seconds (the LINK will now reboot and when the welcome message is heard then you can set it up again).
4. Reboot your Wireless router.           
5. Lastly, try turning Wi-Fi off and then back on again for your mobile device. Reopen your Google Home app and try again.

The functions that can be programmed from your TV remote control into Boost TV are Volume+ and Volume-, Mute and Power. No other functions can be learned.

Yes, the two model 300 versions are of identical size, and so are the two model 700 versions. The carrying cases can be purchased as spare parts.

No. The case can only be used to carry the speaker.

The Everest 300 ear pads can be replaced by owner, but it is not easy, and removing the old pads may damage them. So, it is not a bad idea to have new pads at hand before removing the old ones. Since they are glued in place with double-adhesive tape, it is necessary to rip them off with care. After removing the old ones, clean off any residue of the double-adhesive tape that held them in place from the headphone pods. Then remove the protective layer on the new pads, exposing the adhesive. Carefully align the new pad before pressing the edge. This is to prevent the glue from sticking before you get the pad into the right position. When the pad sits correctly, you can press the edge all the way round to make the adhesive stick securely.

Yes, both ELITE 300 and 700 can do this.

The headphones can pair to multiple devices but can only be connected to one device at a time.