How To
How To
1217 results
-
Yes, these headphones can be connected and paired to two devices at the same time.Was this helpful? Thank you for your feedback!
-
Yes, steam and drops of water in a bathroom are fine.Was this helpful? Thank you for your feedback!
-
Yes, steam and drops of water in a bathroom are fine.Was this helpful? Thank you for your feedback!
-
Yes, you can use them for telephone conversations in both Bluetooth and wired mode when paired with a smart device.Was this helpful? Thank you for your feedback!
-
Yes, you can play game either wired or wirelessly while using USB-C charging cable.Was this helpful? Thank you for your feedback!
-
Yes. Out-the-box the JBL Bar series soundbar recognizes volume and mute controls from the most common TV remote controls. The JBL Bar series has IR learning. You can use this feature to teach the soundbar to response to your TV's remote control as well.Was this helpful? Thank you for your feedback!
-
Yes, use the MONITOR OUT sockets (1/4” and RCA are available on 208P, RCA on ONE) to feed into a recording device. Please note that these outputs are volume controlled, so set the volume correctly, depending on the sensitivity of the recording device.Was this helpful? Thank you for your feedback!
-
It is possible to replace the ear pads, but there are details to consider. On Elite 700: The ear pads are held in place by a plastic plate with claws, and some of the claws will most likely break off when you remove the pad. You do this by grabbing under the edge where the fabric ends, then pulling hard outward. The claws will eventually let go, and some of them will break off, rattling inside the ear pod. The only way to get them out is to unscrew the speaker plate, lift it up, and shake out the broken-off claws. The new pads are simply centered over the speaker plate, and the claws pressed into the holes with a firm pressure. On Everest 700: The ear pads are glued into position with double-adhesive tape. Pull the old pads off with a forceful, steady pull, until the glue lets go. Remove the protective layer on the new pads, and carefully position them correctly before pressing home all the way around the edge.Was this helpful? Thank you for your feedback!
-
Yes, the ear pads are replaceable by owner. The pads can be purchased as spare parts from the service center, or purchased directly from the JBL spare parts web shop, when opened.Was this helpful? Thank you for your feedback!
-
No, the pads are glued to the headphone body, and must be replaced by a service technician.Was this helpful? Thank you for your feedback!
-
Yes, on the master speaker (the one with playback buttons), simply press the Reverse and Forward Play buttons at the same time for 3 seconds. Please note that after you have performed the reset procedure, master and secondary speakers are no longer connected. Go to the owner's manual page 4, the section "speaker association", to pair the secondary and master again.Was this helpful? Thank you for your feedback!
-
Yes it is possible to reset your speaker. The reset will remove all Bluetooth pairings and WiFi network settings. In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash. Your JBL Authentics L8 or L16, are now back to factory settings. Please reconnect the speaker to your WiFi network again.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)