How To
How To
1217 results
-
To pause/play music, press center button on RIGHT ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on RIGHT ear. Unfortunately, you cannot skip tracks backward.Was this helpful? Thank you for your feedback!
-
To charge the UA Flash, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly: 0= 0% Dead 2-3 = 40%-50% 4=100% Full battery lifeWas this helpful? Thank you for your feedback!
-
To take a phone call, press the center button of the RIGHT ear for 1 second. To hang up a call, press and hold the center button on the RIGHT ear for 1 second. To ignore a call, press and hold center button for 3 seconds until music resumes.Was this helpful? Thank you for your feedback!
-
The UA Flash does not support AptX or AAC audio codecsWas this helpful? Thank you for your feedback!
-
To activate Ambient Aware DOUBLE CLICK the center button located on the LEFT ear. You should hear the music level drop. To resume to normal music level, DOUBLE CLICK the center button on LEFT ear again.Was this helpful? Thank you for your feedback!
-
You can connect two of the same Partybox models (e.g. 2 x Partybox 310, or 2 x Partybox 100) together in TWS Mode by pressing and holding the Bluetooth button on both speakers for 5 seconds, or by pressing the dedicated TWS buttons on the rear panels of both speakers on the Partybox 110, 310 and 710. It is possible to pair two different Partybox models together using a wired connection (e.g. 1 x Partybox 310 and 1 x Partybox 100). It is also possible to pair two Partybox different models wirelessly in Party mode, however this is only possible with the newer Partybox models - the Partybox 110, 310 and 710. The Partybox 200 & 300 can be paired in TWS mode as they are the same model apart from the presence of a battery in the Partybox 300. If you connect an instrument or microphone to one Partybox speaker while using TWS, the instrument or microphone connected to one speaker will be reproduced by this speaker alone. You will not hear the instrument or microphone in both speakers. If it is necessary to have instruments reproduced by two or more PartyBox speakers, it is possible to use an RCA or aux cable – connected from the RCA, aux or daisy chain outputs on the speaker that the instrument or microphone is connected to, wired to the RCA, aux or daisy chain input of the secondary speaker. Alternatively a small mixing console can be used - connecting audio sources to this mixer and sending the mixed audio signal to the speakers with a wired connection.Was this helpful? Thank you for your feedback!
-
The two earpieces of your TWS headphones should normally be connected together without issue. However, if they are no longer paired to each other, please follow these steps, in order.
- Forget/unpair the headphones on your device.
- Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
- Pair the headphones to your device and see if this resolves the problem.
- If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
- Initiate a Product Reset to reset the earbud’s Bluetooth connection.
- Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
- Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
- Manually pair the 2 buds together again, as you did in step 2. This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
- Pair the buds to your Source Device.
Was this helpful? Thank you for your feedback! -
There is a rare issue causing some DAB radio stations not to be found after performing a scan.
If you are experiencing this, a firmware update has been released to fix the issue.
First, please read through the update instructions thoroughly, then proceed with installing the update.
Please click the link below to download the update:
JBL TUNER XLWas this helpful? Thank you for your feedback! -
There is a rare issue causing some DAB radio stations not to be found after performing a scan.
If you are experiencing this, a firmware update has been released to fix the issue.
First, please read through the update instructions thoroughly, then proceed with installing the update.
Please click the link below to download the update:
JBL TUNER 2
If you have any questions regarding the update or installation, please do not hesitate to contact us.
Was this helpful? Thank you for your feedback! -
TUNE FLEX 2
Software Update Release Notes
------------------------------------------------------------------------
Software Version: V2.2.0
Release Date: November 11th, 2024
Release Media: OTA (over the air) via JBL Headphone App
What’s New
- Add Google Find My Device support
- Stability and performance improvements
Was this helpful? Thank you for your feedback! -
Different ear tip types provide a different sound performance, depending on their shape. For a high-quality sound output, JBL specially tuned the sound according to different tips to fit your wearing preference.
o The Open Ear Tips mode allows more natural, while letting the surrounding noises come through.
o The Sealing Ear Tips provides more isolation from the surroundings.Was this helpful? Thank you for your feedback! -
JBL Tune Flex is packed with two types of ear tips. These are called “Open Ear Tips” and “Sealing Ear Tips”.
We recommend using the “Sealing Ear Tips” for extra isolation, secure fit and stability.
Ear tips in three sizes are included in the box. You can choose the size that best suits your preference and your ear configuration.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a support agent
Call us now at:
(800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Chat With Us
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)
Text Us
Text with a support agent via SMS at:
628-333-7807
Mon - Fri: 9:00 am - 11:00 pm (ET)
Sat - Sun: 9:00 am - 5:00 pm (ET)