How To
How To
450 results
-
If the screen appears dark, try repositioning the Horizon 2 for the light sensor to work to the fullest. In some positions, the Horizon 2 cannot effectively detect the ambient light level in the room.
Was this helpful? Thank you for your feedback! -
You can have your own Karaoke party with your JBL Partybox. Simply connect your Microphone (only included with the Partybox On The Go) and connect your mobile device over Bluetooth, then start playing music and sing along, it is that simple!Was this helpful? Thank you for your feedback!
-
Please check that you have connected your android phone with JBL DRG before. Power off your Android phone and press the JBL DRG BT button to connect to another smartphone. If this is the case, please wait 3 minutes for JBL DRG to setup the Bluetooth connection with a new smartphone. This is because some android phones can’t send a “Disconnect” BT command to JBL DRG during power off, so JBL DRG need to wait until the Link is lost.Was this helpful? Thank you for your feedback!
-
Switch the Soundgear ON. (If this is not possible, reset cannot be performed.)
Press and hold Volume + and Volume - simultaneously for longer than five seconds.
Soundgear switches OFF, and is now reset to factory settings.Was this helpful? Thank you for your feedback! -
The JBL Quantum 400 headset is compatible via 3.5mm jack with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
You can use the USB connection with PC, PS4, Nintendo Switch, and Mac.Was this helpful? Thank you for your feedback! -
The JBL Quantum 300 headset is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
You can also use the included USB dongle on PC, PlayStation and Mac.Was this helpful? Thank you for your feedback! -
This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.Was this helpful? Thank you for your feedback!
-
Switching to a new Wi-Fi network
- Make sure your mobile device is connected to the same Wireless Network as your speaker.
- Open your Google Home app
- Go to Settings
- Tap on Wi-FI
Forget Network
- The current configuration is now forgotten.
- In your Google Home app, you are forced back to the "Home Screen" and need to setup the device again.
- Tap on
- Find Add
- Follow the instructions given to add the speaker to your Wi-Fi network.
Lost connection or changed settings
- Open the Google Home app
- On the home screen, tap on Add
- Follow the instruction provided.
- Remember that your current room name is the same as before, as well as other settings made for the speaker. You are only switching to a new Wi-Fi.
- In addition, you can click on Discovery
in the bottom menu of the Google Home app.
- Tap on the Setup
Was this helpful? Thank you for your feedback! -
To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.Was this helpful? Thank you for your feedback!
-
To activate TalkThru Technology, press the LEFT ear for a short press for 1 Second which allows you to clearly hear others for quick conversations without removing headphons. Music volume level should lower when TalkThru is engaged. Press again for 1 second to turn off Talk Thru.Was this helpful? Thank you for your feedback!
-
If the audio is not centered to your monitor, then you can re-center your headset by doing the following: 1. Position yourself in front of your monitor. 2. Press the re-centering button on the side of your headset (button that looks like a circle) 3. The head-tracking sensor will start the automatic calibration.Was this helpful? Thank you for your feedback!
-
This can be caused by the charge arm reaching its thermal temperature cutoff. This is a safety feature to prevent a potential risk. For proper heat dissipation, always be sure to have the charging arm in the open position when your smart phone is attached.Was this helpful? Thank you for your feedback!
-
Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.Was this helpful? Thank you for your feedback!
-
Common fixes:
(1) Make sure that the soundbar is not muted.
(2) Select the correct audio input source on the remote control.
(3) Check the connections to your TV or other devices
(4) Perform a reset if none of the above is working.
(4.1) Press and hold VOL -, VOL +, and Source buttons to perform a reset.
Was this helpful? Thank you for your feedback! -
When you press the power button you will hear a “door locked” tone. This means the top capacitive touch buttons have been locked. At this point you cannot trigger them. With another short press of the power button, you will hear a “door unlocked” tone, which means the top capacitive touch buttons have been unlocked.Was this helpful? Thank you for your feedback!
-
If your volume level is quiet, make sure that the TalkThru is not activated on your headphones. In order to deactivate or activate TalkThru, quickly press the ANC button located at the top of the LEFT ear cup. You will hear an audible voice stating, TalkThru On when activated, and 'ANC On' when deactivated.Was this helpful? Thank you for your feedback!
-
To pause/play music, tap center button on right or left ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on right or left ear. Unfortunately, you cannot skip tracks backward.Was this helpful? Thank you for your feedback!
-
To skip tracks forward, double click the PAUSE/PLAY to advance to the next track. Please note: You can only skip tracks forward. This speaker does not have the capability to skip to the previous track.Was this helpful? Thank you for your feedback!
-
Numbers 1-6 do NOT relate to ANC level, but you can find the optimal performance for your ears by selecting one of the bubbles.Was this helpful? Thank you for your feedback!
-
You can connect two of the same Partybox models (e.g. 2 x Partybox 310, or 2 x Partybox 100) together in TWS Mode by pressing and holding the Bluetooth button on both speakers for 5 seconds, or by pressing the dedicated TWS buttons on the rear panels of both speakers on the Partybox 110, 310 and 710. It is possible to pair two different Partybox models together using a wired connection (e.g. 1 x Partybox 310 and 1 x Partybox 100). It is also possible to pair two Partybox different models wirelessly in Party mode, however this is only possible with the newer Partybox models - the Partybox 110, 310 and 710. The Partybox 200 & 300 can be paired in TWS mode as they are the same model apart from the presence of a battery in the Partybox 300. If you connect an instrument or microphone to one Partybox speaker while using TWS, the instrument or microphone connected to one speaker will be reproduced by this speaker alone. You will not hear the instrument or microphone in both speakers. If it is necessary to have instruments reproduced by two or more PartyBox speakers, it is possible to use an RCA or aux cable – connected from the RCA, aux or daisy chain outputs on the speaker that the instrument or microphone is connected to, wired to the RCA, aux or daisy chain input of the secondary speaker. Alternatively a small mixing console can be used - connecting audio sources to this mixer and sending the mixed audio signal to the speakers with a wired connection.Was this helpful? Thank you for your feedback!
-
To activate Ambient Aware DOUBLE CLICK the center button located on the LEFT ear. You should hear the music level drop. To resume to normal music level, DOUBLE CLICK the center button on LEFT ear again.Was this helpful? Thank you for your feedback!
-
The UA Flash does not support AptX or AAC audio codecsWas this helpful? Thank you for your feedback!
-
To take a phone call, press the center button of the RIGHT ear for 1 second. To hang up a call, press and hold the center button on the RIGHT ear for 1 second. To ignore a call, press and hold center button for 3 seconds until music resumes.Was this helpful? Thank you for your feedback!
-
To charge the UA Flash, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly: 0= 0% Dead 2-3 = 40%-50% 4=100% Full battery lifeWas this helpful? Thank you for your feedback!
-
To pause/play music, press center button on RIGHT ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on RIGHT ear. Unfortunately, you cannot skip tracks backward.Was this helpful? Thank you for your feedback!
-
To connect to a new device, begin with the headphones powered off and hold the center button on the RIGHT headphone for 5 seconds to enter pairing mode. You will hear the BT pairing audible chime as it searches for a different device. Make sure the device you are wanting to connect to is in range and BT is on. Once connected you will hear the audible Connected chime. Once Right ear is connected, press and hold the center button on LEFT ear for 3 seconds as it powers on and connects to the device followed by the same Connected audible chime.Was this helpful? Thank you for your feedback!
-
To power on and pair the UA Flash, remove the ear tips from the charging case. If this is your first time using the headphones, they will automatically go into pairing mode. You will see the blue and red LED light flash on the RIGHT ear as it attempts to pair with your device. Make sure your device is in range and BT settings are ON. The JBL True Wireless Flash should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a slow blinking blue light below the UA logo on the RIGHT Ear. The RIGHT ear must be connected first in order to power on and connect the LEFT ear. To connect the LEFT ear, simply press and hold on the UA logo for 3-5 seconds until you hear the audible power on chime. (The left should automatically power on when you remove it from the case) Once powered on, it should connect to your device within a few seconds displaying a slow blinking blue LED light below the UA logo.Was this helpful? Thank you for your feedback!
-
To reset, Long press the (Right) button for 2s when the earbuds in the case, the blue LED will flash once to indicate reset is done.Was this helpful? Thank you for your feedback!
-
To activate Voice Assistant, press and hold the LEFT ear for 5 seconds until music stops and voice assistance asks what they can help you withWas this helpful? Thank you for your feedback!
-
AmbientAware Technology allows you to hear your surroundings without removing your UA Pivot headphones. To activate AmbientAware mode, double press the Bionic Hearing button on the controller. You will hear a tone, and your music level will lower when AmbientAware Technology is engaged. To revert back to normal volume, simply double press the Bionic Hearing button again.Was this helpful? Thank you for your feedback!
