How To
How To
1202 results
-
Alarm sound function in Bluetooth connectivity is not supported in iOS devices, however it is supported in Android devices.Was this helpful? Thank you for your feedback!
-
Yes, when changing volume to higher or lower, the LED will illuminate to show that you are changing the volume.Was this helpful? Thank you for your feedback!
-
The led indicator will be solid blue.Was this helpful? Thank you for your feedback!
-
This problem is usually caused by pressing down too hard on the soundbar's VOL + or VOL - Buttons. Only press just enough for one click to be felt. If a second click is felt in the button, you are pressing too hard, and you are actually activating the MUTE function for learning, not VOL up or down. You may have to repeatedly let go of the VOL button on the soundbar, followed by pressing it again and then pressing the VOL button on the TV remote before the surround light on the soundbar lights up white and goes back to amber flashing, as a sign that this function has been learned. This is no problem, though. Just keep trying until the three commands have been learned. The soundbar only exits learning mode when you press and hold the surround button as the final step.Was this helpful? Thank you for your feedback!
-
• Please check whether your head unit Bluetooth support EDR (Enhanced Data Rate) • If the head unit does not support EDR this will cause the transfer data rate to be low and will impact the audio quality.Was this helpful? Thank you for your feedback!
-
The PartyBoost feature is not available when your JBL speaker is connected to a computer via Bluetooth. This is a technical limitation. When connected to a computer, the computer is acting as the primary device. Therefore, the JBL speaker does not have control of re-transmitting the Bluetooth signal to other JBL speakers.
NOTE: Speakers effected by this are the JBL Flip 5, JBL Flip 6, JBL Charge 5, JBL Pulse 4, JBL Xtreme 3, and JBL Boombox 2, as well as all future products featuring the PartyBoost feature.Was this helpful? Thank you for your feedback! -
The wireless charge receiver in the smartphone may not be adequately coupled to the wireless charging transmitter on Smartbase. Re-adjust your smart phone’s position on the wireless charge arm.Was this helpful? Thank you for your feedback!
-
Some vehicles don’t provide an isolated ground for the head unit which may introduce noise. Please connect your smartphone to JBL DRG and enable the “Aux Noise Cancel” button in the App. This can be found right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
-
Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Focus 700 is actually the Focus 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Inspire 700 is actually the Inspire 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
Please press the round POWER Button on the FLIP again for 3 seconds, until the light in the button flashes blue/red. This will deactivate any active BT connection in the FLIP, and it should now become visible in the list of BT components on your smartphone or tablet. Pairing is now possible.Was this helpful? Thank you for your feedback!
-
JBL LINK 10 and LINK 20 has 32 volume steps, and LINK 300 and LINK 500 has 48 volume steps. For broader volume changes, hold down either the volume + or - butons. Use individual presses for fine volume adjustments.Was this helpful? Thank you for your feedback!
-
The volume level of the speaker is depends on the level of the source file itself. Some Dolby Atmos Music tracks are made to be quieter, and some louder.
Was this helpful? Thank you for your feedback! -
When a connected Bluetooth device goes out of range, the JBL Micro Wireless will try to reconnect to it for 3 minutes. After 3 minutes the Micro Wireless can connect to other Bluetooth devices again.Was this helpful? Thank you for your feedback!
-
In Bluetooth, there may be a small difference between the telephone (source) and the JBL Control X wireless unit. This means that they are not using the same scale. In any case, the difference will remain within one audio step on the phone or speaker.Was this helpful? Thank you for your feedback!
-
Soundshift only works for the Boost TV itself, and cannot stop the other JBL Connect device. To stop the second device, press the JBL Connect button on your remote or device and they will disconnect.Was this helpful? Thank you for your feedback!
-
If you see this message, you must download the Device Utility app from the Google Play Store. Follow the instructions in the app to activate your speaker, and then return to the Google Home app to complete the setup.
Was this helpful? Thank you for your feedback! -
This is addressed in the owner's manual. After associating a group of four speakers, when deciding to go back to normal operation as two pairs, it is recommended to reset them to factory default settings, which requires associating speaker pairs again.Was this helpful? Thank you for your feedback!
-
JBL Connect feature is using Bluetooth technology, so it is hard to say how far you can walk away. Depending on what other signals you have at your place that could interupt and wall material between speakers.Was this helpful? Thank you for your feedback!
-
JBL Connect feature is using Bluetooth technology, so it is hard to say how far you can walk away. Depending on what other signals you have at your place that could interupt and wall material between speakers.Was this helpful? Thank you for your feedback!
-
If the network does not appear, you can manually type in the network name (SSID) and password to connect.
Was this helpful? Thank you for your feedback! -
You can manually type in the network name (SSID) and password to connect if the network does not appear.Was this helpful? Thank you for your feedback!
-
When you have associated two pairs of speakers, the range between primary and secondary speakers (all 3 speakers), will be maximum 10 meters. The range will increase if you only use one pair of speakers (30 meters). We recommend placing the speakers on a high-level surface or shelf, for best possible connection.Was this helpful? Thank you for your feedback!
-
When using the JBL One app to control USB audio playback, please wait more than 1 second in between button presses.
Was this helpful? Thank you for your feedback! -
You should hear the audible voice stating ‘low battery’ when you have about 20 minutes left of battery life left on the UA WIRELESS headphones. If you have an Apple device, you will actually be able to see the battery life in the upper right hand corner of the device next to the BT symbol.Was this helpful? Thank you for your feedback!
-
If there is no activity on your JBL Boost TV, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.Was this helpful? Thank you for your feedback!
-
If there is no activity on your JBL SB 250, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.Was this helpful? Thank you for your feedback!
-
NOTE: LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).
Pairing issues with a Smartphone or Tablet:- First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
- Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
- Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
- If above does not work, then try to restart your JBL LINK device by turning it off and on again.
- Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
- Go into Bluetooth settings on your Smartphone/tablet.
- Perform a restart or reset if you are not able to connect after above steps.
JBL LINK Bluetooth specifications:- Bluetooth version 4.2
- A2DP v1.3 with SBC Audio Codec.
- AVRCP v1.5
Was this helpful? Thank you for your feedback! -
There are multiple ways to check your heart rate (HR) while using your headphones both in and out of workouts. On the UA Record mobile app select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your current heart rate will appear under the headphones' image. You will hear your heart rate when using the headphones during a UA Record workout with audio coaching. While using with your UA Band during a workout your HR will be shown with your workout stats and will coordinate with the HR zone LED on the Band. You also can simply tap the UA logo on the RIGHT ear bud to hear the audible voice stating your heart rate reading.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)