|Ear cushion material||Frog skin PU leather|
|Headphone cable length (cm)||118.7|
|Headphone cable length (ft)||3.89|
|Headphones jack type||3.5 mm|
|Driver size (mm)||32.0|
|Dynamic frequency response range (Hz)||20 Hz - 20 kHz|
|Number of drivers per ear||1.0|
Documents & Downloads
What’s in the Box
- 1 pair of T450 headphones
- Warning Card
- Warranty Card
FAQs & How-Tos
Can I replace the ear pads on my T-series headphone?
Yes, the ear pads are replaceable by owner. The pads can be purchased as spare parts from the service center, or purchased directly from the JBL spare parts web shop, when opened.
Can the JBL T450BT be charged while listening to music?
No, as soon as charging begins, the headphone shuts down. Since no option for cabled listening exists for this model, it is necessary to charge before listening is again possible.
Waterproof InformationThis headphone does not have any IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to the headphones.
Can the ear pads of T450 and T450BT be replaced by owner?
Yes, T450 and T450BT ear pads can be removed and re-installed by owner. The pads are fixed by a lip going into a groove all the way around. Re-installation may need some care and time, but it can be done.
How can I reset my JBL headphones?
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.
My JBL Headphone App Support
This headphone is not supported by the My JBL Headphone app.
How many devices can I pair my T450 headphones to?
They support up to 8 paired devices without reset.
How long is the cable on JBL T450?
The cable is approximately 125 cm long, including the 3.5 mm 4-pole plug. Please note that this is valid for the wired T450 only. The wireless version, T450BT, cannot be used with cable at all.
How can I see that my T450BT is fully charged?
The charging LED stops lighting white, and goes dark.
Can the JBL T450BT be used with a cable?
No, this is a Bluetooth only headphone. Charging is done with cable, of course, but there is no cabled audio connection.
How Do I connect my T450BT via Bluetooth?
In normal use, T450BT pairing mode is automatic. First time it is switched on, it goes into pairing mode at once, shown by the blue LED blinking. After first pairing, if the last used source is not on when the T450BT is switched on, it will wait about 10 seconds with the LED showing white light, then it will switch to pairing mode, with the LED turning blue, and blinking. If you want to start pairing mode manually, make sure that the headphones are switched off, then press and hold the on/off button for more than 5 seconds. The headphones will now switch on in pairing mode, shown by the blue LED blinking.
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Can the T450BT headphone play with cable as well as Bluetooth?
No, this model is made for Bluetooth use only. There is no option for cabled connection.
Can’t find what you’re looking for?
Talk to a product expert
Call us now at: (800) 336-4525
Mon - Fri: 9:00 am - 11:00 pm (EST)
Sat - Sun: 9:00 am - 5:00 pm (EST)
Chat with Us
24/7 help with your order and information about our products