How To
How To
450 results
-
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback! -
Once the sound bar is connected to the network, software updates will automatically be sent to the speaker/soundbar through Wi-Fi or the internet, if availableWas this helpful? Thank you for your feedback!
-
In the JBL ONE App:
(1) Go to My Products, select your product
(2) Select Support tile
(3) Under General, select Product SupportWas this helpful? Thank you for your feedback! -
Unfortunately, the JBL AmpUp App is no longer available for download.Was this helpful? Thank you for your feedback!
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks slowly for about two seconds, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds. The LED blinks two colors, and now you have reset to factory settings.Was this helpful? Thank you for your feedback!
-
To reset your JBL Tuner simply Long press Volume+ and Bluetooth button for 5-7 seconds. Your Tuner is now successfully reset and you can Bluetooth pair with it again.Was this helpful? Thank you for your feedback!
-
Press and hold the Source, Vol+ and Vol- buttons at the same time until you see the text "reset" on the soundbar's display.Was this helpful? Thank you for your feedback!
-
With the IPX7 rating, you can use them in water down to a depth of one meter, for maximum 30 minutes.Was this helpful? Thank you for your feedback!
-
Harman Volume on the Cinema Base has no levels, it's either on or off. It will remember the last setting when it's powered on. When you enable Harman Volume, you will hear audio feedback ( 4 tones going up when you turn it on, and 4 tones going down when you turn it off ) There is no visual indication that shows if it's on or offWas this helpful? Thank you for your feedback!
-
For models E40BT and E50BT Connect the first headphone by BT to your mobile device Tap the ShareMe button once Tap the ShareMe button on the 2nd headphones twice ( ! ) The headphones will connect to each other. When changing volume on source device, or BT connected headphones, the volume will only change on THAT headphone ( and in some cases the source device, like iOS devices and newer Android ), not on the one connected via ShareMe. When changing volume on a via-ShareMe-connected headphone ( 2nd ), it will not change volume on source device, or on the BT-connected headphone. To sum up, both headphones have their individual volumes. For Everest models ( not ELITE ). Connect the headphones by BT to your mobile device Put the 2nd device ( speaker, headphones as long as they have Bluetooth ) in "BT discovery mode" Press the ShareMe button on the Everest headphone ( button marked with a little "s" ) The Everest will connect to BT device. (Please note that you may not be able to pair from the Everest to the Everest Elite models, or if you can pair, you may have dropouts in sound). When changing volume on source device, or Everest, the volume will only change on the Everest ( and in some cases the source device, like iOS devices and newer Android ), not on the device connected via ShareMe. When changing volume on via-ShareMe-connected BT device ( 2nd ), it will not change volume on source device or Everest. Please note that it is NOT possible to use ShareMe if you are listening to analog signal via cable. Bot the E-series and the Everest models will switch off the Bluetooth circuits as soon as you insert the audio cable, so re-transmission is not possible.Was this helpful? Thank you for your feedback!
-
Press the microphone button (located on the LEFT arm) to turn on the first RunSafe mode. The first mode blinks continually. When you press the microphone again, the second mode is initiated which features 2 blinks on followed by 2 seconds without. Pressing the microphone again is the third mode which is 3 blinks on followed by 3 seconds without.Was this helpful? Thank you for your feedback!
-
Make sure the headphones are turned on and connected to your smart device. Press and hold the Microphone button located on the LEFT arm of the neckband. You should be able to activate Siri/Google within 3 seconds after pressing the Microphone button.Was this helpful? Thank you for your feedback!
-
1) Download and run the latest JBL Connect app on your phone 2) The JBL Connect app will begin discovering your JBL Boombox (please make sure your speaker is connected via Bluetooth first) 3) Use the toggle switch in the JBL Connect App to change the phone button to now have the voice assistant function 4) Simply press the “Play” button on your JBL Boombox (you will hear a brief tone) and begin speaking your commands via SIRI and Google Now. 5) Please check the below links for more information regarding SIRI and Google Now available voice commands: SIRI: https://support.apple.com/HT204389 Google Now: https://support.google.com/websearch/answer/2940021Was this helpful? Thank you for your feedback!
-
To answer and hang up calls, press the pause/play button located on the left arm of the Soundgear.Was this helpful? Thank you for your feedback!
-
The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.Was this helpful? Thank you for your feedback!
-
Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.Was this helpful? Thank you for your feedback!
-
• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.Was this helpful? Thank you for your feedback!
-
• Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.Was this helpful? Thank you for your feedback!
-
The Club 5501 is a mono amplifier for subwoofer use in cars. It can be confusing to see that it has two inputs, marked left and right, as well as two speaker output pairs. But it is still a mono amplifier, with only one channel. The two inputs are there to make it easier to connect to a normal car radio/head unit, where you will often have two normal full-range connectors, left and right. You can insert both into the 5501. However, if you only have one signal lead going to the 5501, you can use either of the inputs. They are combined into one inside the amplifier anyway. Also, the two sets of speaker connections are there to make it easier to connect two subwoofers simultaneously. The two sets are completely identical, so you can use either one for a single subwoofer, or both. If you connect two, they will be in parallel.Was this helpful? Thank you for your feedback!
-
The Stadium GTO 20M is intended for use with the Stadium GTO two-way systems, or to replace existing midrange speakers in systems that are already three-way from the start. The Stadium GTO two-way component systems are 3-way upgradeable. The crossovers are gap-switchable to accommodate a midrange upgrade. The optional Stadium GTO 20M midrange includes a bandpass crossover to convert a two-way system into a threeway system with perfect tonal balance. You simply connect both crossovers to the speaker wires from your car amplifier in parallel, and set the existing GTO two-way crossover to GAP function. Stadium GTO 20M is designed to also fit into many factory three-way applications. Please note that you cannot use this add-on midrange with coaxial car speakers, unless you can access the crossover networks to establish the midrange gap that the extra midrange is meant to occupy.Was this helpful? Thank you for your feedback!
-
If you cannot stream music with AirPlay, use the JBL One App;
(1) Go to Settings.
(2) Select 3rd Party Service.
(3) Select the Airplay tile.
(4) Select Reset AirPlay.Was this helpful? Thank you for your feedback! -
As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.Was this helpful? Thank you for your feedback!
-
Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.Was this helpful? Thank you for your feedback!
-
The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.Was this helpful? Thank you for your feedback!
-
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.Was this helpful? Thank you for your feedback!