How To
How To
1217 results
-
In our Quick Start Guide, there is a section under "One Touch Play Feature", where we explain how it works. We advise to take a look at it.Was this helpful? Thank you for your feedback!
-
Press the microphone button (located on the LEFT arm) to turn on the first RunSafe mode. The first mode blinks continually. When you press the microphone again, the second mode is initiated which features 2 blinks on followed by 2 seconds without. Pressing the microphone again is the third mode which is 3 blinks on followed by 3 seconds without.Was this helpful? Thank you for your feedback!
-
BT sources are volume controlled by the Primary Volume control. BT volume relative to other sources must be adjusted either on the BT source or on the mixer’s input volume controls. Bluetooth does not occupy any of the other inputs.Was this helpful? Thank you for your feedback!
-
For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.Was this helpful? Thank you for your feedback!
-
Let's say you have 4 LINK devices in your home and you start your day with "OK Google, How is the weather?".
All of your devices will "light up" and start listening to the command. However, only one of the speakers will give you the information (if they are under the same account).
The speaker with the best microphone reception will respond with an answer.
Please note: if you have muted all speakers or 3 out of 4 are muted, then only one will respond and the rest will not react.
If all speakers are muted, all will be silent.Was this helpful? Thank you for your feedback! -
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
The JBL Quantum TWS works on most mobile devices, however, some mobile devices restrict the utilization of it's audio and microphone functions via USB-C causing there to be no audio or microphone operation. In these cases we recommend connecting to the earbuds using their Bluetooth connection.Was this helpful? Thank you for your feedback!
-
Switch the headphone ON, then press both volume buttons (VOL + and VOL-) at the same time, and hold them for 5-6 seconds. The headphones are now reset to factory default.Was this helpful? Thank you for your feedback!
-
If your JBL Link 10 or Link 20 is out of range, setting up a personal hotspot from your mobile device will allow your Google Assistant to answer again. However, this process requires two mobile smartphones, one as the "mobile hotspot" and the second to connect the JBL Link 10 or Link 20 to your network.Was this helpful? Thank you for your feedback!
-
By using Google Home app, and if a software is available then the app will notify you about the newest software available. Google Home app can be downloaded from Apple Play Store or Google Play Store.Was this helpful? Thank you for your feedback!
-
All updates will happen over-the-air, meaning that your device just needs to be connected via your Wi-Fi network with at least 30% battery and plugged into the charger, then it will update during the night if there are any new updates available.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)